Having problems with your Frigidaire Dishwashers ?
Dishwasher Not Getting Water
\015 I just installed new Frigidaire FDB1502RGC2 dishwasher. I'm getting power to the unit. When I start a cycle, I can hear the motor going (noisily, sounds sick - but new unit, not used to sounds) but there is no water going into the unit. After approximately 1 minute, the unit shuts off. I've checked the connections, no leaks. I don't see any noticeable kinks in the supply hose. Any ideas?\015
Repair Help & Product Troubleshooting for Frigidaire Dishwashers
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Asko diswasher Dishwasher will not get water. Lines all checked, water on. Pump runs even when in off. Problem started when there was a water clog in the sink next to the dishwasher, and the dishwasher backfilled with water. We used a shop vac to get the dirty water out. Next day tried to use dishwasher, runs, but no water and empying pump will not stop running. Ideas?
Check for water leaks or not draining/overfilling fault ... Asko D1776 Stainless Steel Built-in Dishwasher
No water my kenmore dishwasher is not getting any water. when we try to select normal wash or water miser cycle, the motor turns on, I can tell water is getting to the dishwasher because i can hear it running under the sink and feel it in the flexpipe that feeds the dishwasher. It is not getting anything inside though. Just wondering if you have any ideas. Thanks
SOUND LIKE YOU HAVE EITHER A FLOAT THAT IS STINKING OR A WATER INLET VAVLE THAT HAS FAILED. THE FOAT IS THE LITTLE MUSHROOM LIKE DOME WHICH IS PLACED AT THE FRONT LEFT SIDE UNDERNEATH THE BOTTOM RACK PULL UP GENTLY ON THE FLOAT UNTIL U HEAR A CLICK ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher
Dishwasher I have a whirlpool dishwasher that does not appear to be getting hot water. The washer water is cold initially and only seems to get warm once the heater in the base of the machine heats it. The hot water supply line does not get hot so I presume no water is being supplied. Is the water supposed to be hot at the start. If yes could this be caused be a faulty inlet valve and if so how can I check. The dishes are dirty especially on the top rack. Thanks for your help. David
Gendos is on track with his question. I have the same dishwasher and it doesn't get enough hot water to clean the dishes and runs for hours because the heating element wasn't designed to heat water, just maintain it. The only solution we have found ... Whirlpool GU2400XTP Built-in Dishwasher
Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".
Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers
I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p
I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers
Hi I have a Nemo Dishwasher and the top spray arm is not turning. The bottom one is going fine and there is certainly plenty of water getting into the washer as I opened the door with the washer going and it flood me. I can see the water getting into both spray arms - the bottom one has a excellent upward spray and turns - the upper spray arm has water getting into it but it will not turn. I have cleaned the dishwasher out and any internal parts that I could find so it is spotless - this is so f
... Fisher and Paykel DS602 Dishwasher
I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a
The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers
Hello, I have a CONSTRUCTA S9W1C dishwasher with aquastop. Unfortunately, I tried once to start it with the house water supply closed. Of course it stopped after a few seconds. After that time, when I start it, the water pumps works and after some seconds the cycle stops. It gets no water. I've checked and noticed that no water passes through the aquastop valve. The aqua stop has two wires that get into the dishwasher. Do you have any suggestions? Thank you for your time Alex
Disconnected dishwasher and moved out in order to tile the kitchen floor. Ten days later reconnected dishwasher. Turned on water supply to leak check -- no water is getting into the washer. - Ran hot water from sink side to see if that would help, no such luck - Disconnected water line and water is in the line up to the connection point at dishwasher. Looked inside valve of dishwasher for obstruction - no such luck - Disconnected both ends of water line and blew in line to check for obst
... Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher
Water jet arm does not work water goes into the dishwasher dishwasher drains but the arm does not work the dishes are not getting sprayed with hot water the dishes are not getting cleaned the soap in the dispenser does not all come out
In most units, the movement of the arm is powered by the water. If the water does not come out of the arms, check the filter for debris or the arm itself. This could also be caused by mechanical issues. You may want to inspect the arms itself for ... Dishwashers
Balay dishwasher Hi My dishwasher is broken.When I switch it on nothing happens.I have checked that the dishwasher is plugged in and the water is turned on.I used some hot water to try and get the dishwasher going.It mamaged to activate the sprayers and drain the remaining water.I suspect the water inlet solenoid is faulty! Can you please help me? Thanks, I look forward to hearing from you soon! Regards Alan
I have a whirlpool dishwasher DU915WKSO: when I turn the dishwasher on, the heating element comes on but no water comes into the unit. I recently replaced the garbage disposal and th dishwasher worked fine for a time or two. Since then I have only been able to get water in it once. Like I said, the heating element works but no water in the dishwasher. Thanks for any help.
... Whirlpool DU1055XTS Built-in Dishwasher
It appears that the dishwasher is not getting enough water. I have made sure that there is nothing blocking the door area so that the soap can dispense and I have reduced the amount of detergent to maybe a 1/2 Tablespoon. Have tried both powder and liquid detergents. Ran a sani clean cycle with the Jet Dry product for dishwasher used in the rural. I also run the hot water in the sink prior to starting the dishwasher to ensure the water is hot when it comes into the dishwasher. The detergent
Hello,Welcome to FixYa.Based on your description you`re experiencing the ... KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher
I changed my water control valve, thinking my dishwasher was not getting water, however, if I put water in the basin, dishwasher pumps the water out, however, it sounds like the dishwasher stays stuck in the drain mode, pump just continues to run?
Hi,\015\012\015\012There is a simple explanation for this - water is leaking into the bottom of your dishwasher under the washing compartment. This has caused the float to rise and trip the switch which activates the Aqua-Stop / anti-floo ... Bosch SHU9915UC Dishwasher
GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but
... GE 24 in. Profile PDW7300G Built-in Dishwasher
Dish-washer My dishwasher is not draining all of the water out of the dishwasher after it washes. I got someone to look at the drain pipes and he cleaned out the stuff and they still will not drain all of the water. I would like to know what I could do to get all of the water out of the dishwasher so that the water will come out of the bottom of the machine. Wanda
The problem is most likely that the pump empeller had been damage by pieces from a broken dish or a small piece of siverware. The only way to fix this is to take the dishwasher apart and replace the empeller. If you choose to do this yourself, you sh ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher
Hi there, Ok, i think i'mHi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fine through all the cycles. The only problem is that it has no water pressure. In other words water is pumping into the More Hi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fi
Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. In\015\012this case you’ll need to check the water inlet valve. Disconnect the power\015\012source to dis ... Dishwashers
Is there any way to get more water or higher pressure to my Frigidaire 300 Series dishwasher? The water in the kitchen has good pressure, but we can't get enough into dishwasher. Chip
Make sure the water supply valve to the dishwasher is fully open. There may be a internal main valve trouble restricting the water flow. Disassemtle to fix.\012\012Dishwashers are typically filled by one of two methods: ( ... Frigidaire Dishwashers
My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This
By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher
My tappan dishwasher is only 1 1/2 yr old and its not getting at least 1/2 of dishes clean. We have tried everything from changing to liquid soap, increasing water pressure at meter, not using while washing clothes. We used a dishwasher cleaner to remove calcium, and run hot water in sink before using. We know the wand, pump and drain are working. It is model TDB210RFB5 with 1.1A motor. Is the motor too small to clean dishes? I wish I could get my money back or exchange for an upgrade. Thanks!
... Electrolux Dishwashers
I have a Whirlpool DU810SWLQ0 that will not drain. I've pulled the unit out, snaked the drain tube, pulled the motor/pump, and pipe assemblies, and cleaned the food trap, which I also removed. I've run the dishwasher with a bit of bleach, and the water will pump in, get processed by the agitator, and be heated. When the rinse cycle comes, dishes get covered in food, and are never clean. Waste water was being used for a clean rinse. I've run the dishwasher with the drain dangling in a bucket,
Refer the wash system assembly dwg. Check if the ball (item 21) is sitting correctly. If it is out of ali ... Dishwashers
Dishwasher not getting enough water in either drawer, although top drawer gets more. Dishwasher keeps beeping during cycle and reads not enough water and then stops running until you press the start button. Need Help, any ideas?
This sounds like a hard water deposit problem.Check your water inlet valve for a screen and see if its clogged. Also it may just be a water valve/solenoid problem. As in, it's too crusted up to float up and down.Some models have a water f ... Fisher and Paykel DD605FD Stainless Steel Built-in Dishwasher
Have a Westinghouse 905 dishwasher (guessing approx 5-10yrs old). When I turn it on it's starts is cycle as expected then stops after about 10mins and loses all power (can't turn it on or get any lights to light up for sometime almost like it needs to cool down) at this point the dishwasher is full of water. It is not the pump however as as soon as you can get power to it (sometimes some hours later) and turn it on the first thing it does is pump out the water. Any ideas??
It is likely the thermal relay is tripping. This could be because if you are feeding hot water to inlet the temperature of water is too high, or the dishwasher heater is faulty and overheating the water. Or it is also possible the thermal cutout is s ... Westinghouse Dishwashers
Kenmore dishwasher. The upper rack is not getting clean. Even very light residue remains. And, detergent is left in door at end of cycle. The bottom is filling up, so I don't think it's the intake valve. Also, all the blade openings appear clear. I am noticing that hot water is not filling the dishwasher when I first run the cycle. Even if I have hot water running in the sink, the dishwasher fills with cold or warm water. So, I think this is the problem. What should I do? Thank you in advance!
I find it odd that the dishwasher is filling with cold water if the water is hot at the sink. It sounds like the dishwasher is connected to the cold water line rather than the hot. Check under your sink; if you've got standard plumbing, the dishwas ... Dishwashers
LG dishwasher I have just installed an LG dishwasher. When I try to run the dishwasher it sounds as if it is getting no water. I checked the water supply line twice, and nothing is blocking it. The line is attached to the hot water under the sink and is open.
I bought a stainless steel Lg less than 15 months ago for 800.00and it stopped working. The manufacture said so sorry even though you didn't take delivery until the end of Jan. your warranty goes by purchase date. I would of been better of with a may ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher