Having problems with your Frigidaire Dishwashers ?

Can hear pump running but no water circulating


Answers :

Check your chopper.
Repair Help & Product Troubleshooting for Frigidaire Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When I started it, it made a loud grinding sound which continued whenever it was actually washing/rinsing. It was washing and rinsing the dishes ok. Eventually I didn't hear anymore grinding but the dishes had not been washed or rinsed. The detergent cup was open and the detergent spilled down the door. I ran it again and could hear the pump running. It ran through the cycles but the water was not being circulated. I suspect that something is caught in the disposer blade or something and is bloc


What is the brand and model number. it likely will have to be disassembled to clean it out. is it a built in dishwasher or a stand alone type ? ... Dishwashers

Can hear pump running but no water circulating


Check your chopper. ... Frigidaire Dishwashers

The circulation pump on my FDW60 was siezed .I have replaced this with a working one . When I turn on the normal 55 lights up and will not change it sounds as tho motor is working can't hear water running in .Turned off sharpish to save heater


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Shu9925uc/14 bosch dishwasher leaves standing water in the bottom of the pump. The pump seems to be bad because it wont drain out the back hose. I have run the diswasher full cycle and put the drain hose into the sink to test. It wont drain at all now and I dont hear the pump. Perhaps unrelated: Pump seemed to stop working after the back hose disconnected itself from the back of the unit spilling water all over the floor. When I reconnected the unit to the wall the pump now seems to be disfunct


Hi Dishwasher not draining issue occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remove then turn off the dish ... Bosch SHU9925UC Built-in Dishwasher

My Bosch diswasher is hanging up in the cycle (at 102 mins. in normal cycle and 38 mins in quick cycle). I hear what sounds like a one second pumping of water into the sink area, a pause, and then another one second pumping of water, on and on, but there's no progression beyond this point. One possible cause: a few weeks ago someone turned off the hot water at the heater and another person tried to run the dishwasher. The dishwasher did not function because it could not get hot water. Perhaps


Hi\015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. To start with check the water inlet valve which is located\015\012behind the lower access panel on the left or right side of the Di ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

No water I have the kenmore ultra wash quiet guard built in. You can hear the motor running but it is not drawing water into the machine. I have checked all of the hoses and connections and they are good....pump sounds like its running but just wont draw the water in.


Inlet solenoid not working, check wiring is attached ... Kenmore 24 in. 15932 Built-in Dishwasher

I have a fridgidaire Gallery dishwasher model # FDB949GFS2. It was not spraying water while running, so I checked for clogged wash arms and hoses etc. So I replaced the motor assembly and now I hear the motor running, it fills with hot water but it is still not circulating water. Is there something else I need to check. Thanks Tom


Most likely the wash sump is blocked. Refer this diagram. You will have to open the sump (item 14) and loo ... Frigidaire FDB949GF Dishwasher

EDW5500DSS wont completely drain water Okay so now that my dishwasher runs, when it finishes a cycle it has a nice puddle of water at the bottom that never drains completely out. I am assuming its a relay or something because I looked for a floating switch (did not find), I can hear a pump sound as if it wants to pump the remaining water out, but, it doesn't. I really want to solve this problem soon so I can order the new door seal and needed part together. Checked the line out and of course i


The srainer over the pump could be clogged not letting the water drain quick enough. Be sure the screen is cleane out. I believe you would have already checked and cleaned this. I believe it is the impeller on the pump that pumps the water that is ei ... Dishwashers

After cycle completed, opened door and found water did not drain. i removed the screen at the bottom and used wetvac to **** all the water out. i was also able to hear suction from hose to sink P trap. i'm confident there is no blockage. i attempted to run again only to find out the pump was running but, no water was filling the machine. Yes! the valves are open! two different issues? one other thing; due to the no thought behind this, the name plate was stuck to the inner part of the door whi


Possible that the drain pump needs a closer look , clean and check if the pump is working. If there is voltage to the pump during the drian then the pump is faulty.\012The second issue if the inlet chocking , check the inlet filter , check the ... Bosch SHU9915UC Dishwasher

I have a GE dishwasher model GLDL560N10SS. I noticed a burning smell coming from it the other day and then realized that although I can hear water running into the dishwasher when I start it, it never actually runs in the sense that the water is pushed through the various outlets to wash the dishes. I'm assuming that it is because the unit is dry and the heating element is still coming on that it is causing a burning smell. If I open the unit and reset it, it pumps the water back out into the si


The problem sounds like it is in the water inlet selonoid. Pull off the bottom panel and this is the part that the main water line hooks to there is a selonoid and it has a plugg inconnection to it unplugg it and check for power when the unit is supp ... Dishwashers

Disposal plugged up and water backed up into dishwasher. Cleared disposal and dishwasher drain line. Checked around sump but dishwasher won't pump out. Sounds like pump is trying to run. I can blow air through the drain hose from the disposal and get bubbles in the water. Turned off breaker for 1 min. then tried reset. Can hear pump humming.


The pump is humming because its still trying to get all the water out of the unit. Deinstall the dishwasher and pull the entire dishwasher out from under your cabinet. Next step would be to disconnect the drain line from the drain pump and check to ... Dishwashers

Maytag Model No WU202 is running through all cycles but is not pumping out the water from the tub. I can hear the pump running and a gurgling sound. Could it be the micro mesh filter that is plugged? Any detailed drawings available of the lower wash assembly and instructions to take it appart? This machine is more than twenty years old.


Hi,It sounds like your belt broke. Open the bottom access panel below your door and check. The part is :-http://www.repairclinic.com/SSPartDetail.aspx?PartID=2814&PPStack=1If you take off the front ... Maytag Dishwashers

I have a jennair dishwasher, Model # JDB1100AWS, it fills up with water, heats to temp, I hear wter pump run, but no water being pumped throgh any of the wash arms


I can't read the comments posted by the other consultant. Not sure why the problem is still active.\015\012\015\012It is likely there is dirt in the arms. you may need to clean these. ... Dishwashers

Recently our GU1100XTLQ1 started having a problem. It barely cleans the bottom rack, and barely gets top rack wet. The soap stays stuck in the dispenser. I can't see inside as it runs, but my guess is that not enough water is being shot out of the various spinning arms. From looking at diagrams it would appear that this dishwasher uses a pump to circulate water from the bottom of the cavity through the spinning arms. Is my problem a dying pump?


... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

Model#SHX4AP05UC/04 on start up can hear pump running water fills for 30 sec then pump runs stops and clean led is on ?


... Bosch Dishwashers

Asko D3530 water inlet fault code, water valve is on, water comes in but after water comes in for a couple of minutes we get a (inlet water fault code) check power at circulating pump no 120v unit will not run reset system it will drain and start cycle again with same result


Hello,\015\012\015\012It is common for these valves to "appear" to be ok, meaning they begin to allow water into the unit, but then one of the two coils or plungers inside fail, or are clogged with mineral deposit from the water or other ... Asko 24 in. D3530FI Built-in Dishwasher

GLD4050 DW won't pump out at any time during wash cycle. Removed lower arm, screen, etc. and washed and cleaned out everything. Removed drain hose and cleaned it out. Reinstalled and ran again. At no time during he cycle does the water pump out. HOWEVER, if I put my hand on the drain pump I can feel and hear the pump running as usual at the right times in the cycle. What else could be preventing the pump out? Thanks!


You could have a plugged pump itself or broken propellers as long as drain and screen are clean which looks like you already took care of that. ... Frigidaire GLD4050RHS Builtin Dishwasher

Hello, Please help. I follow recommendations for cleaning: sewer pump, cleaning arms, screens of the dishwasher. However, still machine is not working. water is not going through arms: lower, middle or top. Also, I get water into dishwater when it starts, and when I open i hear noise for water dripping into hot elements,but no water is running throughout. PLEASE HELP


... KitchenAid 24 in. KUDP01IL Stainless Steel Free-standing Dishwasher

"Sensing" Light Moved a 5 year old dishwasher that was functioning just fine to a different location. Hooked everything up and gave it a test run without any dishes in it. Fills and heats water properly, then buzzing noise heard for a ling time and then it drains the water out, with out circulating the water into the washer arms, etc. Any guesses? Could something have gotten lodged in the pump during transport?


There is a relay on the soap dispenser, if it is a Kenmore quietguard 4, I had the same type of noise, the repairman replaced the dispenser, which to me made no sense, because the relay is activated from the control board. After the $130. for the soa ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Pump to discharge water is underpreforming. won't empty standing water in bottom of unit when cycle is over. will dichsrge water when dicharge tubing is lowered to downhill slope. can hear motor running


Disassemble the drain and pump area, you will mostlikely find particulate matter restricting flow. ... KitchenAid Dishwashers

Obtained this haier hdp18pa portable dishwasher, thought I would give it a try. The unit will not fill with water, turn the power on you can hear the motor or the pump running but no water comes in. THe 4 display lights flash and beep a series of times and then stop only to repeat the sound off in a every few second sequence. I have tried the remedies offered online, tilting the unit does not seem to work for me on this one. I changed out the water inlet valve but nothing changed and I got the s


HiYou need to clean the filter that is in the tube that gets water in the dishwasherin case you can not find it pls ask me to send you a diagram ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

I bought a secondhand Miele 2830 LaPerla dishwasher. I hooked it up today. As soon as I pressed the start button, i heard the pump anf it gave me an F68 error and water leaked out of the bottom in such a way that I could not see where it was coming from. I know f68 means the circulation pump is running when it isn't supposed to. Since I heard the pump, I imagine that is working. So any advice on how to fix this?


The hoses may not be connected properly or are cracked. This is causing leakage inside dishwasher and the flood switch to operate. The dishwasher starts the pump to empty the dishwasher and avoid damage of water flooding the electric parts.Yo ... Dishwashers

I received a second-hand as-is Akso D3530 (model #107353001) dishwasher. It washes perfectly fine, but at the end of the cycle, it keeps running. It does not seem to be the drain that is running, but rather the circulating pump. I have fully emptied the pan of water (there was only a little in it (you couldn't see it until you removed the sieve) using a turkey baster and it keeps running. I also checked the float sensor in the bottom. The float sensor is not tripped, and when I manually trip it,


Hi.The float switch is not a water level switch, but an overfill switch. The control board uses the input from the pressure sensor to decide when to stop the pump.When you open the float switch circuit the machine 'thinks' that ther ... Asko 24 in. D3530FI Built-in Dishwasher

SGS5022GB/07 Dishwasher. Water seems to be pumping into unit but not washing dishes. Full cycle running but doesn't seem to be any water circulating.


... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1380 seconds