Having problems with your Frigidaire Dishwashers ?

I have a PLD3460RDC1 dishwasher.The power got shut off and it now displays an ER message with all the other lights blinking.I have shut off the power to the unit many times, first getting a PF error and then it goes to the ER with all lights blinking. How can I reset this?


Answers :

HI, there has been a power surge/pulse, that has been absorbed by the electronic control board. There may be serious damaged here, in this case. You can try to reset the main logic chips by unplugging, or shutting power down for five minutes. If the error continues after the reset, this will confirm that the electronic control board is damaged beyond repair, and it should be replaced asap.

Expert Solution:- Replace the electronic control #154488901
Repair Help & Product Troubleshooting for Frigidaire Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a PLD3460RDC1 dishwasher.The power got shut off and it now displays an ER message with all the other lights blinking.I have shut off the power to the unit many times, first getting a PF error and then it goes to the ER with all lights blinking. How can I reset this?


HI, there has been a power surge/pulse, that has been absorbed by the electronic control board. There may be serious damaged here, in this case. You can try to reset the main logic chips by unplugging, or shutting power down for five minutes. If the ... Frigidaire Dishwashers

The power is going to the dishwasher. The on off buttons work. No error codes. The salt light is lite (has been for 5 years) but now I get zero response when shutting the door (after selecting any of the 6 run options). There is no noise, no water, nothing happens. How do I repair this dishwasher so that it will run again?


Door switch failure. This will shut down all other start options. Inspect and possible replacement. See if you can activate it with something with door open. Give it a good close look... ... Dishwashers

Have a Westinghouse 905 dishwasher (guessing approx 5-10yrs old). When I turn it on it's starts is cycle as expected then stops after about 10mins and loses all power (can't turn it on or get any lights to light up for sometime almost like it needs to cool down) at this point the dishwasher is full of water. It is not the pump however as as soon as you can get power to it (sometimes some hours later) and turn it on the first thing it does is pump out the water. Any ideas??


It is likely the thermal relay is tripping. This could be because if you are feeding hot water to inlet the temperature of water is too high, or the dishwasher heater is faulty and overheating the water. Or it is also possible the thermal cutout is s ... Westinghouse Dishwashers

Whirlpool ADP6000WH No Power up We started a cycle , then all of a Sudden it shut off completely.... No error code at all and no lights or Display. No fuses in the House were thrown and i've tested the power point on the wall and all is ok. Just no response when pressing the Power Button on the Dishwasher??? Please Help :)


... Dishwashers

I have just moved into a home with the DS-603i and used it for the first time. I put it on the first load and seemed to go for way to long. so i opened it up and t washed the first load ok, but continued to make noises. It would make these noises even when draw opened. Turn on & off at power and it doesn't change the noises. The light on inside indicates rince, which i think is a F1 error code according to the manual online. Any tips on how to fix this?


The F1 error code indicated a leak problem. The noise that you hear is from the pump motor. There is a leak due to the top lid not sealed properly, so the water is shooting out during the wash cycle. It did not seal tightly because there are 2 actuat ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers

Hobart commercial under the counter diswasher LXIC Model Number 130016. DELIME light comes on every day at startup. Machine will immediatly run (in DELIME mode I think) for about 5-10 min and then get E4 error. We unplug power to the unit let it set, replug it back in after 3-4 cycles of this, it will eventually work perfect for the entire day. I have replaced the Sensor that is on bottom front of the unit in the water trough. ( I replace the sensor to the right if you are looking at the un


Q have your run a descaler . to rid the machine of its deposits . in order for the machine to run properly the parts and pump / screens must be clean . / descaling for deliming . dishwasher and icemakers is comm ... Hobart LXIC-6 Dishwasher

I have a Indesit IDL 600 S dishwasher. Yesterday a cycle there was unfortunatly a power failure. I am now, unable to get the machine to regain any of it's cycles, it just remains stuck in it's first position (light one on) and will go no further. Is there a way I am able to reset the machine? Many thanks


... Indesit 24 in. IDL500 Built-In Dishwasher

Dishwasher is making a metalic rattling/clanking noise when first starting and periodically through the wash cycle. Sounds like the noise is in the door, but hard to tell. No error lights have come on. The dishes appear clean, but the noise is getting worse.


... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

All the programme cycle lights come when any programme is selected. I have opened and cleaned the filters, drain pump and non-return valve. I have switched power off at the mains. I have also depressed the off switch for 5 secs as recommended on the Miele website and then re-started the machine. Still get the same error. Any suggestions would be gratefully received.


Hi\015\012\015\012Try and reset the dishwasher by following this sequence---\015\012\015\012Turn the power off to the machine.\015\012Press and hold button 2 and 3 together while turning the dishwasher on. The salt and i ... Dishwashers

Mod# mdb7601aww.... When I press cycle key, say heavy duty, then close door the 2H light flashes. I press the start button and the unit will not start. I have shut it down electricly and get the same results. what can be the problem? The front panel with the start/delay buttons or the inside control panel? I like to figure this on out the first time because each of those parts are $100+.


... Maytag Dishwashers

Have a frigidaire dishwasher (model- PLD4375RFC0)about 2 years old. Set to run as we left to go out of town- when we came back all lights flashing including error- found a child's plastic bowl that had fallen to the bottom and had a melted spot as it was next to the heating element. Called support and were told to master restart- shut the power off for 15 minutes. Did and now flashing "27". Cannot find a code for that and neither could support without sending out a repairman. Any advice before


... Frigidaire Dishwashers

I have a Frigidaire 4000 Series Dishwasher, Model# FDB4315FCO, almost six years old. It acts as if there is no power. There is no error code. If I pull the power cord I get a "PF" message.


... Dishwashers

MY BOSCH DISHWASHER MODEL #SHU43C06UC/17 WILL NOT START. NONE OF THE LIGHTS TURN ON AS IF THERE IS NO POWER GETTING TO IT. I HAVE CHECKED THE POWER CORD AND THE BREAKER BOX AND EVERYTHING IS O.K., BUT I STILL CAN NOT GET IT TO TURN ON. AT ONE TIME THE LED LIGHT LIT UP FOR A BRIEF SECOND, BUT NEVER AGAIN. ANY OTHER SUGGESTION?


Hi-Check if there is a fuse at the back of the unit or inside of it. Replace if there is any.Keep us updated, thanksHope this helps ... Bosch Dishwashers

Have a kitchenaid dishwasher KUDS25SHWH1 - the child-lock light came on and will not go off. It is a light and no button to push and hold except all of the select buttons for the type of wash you want, no air dry button. How do I get this light off?? The Child Lock light has come on by it's self and I cannot get it to turn off. I have never used this feature before. I have tried to hold the Energy Saver button for several seconds but the Child Lock light will not shut off. The dishwasher is loc


Unplug the unit for 15 minutes then plug it back in. This should reset all your computer system and make everything work again ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

I have a Whirlpool ADF951, it has power to it and was working fine, the power light is on and the green light to the far right of the cycle lights is flashing, I can only get any response if I hold the start button in for about 10-15 seconds, The machine stops the light flashing and makes the noise like it is starting , that goes for about 20 secs then returns to the flashing light stage, any idea's please


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water tempera ... Dishwashers

I know it's getting power because the cancel light is lighting up but I can't get any cycle to start (no other light will even light up).


... Jenn-Air JDB3600AWP Dishwasher

I know it's getting power because the cancel light is lighting up but I can't get any cycle to start (no other light will even light up).


... Jenn-Air JDB3600AWP Dishwasher

What does the F2 Error mean? I got that error thsi morning. The engine was buzzing so I turned the power off. I have cleared what appears to be calcium and/or soap build-up in the 3 filters and in the drain. When I turn the power back on I still get the F2 error. How can I restart the machine and turn off the F2 Error?


The F2 error means the tray underneath the unit has filled with water.\015\012You will need to pull out the dishwasher (remove 2 screws at top left/right when door open that prevent tilting).\015\012Unplug and pull out dishwasher.\015\012Remove 4 scr ... Asko D1876 Dishwasher

Smeg DF612S All starts well but after 40 minutes stops with a beep and will not progress to the main wash cycle. Instead all programme lights come on (located on the left), along with the first 2 phase lights (the first two of the lights on the right hand panel). This indicates error code 3 (cannot pump out water), but water is entering and draining perfectly. Please advise.


Check to make sure there r no kinks’ in the drain line or\015\012that it is not clogged it sounds like the sensor is tripping because there is\015\012too much strain on the pump just like a breaker. ... Smeg 24 in. DWI612 Built-in Dishwasher

We have a kitchenAid dishwasher -- just installed last year new-- we cannot get the rinse aid low light to go off. We have filled it up to where it can no longer hold anymore and the light is still on. I have tried to cut the power on/off and it still remains on. Any suggestions on how to get the light to go off? thank you.


Check to see if the "Heat Dry/Lock" button is lit up. If it is, press the button and hold it for four seconds to unlock your dishwasher controls.Close your dishwasher door firmly and press the "Cancel" button. Wait two minutes for your Ki ... KitchenAid Dishwashers

We have a Maytag MDBH945AWW3 dishwasher. It is acting like there is no power getting to the machine (all buttons are unresponsive and no LED's light up), but there is DEFINITELY power getting to the machine. Ideas... or even a test procedure to help diagnose which item might be broken?


Where exactly is the power getting to? ... Maytag Jetclean II MDBH945AWS Stainless Steel Built-in Dishwasher

Cycle interrruption Recently, about 20 minutes into the wash cycle, the unit shuts down and the lights start blinking - usually "Pots & Pans" & "Quick Rinse" simultaneously. No other buttons respond and I cannot get it to finish the cycle. Only shutting down the unit at the fuse box eliminates the lights. I've checked for blockages and nothing found. Manual does not offer any help or suggestions. Any ideas??


Relace control board. ... Kenmore 24 in. 16032 Built-in Dishwasher

Kitchenaid model KUDIO1ILBL6 The lights for Heavy Cycle ,Normal Cycle and Cancel blinking at the sametime constantly. The tech sheet is missing and the unit is appox. 5years old.have shut power down for 5 minutes .When power turn back on only the Heavy Cycle light blinks costantly. Have Ohmed out the door switches and check adjustment OK. Checked board strips and plugs for good clean and tight connections OK. Thanks


Hi, You need to reset the unit by pushing the buttons. Push the heated wash/heated dry a few times. All the lights will light up and the dishwasher will continue its . Let ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1502 seconds