Having problems with your Frigidaire Dishwashers ?

FDB2310LCC1 - my dishwasher has stopped working - it seems to make noise and try but the water does not dispurse....is it the motor?


Answers :

Hi,
\015\012If your dishwasher seems noisy, the following reason can occur…
\015\012Water-inlet valve
\015\012An aging water-inlet valve can sometimes fail slowly, rather than all at once. It can shudder on and off rapidly, causing the incoming water lines to shake, rumble, and rattle--sometimes violently. If yours is doing this, replace the inlet valve.
\015\012Motor
\015\012If it's the motor that's noisy, either of these might be the reason. As motor bearings wear out, they can become quite loud when the motor runs. They wear out quickly if they frequently get wet, because the water washes away the motor bearing grease. Bearings can get wet if the spin seal is defective. Then there will also be water leaking onto the floor beneath the dishwasher. Replace the seal if it leaks
\015\012If, from beneath the dishwasher, you can see a round, plastic disc that's mounted to the top of the motor (a "slinger"), it may have broken free of the motor shaft. If so, it could be rattling around the shaft while the motor is running. If that's the problem, you need to replace the motor.
\015\012Heater fan
\015\012If the heater fan bearings are rusted or worn, they may squeal, or scrape loudly during the drying cycle. If this is the problem, replace the fan motor. Alternatively, the fan blade may be loose. If so, you need to replace it.
\015\012Pump
\015\012Small fruit pits, toothpicks, and fragments of glass sometimes get stuck in the pump. When this happens, open the pump and remove the debris. The pump is usually mounted directly to the motor, then attached to the bottom of the dishwasher.
\015\012To get to the pump, you usually need to remove the lower rack, the spray arms, and the spray arm support from the inside of your dishwasher. A dishwasher pump isn't obvious. Look for an impeller--a round, plastic fan blade-type device that spins around and pushes the water toward the drain. When you can see the drain impeller, you should be able to see the clogging debris.
\015\012Please let us know if you were looking for something else or please accept the solution.
\015\012Thank You for contacting Fixya.com
Repair Help & Product Troubleshooting for Frigidaire Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have GE GSD2300r00bb, it was working just fine the other day no unusual noise, today we tried to run it, just a little bit into the cycle, i heard a strange stalling noise that sound like the motor is stuck or something, i put a camera(in a ziplock bag) in the dishwasher to see if the blade is spinning, no spin, the water did squirt for about 1 sec then stop but still leaking out somewater. Is it the motor or the water pump. I just got this dishwasher about 1.5 yrs. Is this something i can fix


... GE GSD2300RBB Builtin Dishwasher

Won't start After two months of no use my dishwasher won't work. I can hear motor running but no water. We tried cleaning by filling with water (priming motor) but nothing happens. Now the dishwasher if full with water, motor makes noise but nothing is happening. Help!!


It sounds like you have a food blockage or some blockage between where the water fills up and where it goes into the pump you need to take out the water wand (the rotating thing with water coming out) only the bottom one. You need to unscrew the wate ... Hotpoint 24 in. HDA1000Z Built-in Dishwasher

Kenmore Elite dishwasher Model #665 1597 2992 Machine fills with water but thereafter it neither washes nor drains. Machine will not drain when I advance the cycle by pressing the Cancel/Drain button. There was a report that there was some noise when the machine first failed. I do not hear anything when I try to run a cycle. What might the problem be? How does one turn the motor manually to see if it is bound up by something? If it is the motor do I want to pay an extra $70 to $100 and


... Dishwashers

FDB2310LCC1 - my dishwasher has stopped working - it seems to make noise and try but the water does not dispurse....is it the motor?


Hi,\015\012If your dishwasher seems noisy, the following reason can occur… \015\012Water-inlet valve …\015\012An aging water-inlet valve can sometimes fa ... Frigidaire Dishwashers

Service Manual Dear Sir, We are in the UK and although my double drawer dishwasher is branded Whirlpool ADG2900, I see that it is made by Fisher & Paykel. The top drawer motor started making a different noise about 3 months ago and now there is some dirty water left in the drawer after the cycle completes. The pots remain dirty. If you could get me the service manual I could try and sort it out. Please help! Thanks, RP.


... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My 1yo slimline hotpoint dishwasher LST216 has developed a fault when trying to run the 'normal wash': washing stops after a couple of mins, the lights start flashing and the alarm comes on as soon as the water is being drawn into the machine. When I open the door I can hear a whirling/grating motor noise coming from the bottom of the machine. I have cleaned all filters and have run other programmes to check overall functionality and they all work as expected most of the time. I cannot unders


... Hotpoint Dishwashers

After a power outage, that occured while the dishwasher was running, the lights come on and there is a high pitched noise. Then all the lights go off and the motor sounds like it is starting. However there is no water and the heating elemant comes on. The lights on the front; china/crystal, normal wash, clean and heated dry, all come on as if the computer is confused and trying to run them all simultaneously.


Sounds like the board was fried from a power surge ... GE Tritonr XL GSD6260JCC Dishwasher

I turn on the dishwasher and it just hums with no water spraying the dishes. I tried the sani wash cycle and it worked but just one time. Now every cycle is the same - turn it on and just the mild motor noise


... Miele 24 in. Novotronic G851SC Plus Built-In Dishwasher

Dishwasher won't drain nor will the lower arm rotate and spray. When turned to the ON position it just makes a clank noise (like a motor is trying to turn on) and hum for a short bit. Nothing afterwards. There is water standing in the basin.


I don't know if this is unusual or not. But, I found A solution. Thinking about what I said in the problem descriptor, I disconnected the power to the dishwasher. Got to messing around with the electric motor and found it was seized up...don't kno ... Hotpoint 24 in. HDA1000G Built-in Dishwasher

I have a new Ariston LKF720 dishwasher. In part of its wash cycle it is very noisy - not water noise, but a grating motor-like noise. Is there anything I can do? Is there anywhere I can watch a dishwasher do a run and listen to its noise, Ariston or other brand? We bought the present one off the floor and did not expect any problem, having had other dishwashers for years, they being quiet. The poor technician already changed the motor, but it is still just as noisy. I am even considering sellin


... Ariston Technologies L63 Free-Standing Dishwasher

My KitchenAid dishwasher (model KUD101TJWH0) suddenly is making noise from the motor area while inputing water into the unit, whether in the rinse or washing cycles but makes no noise in the draining cycles. I have pulled the unit out while still connected, cleaned any debris from the filter screen below the lower water spokes and can hear the noise very plainly by the motor but I know how sound can travel with the piping. Is the sound only coming from the electric drive motor attached to the


... KitchenAid Dishwashers

Dishwasher makes grinding noise during wash cycle (after pre-wash). noise persists for 15-20 minutes. It seems as though the inlet valve doesn't open during this phase of the cycle. adding water to the dishwasher manually eliminates the noise and water circulates through the wash arms. I'm trying to determine if this is a controller issue or a valve/pump issue.


Water-inlet valve\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\012\015\012\011\015\012 \015\012 \015\012 \015\012 \015\012 \015\012 \015\01 ... KitchenAid Dishwashers

No water my kenmore dishwasher is not getting any water. when we try to select normal wash or water miser cycle, the motor turns on, I can tell water is getting to the dishwasher because i can hear it running under the sink and feel it in the flexpipe that feeds the dishwasher. It is not getting anything inside though. Just wondering if you have any ideas. Thanks


SOUND LIKE YOU HAVE EITHER A FLOAT THAT IS STINKING OR A WATER INLET VAVLE THAT HAS FAILED. THE FOAT IS THE LITTLE MUSHROOM LIKE DOME WHICH IS PLACED AT THE FRONT LEFT SIDE UNDERNEATH THE BOTTOM RACK PULL UP GENTLY ON THE FLOAT UNTIL U HEAR A CLICK ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

Maytag diswasher MDB6600AWW Sprayer arms don't spin. Dishwasher makes all the right noises, except for spraying. Water fills properly and heats up. Water drains properly. Found paper on the back of access panel. Ran Manual Function and Field Service tests, no problems indicated. Disassembled all the pieces inside the bottom of the dishwasher. No obviously damaged parts. Shaft for motor turns freely. It seems like the parts that attach from the impeller to the motor shaft don't


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

My dishwasher is making a noise and will not drain. when I looked underneath, the thing that connects to the hoses was what was making the noise. It looks like some sort of motor and has copper coils in it. the water from the dishwasher flows to it and I guess it pushs the water on threw.


Hi,\012Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... Frigidaire 24 in. FDB1250REC Stainless Steel Built-in Dishwasher

My tappan dishwasher is only 1 1/2 yr old and its not getting at least 1/2 of dishes clean. We have tried everything from changing to liquid soap, increasing water pressure at meter, not using while washing clothes. We used a dishwasher cleaner to remove calcium, and run hot water in sink before using. We know the wand, pump and drain are working. It is model TDB210RFB5 with 1.1A motor. Is the motor too small to clean dishes? I wish I could get my money back or exchange for an upgrade. Thanks!


... Electrolux Dishwashers

I have a Maytag MDB7100AWW dishwasher that makes a lot of noise from the motor at the end of the drain cycle. When there is water in the dishwasher it doesn't make any noise and washes well. This url (http://www.applianceaid.com/maytag-dish-noise.html) describes my problem exactly but I can't remove this part. I have unscrewed the 3 screws keeping it in place but it seems to be still attached to the motor. How can I remove it?


... Maytag MDB7100AWB Dishwasher

The dishwasher is making a horrible noise. Could it be the motor? Tried running both drawers and same noise each time. About how much would it cost to replace motors? Would I be better off getting a new dishwasher?


... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Maytag HDB8600AWW Dishwasher had been making noise (thought might be water valve, like previous DW), eventually stopped draining water, water now in bottom, I've let sit for couple weeks, looked inside, water was gone, I tried running again, it filled with water, but heard humming control panel noises for first time, then shuts itself off. Also, my handle needs replaced. Please let me know as soon as possible. Thanks in advance. David Weaver


Hi David\015\012\015\012The hum and all the noise that you have mentioned in your post states that the issue is with the pump and motor assembly. Please check the drain hose and try to clean the drain pump filter for any clogs, obstructions. Af ... Dishwashers

Dishwasher will not fill with water... push start and the lights go out.. can hear motor but no water push again and the lights come on but no action inside i have tried 'cancelling; ... water is ON , door is closed.. have tried different cycles.. no kinks in hoses :(


Hi,\012Here is a tip that will help you to find out why water will not come into the dishwasher... Dishwasher ... Maytag Dishwashers

Obtained this haier hdp18pa portable dishwasher, thought I would give it a try. The unit will not fill with water, turn the power on you can hear the motor or the pump running but no water comes in. THe 4 display lights flash and beep a series of times and then stop only to repeat the sound off in a every few second sequence. I have tried the remedies offered online, tilting the unit does not seem to work for me on this one. I changed out the water inlet valve but nothing changed and I got the s


HiYou need to clean the filter that is in the tube that gets water in the dishwasherin case you can not find it pls ask me to send you a diagram ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

This problem is intermitten. Kenmore 665 16765690. starting the dishwasher, I hear a motor running. I think it is trying to empty water, however there isn't any water. I will turn the time rotor around to the start again. Sometimes, when I do this the motor running sound has stopped and I hear gurgling sound of water entering. Once this happens, the cycle is good and does well. However, there are times, rotation the timer back to the beginning may take several times, up to about 20 times.


Hiclean water filterthe presure is to lowPls vote me to keep us alive ... Kenmore Dishwashers

My Whirlpool Dishwasher ADP931 has stopped working. It stopped in the middle of the cycle with 2 to 3 inches of water on the floor of the compartment. I mopped out the water and tried to restart the dishwasher. The green "on" light now comes on when I press the start button. but nothing happens (no motor comes on,no water enters).Repeating the above action several times does not help the washer to restart even though the other function lights will come on when the knob is turned. saturn1914


Hi,Whenever you see such symptoms, Time for you to investigate it properly. Check the below guide :-\015\012\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is\015\012there power getting to the dishwa ... Dishwashers

All of a sudden, my Kenmore dishwasher (Model 363.1411691) will not cycle. When I lock it shut and try to set it to wash, all I hear is a click--no motor running, no water sounds. As I advance the timer knob, I just get clicks where each cycle should begin. There is standing water in the bottom of the dishwasher which does not drain out. Any advice would be much appreciated, for sure.


Hi.The clicks are simply the relays in the timer board that try switching on. The control module is likely working.The cycle does not start because of a different problem.If no light is coming on, then ensure that wall socket ... Dishwashers

When i turn my Viking dishwasher on the motor starts to run but no water comes out. It was humming along for several hours before i realized that nothing was really happening. I turned it of and then tried again but the same thing happened. It sound like a motor and/or pump working but no water enters the chamber. Thanks, Jonathan


It sounds like the Water Supply Solenoid is bad. I would change that and let all of us know what happens. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1730 seconds