Having problems with your Frigidaire Dishwashers ?

My frigidaire built in dishwasher runs for 4 minutes and then stops. I get flashing lights


Answers :

Repair Help & Product Troubleshooting for Frigidaire Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My frigidaire built in dishwasher runs for 4 minutes and then stops. I get flashing lights


... Frigidaire Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Hi Have a built in AEG OKO Favorit slim dishwasher (can't find exact model no). Problem is that dishwasher tablet dispenser does't open and after 5 minutes get 5 lots of 2 beeps. When I open the dishwasher, the Rinse/Hold, Intensive, and Normal lights are all flashing. Do I need to get an engineer out? Thanks


HI there,If that\015\012lever is broken or in some way defective, it will need to be replaced. As well as controlling cycle times, the timer on many\015\012dishwashers also functions as an actuator for the spring-loaded\015\0 ... Dishwashers

Asko 1585 Dishwasher. Lately the washer has not been completing it's cycle without going into the all lights flashing mode. Usually just opening the door, closing then pushing start gets it going again. Yesterday this happened and it was restarted as described, then it go stuck in what appeared to be a drain mode - all lights flashing, drain motor running. It was in this mode for several hours and could not be stopped by any means. Pushing buttons or opening the door had no effect. Even c


Hi\015\012\015\012\015\012\015\012Thanks for using FixYa. You are right it is related to a bad control board. The\015\012control board has gone faulty and needs a replacement. Please check this recall\015\012information--- ... Asko 24 in. 1585 Built-in Dishwasher

My Hoover dishwasher HFI 3015 is not working. When you turn it on, the P1 and 'out of salt' light is flashing and bleeping constantly. I believe that it may have run out of salt yesterday, but I have filled it this morning and there is plenty of Dishwasher salt in the compartment now and it is overflowing with water. I have tried turning the machine on and off, but each time I turn it on I get this bleeping and flashing and can't stop it. Any ideas?


... Hoover Dishwashers

Matsui dishwasher Matsui MS452S slimline - second wash light flashing and unit doesn't fill. Tilting it backwards allows water to leak out from the left rear corner then it runs correctly for minute or two before numerous beeps sound and unit cuts out with light flashing again. How do I get into the base to see if there are any leaks? Unit less than 2 yrs old.


... Dishwashers

Smeg Dishwasher Hello I have a smeg dishwasher - built in, push button. It has stopped working - the program start and you hear it drain but that's as far as it gets, no water appears to be getting in. A couple of times the last 2 program buttons flash or the rinse light is on when we open it. let me know if you have any thoughts on this - I'd really appreciate it. thanks Diane


Replace the timer/control board ... Dishwashers

My smeg dishwasher seems to be permanently in wash mode. The light on the menu of settings no longer flashes, but permanently is on, and when I run a load it never stops. I hear the two beeps as if the dishwasher is starting a load so it seems to be cycling through over and over. How can I fix this and get the blinking light back? Thanks


You have a timer relay issue ,probable need a new board for it ,a cheap fix would be to time it and see how long it take to run full cycle and put a regulaer outlet timer on it or a alarm off your stove or what ever,save a couple of bucks ... Smeg STX2 Dishwashers

I cannot get my dishwasher to run. It is stuck with normal and cancel lights flashing. I cannot get them to stop or it to run. What do I do?


It sounds like the main panel circuit board is messed up....it needs to be checked and replaced if necessary. ... Dishwashers

Ignis ADL347 integrated dishwasher runs for a few seconds then stops, beeps and light flashes 6 times. I'm told this is due to water not getting into the dishwasher. it was working perfectly until we had a washing machine installed, can't see any pipes that are twisted or crushed but also don't have great access to the back of the washing machine or dishwasher. I have no expertise whatsoever. What should I be checking/trying? Any advice appreciated.


... Dishwashers

Dishwasher runs but stops after 20 minutes with green flashing light.


... Kenmore 24 in. 17032 Built-in Dishwasher

Hi, we have a Hoover HEDS668-80 dishwasher at work. The first problem we had was none of the programs would run this turned out to be a broken door lock. After replacement we managed to get one pre wash and one wash program to run, now when we try it, it starts but after 2 minutes the pre-wash and wash lights flash and the machine beeps 8 times. Can anyone help?


... LG LDF6810 Built-in Dishwasher

I have a Frigidaire Professional series less than five years old. It won't run and flashes the wash, clean, and sanitize lights simultaniously. Any thoughts on what the problem is and whether it is worth fixing? This is the second Frigidaire I have had in ten years. The model number is PLD2851RDC3. Any help would be greatly appreciated before I go out and get my third dishwasher in ten years!


Hi.The two lights are not an error code, but they are telling that the machine is in failure mode.The error code is retrieved performing a water/service test.The water/service test is a special function initiated ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

Frigidaire dishwasher Model GLD2250RD50: Stopped washing dishes when a ran the garburator full of water, panel lights of high temp and nearby started flashing, then I pressed cancel/start, lights went out the washer wont run, checked breaker no problem. door latched,


... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

I have a Siemens Dishwasher. I'm not sure of the model but it is built in, has concealed controls and was purchased about 6 years ago at Best Buy. It sort of looks like the SL85. When started, it runs for a few minutes and then starts to make a horrible sound. ALmost a grinding sound but may also be like water trying to get through a small opening. The sound does not stop even after turning off the DW and even the power to it. Only turning off the water supply does it stop. Help?


... Siemens SL85A705UC 24 in. Built-in Dishwasher

Dishwasher Whirlpool ADG7540. Does not complete cycle. Approx 20 minutes into cycle dishwasher appears to get stuck on rinse.The water is cold. Machine stops and makes a constant beeping noise and the green light flashes 3 times repeatedly.


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

ADP5550 DISHWASHER RINSING LIGHT ON, START LIGHT FLASHING TWICE, BUT STUCK WILL NOT PROCEED WITH THE WASH. I HAVE PRESSED THE START BUTTON FOR 10 SECS, 30 SECS BUT THE ONLY RESPONSE IS THE PUMP ONLY RUNS FOR A FEW MINUTES AND STOPS.


This does sound like a problem with the "anti-flood" device that does detect water (leak / spill) at the base of the washer. This device is a protection device that consists of a polystirene float and a micro swithch. Once a water leak od spill is de ... Whirlpool 24 in. DU920PW Built-In Dishwasher

Have a frigidaire dishwasher (model- PLD4375RFC0)about 2 years old. Set to run as we left to go out of town- when we came back all lights flashing including error- found a child's plastic bowl that had fallen to the bottom and had a melted spot as it was next to the heating element. Called support and were told to master restart- shut the power off for 15 minutes. Did and now flashing "27". Cannot find a code for that and neither could support without sending out a repairman. Any advice before


... Frigidaire Dishwashers

I have a Whirlpool ADP6515. It's been working fine for about 2 years now but recently cycles are not completing properly, it can run for 30-40 minutes depending upon cycle. The start light is flashing a 4 times repeatedly, I think this happens when it moves from a wash to a pump cycle but not sure. We have to hold down the start button to force it to go to the end of the cycle and the the lights stop. If we do that we can then use the dishwasher the next time, but only after we force it to go to


While replacing the console board, the replacement should be of same version. The boards are using programmable IC. Hence matching the software version is a must. Only the manufacturer or his authorized provider can help regarding t ... Whirlpool Gold 24 in BuiltIn Dishwasher w Adaptive Wash Cycle 24 in Builtin Dishwasher

We have an Asco type DW 95.5 built-in, model 1885. During operation, it stops, all the lights across front panel flash. Code F2 flashes. Although stopped, something electric still runs. When I pop the circuit breaker, all is stopped. However, when power is restored, the lights and code flash as above, and, again, something electric runs. My email: [email protected] Thanks for any help...


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Based on your description " During operation, it stops, all the lights across front panel flash. Code F2 flashes. Although stopped, something electric s ... Asko Dishwashers

Runs for a few minutes then stops and the program and top right light flash, if i press the power button off then on it runs again for a while then stops again with the flashing lights.


The electronic portion of the dishwasher is going bad. Could be a resister or any other issue..I would check with the manufacture Tech support they will advise you what your options are. ... Zanussi Dishwashers

Just had new Frigidaire dishwasher installed. When cycle is started, display shows 99. Unit will fill with water, run cycle for about five minutes, stop and empty water then display a flashing PF. Can not seem to find a list of codes for this.


Pf is means power failure. ... Frigidaire 24 in. PLD3465REC Stainless Steel Built-in Dishwasher

Westinghouse SB908sl stops after 15 minutes all program lights flashing, after sometime they will go off and after I have switches off the power for a long time I can run the dishwasher again and the same will happen again.


... Dishwashers

ASKO dishwasher D3122 drain pump wont stop pumping and the machine wont respond when we press any of the program or start/stop buttons. the program light is flashing. We can turn the power off with the main switch on top of the door but when turning it back on the pump starts pumping again. please tell me how to fix this problem so we can get it up and running again.


... Asko D3122XLSS Stainless Steel Dishwasher

I have a problem with my Zanussi Aquasave ZT685 Built in, No matter what programme i choose the dishwasher starts off as normal but stops after a few minutes. When i open the door, the light above normal is flashing quickly and there is a pool of water at the bottom, Any Ideas?


Hi There - We have exactly the same problem which you describe, and wondered if you had managed to find a solution. ... Zanussi ZT485 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2712 seconds