Having problems with your Frigidaire Dishwashers ?

CHILD LOCK LIGHT IS FLASHING AND DISHWASHER WILL NOT RUN THROUGH A CYCLE.


Answers :

Repair Help & Product Troubleshooting for Frigidaire Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

CHILD LOCK LIGHT IS FLASHING AND DISHWASHER WILL NOT RUN THROUGH A CYCLE.


... Frigidaire Dishwashers

Dishwasher will not run child lock light is flashing and the timedelay 2 hour light is also flashing


... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Kitchenaid dishwasher mod#KUDS01DLSSO- runs till 54 min left on cycle in normal wash then normal light and add dish light begin to flash with 2 dashes where time should be and locks out


... KitchenAid Dishwashers

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

My kitchen aid kud 5255 hb51 dishwasher is not working...child lock light is flashing...?? cut off main to re set no help same thing is happening....child lock light flashes when i push cancel it too begins to flash


... KitchenAid Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

Dishs are coming out wet ,plus the child lock light strats flashing and the dishwasher does not complete it's cycle


If the dishwasher is not completing its cycle then you should expect the dishes will be wet.\015\012\015\012Is it doing the same thing everytime you start the wash? I am assuming you have already turned the mains off and back on a few tim ... KitchenAid KUDC25CH Dishwasher

"Lock on" light keeps flashing - cannot run dishwasher


Same issue..\015\012\015\012Other boards suggested heating element issue - but nothing very clear or compelte. ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Bosch dishwasher I have a month old Bosch dishwasher. It was stopped mid cycle. I drained the water at the bottom, but the active light keeps flashing, and when I press the start,reset button, then turn it off, it does the same thing when I turn it back on. active light keeps flashing and the wash light is on. It won't even lock the door. How do I fix this because there is no Bosch dealers here to help with the problem.


... Hotpoint 23 in. BF41 Built-in Dishwasher

The kitchenaid dishwasher (model KUDC25CHSS1) appears to have the 'child lock' engaged on the led display panel. The 'energy saver dry' light is flashing red and when I attempt to push 'cancel' it only flashes and never goes away. When I attempt to press a 'wash selection' the 'child lock' then flashes. Please help.


On my unit, I had the same problem (child lock LED on, or flashing.The cancel process of pushing anything was not possible, as a bad/stuck switch prevented any input from the control panel buttons.The underlying cause of the problem turne ... KitchenAid Dishwashers

Hi there. I'm having problems with my dishwasher. Usuaully once loaded, i push the start button, the closest green light to the start button flashes and dishwasher fills/cycle begins. Now, when i push the start button, the furthest green light from the start button flashes, you can hear the motor running but no cycle begins. No water fills the dishwasher.


... Hotpoint 23 in. BFV62 Built-in Dishwasher

Kenmore dishwasher Lock On light flashing


Holding the button for four seconds will not do it, you have to hold it until the light stops blinking and\015\012will go back to normal, normall takes more than four seconds to unlock the unit, this is something\015\012the sears repair t ... Dishwashers

Kenmore dishwasher Clean light flashes after reset goes through cycle but motor does not run then clean light comes on again.


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

I have a Whirlpool ADP6515. It's been working fine for about 2 years now but recently cycles are not completing properly, it can run for 30-40 minutes depending upon cycle. The start light is flashing a 4 times repeatedly, I think this happens when it moves from a wash to a pump cycle but not sure. We have to hold down the start button to force it to go to the end of the cycle and the the lights stop. If we do that we can then use the dishwasher the next time, but only after we force it to go to


While replacing the console board, the replacement should be of same version. The boards are using programmable IC. Hence matching the software version is a must. Only the manufacturer or his authorized provider can help regarding t ... Whirlpool Gold 24 in BuiltIn Dishwasher w Adaptive Wash Cycle 24 in Builtin Dishwasher

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

I have a Kenmore Ultra wash 665 15895 dishwasher. It will not run any cycles. Symptoms: When I first close the door, the "Quick Rinse" light is on and the number 18 is displayed. When I push any button, the "Quick Rinse" light flashes continuously. If I touch any other button, both the "Quick Rinse" and "Pots and Pans" lights flash continuously. No matter what buttons I press, the behavior is the same. I've tried turning the power off and on, same behavior. The only button that doe


\015\012HiThis may be an issue with heater circuit, door switch or wash pump. Press and hold the heated dry/air dry button for 15 seconds....After, 5 minutes check if you are still getting the same error. If yes, ... Kenmore 15899 Built-in Dishwasher

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

Electrolux dishwasher all lights blinking and wont turn on push start button either all lights flash or normal light stays on  either case the dishwasher wont run a cycle


Remove the toe kick by loosening 2 screws. There is a panel there with little lights that correspond to specific problems. The light that is on will correspond to the problem that the dishwasher has detected. Correct the problem and you should be goo ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

I just purchased the Haier HDC1804TW/TB/TS countertop dishwasher today. I have it all hooked up but it won't run a complete cycle - all lights flash which the manual indicates excessive amount of water cycle not completed...allow dishwasher to complete full cycle...ummm...i'm not keeping it from doing so...help!


... Haier 17 in. HDT18PA Built-In Dishwasher

I have a Kitchenaid Dishwasher, model KUDM01TJWH0. It runs through the washing cycle properly, but then the Rinse Only light begins to flash and it does not drain. I have tried hitting the Cancel/Override button (also tried hitting all other buttons, but they were ignored too), but it also begins to flash with the Rinse Only light together. If I unplug it, wait a few moments, plug it in and all the lights are off when it comes back on, wait a few moments and hit Cancel/Override, it empties and s


... KitchenAid Dishwashers

Our GE Triton Dishwasher, mod# GSD5620D01BB is 10 years old. A problem started two days ago where; when it runs through a normal washing cycle; it contuously beeps about every 1 second when it reaches the Drying Cycle and the LED Green light flashes next to the Drying . I reset the breaker and tried again; same thing happened as it went through the normal cycle and when it reached the Drying part; same thing happened. The dishwasher is cleaning and everything else seems to be working fine.


The drying fan and vent system seems faulty.\015\012\015\012Refer this diagram. Item 918. ... Dishwashers

Child proof lock light is on, cannot run the dishwasher


\015\012To turn off the Child Lock\015\012Press and hold ENERGY SAVER DRY for 4 seconds. The\015\012light turns off. ... KitchenAid 24 in. KUDM25SH Built-in Dishwasher

My kenmore dishwasher will run part way thru the wash cycle, stop and the hi temp and heat dry lights will flash back and forth and not do anything else. When you open the washer it will have water in it that has not pumper out. It seems that the light wash cycle will work after trying the regular or heavy wash. The washer is 1 1/2 years old. model # 587.15259402


First cut power for ten minutes by unplugging power cord or tripping circuit breaker.If that does not work try the following reset.Press in succession:High temp-air dry-high temp-air dry - High temp-air dry-high te ... Dishwashers

My frigidaire dishwahser was set to run a normal wash cycle and heat dry. It never ran, the soap is still in the holder and the lock beneath the heat dry option is lit. I'm unable to cancel or select any other options. I cannot get the dishwasher to run. Do you have a solution? I have tried holding down a number of the buttons in different combonations but still can't get the light to go out or start a wash cycle.


Looks like a number of things are happening.\015\012\015\012It would be easier if you can provide the model no. of your frigidaire dishwasher.\015\012\015\012I am assuming you have turned the mains power off and on. ... Frigidaire Dishwashers

I have a Kenwood Slimline Dishwasher KS474s for a year and it has always worked near perfectly. rn However, over the last couple of weeks the dishwasher has not been running the cycles properly (stopping half way through etc, starting the the delay timer half way through cycle), but it always sorted itself after being turned off and starting again. The trouble is now it has got worse.. when I turn it on the panel and lights on the front just flash, the delay sometimes scrolls through on it'


... Kenwood Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2560 seconds