Having problems with your Frigidaire Dishwashers ?

Not draining well. Disassembled lower sprayer down to interior pump below 3 allen screws and found no obstructions and pump blades turned OK with slight resistance only! (Felt normal for a small pump motor). Tested after re-assembly with no improvement! Any helpful suggestions? I'm a pretty handy guy with experience on other appliances, just have'nt done a dishwasher before! Thanks, Hart Terrell.


Answers :

Please provide full model number of the dishwasher.
\015\012
\015\012have you checked drain hose is clean on the kitchen sink end?
\015\012what problem do you experience with the draining? is the wash program not completed?
Repair Help & Product Troubleshooting for Frigidaire Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Not draining well. Disassembled lower sprayer down to interior pump below 3 allen screws and found no obstructions and pump blades turned OK with slight resistance only! (Felt normal for a small pump motor). Tested after re-assembly with no improvement! Any helpful suggestions? I'm a pretty handy guy with experience on other appliances, just have'nt done a dishwasher before! Thanks, Hart Terrell.


Please provide full model number of the dishwasher.\015\012\015\012have you checked drain hose is clean on the kitchen sink end?\015\012what problem do you experience with the draining? is the wash program not completed? ... Frigidaire Dishwashers

I have a bosch shv99a13uc. i rescued this from a thrift store so i am not sure of the history . i have installed it . all the controls work . it fills and trys to work it dosen't spray much and grinds like a very loud timer what tests should i do and can i get a manual that shows me ho to get the pump out. I think it sounds like something in the pump any help would be great Thanks


Hello &\015\012Welcome to FixYa\015\012\015\012Please check\015\012this video on how to clean the pump filter:\015\012\015\012 ... Bosch 24 in. SHV99A13UC Dishwasher

Howling noise Our kenmore dishwasher has a howling type noise but only while it washes, no noise when it is filling or when it is emptying. I have took it down on the inside and checked for anything that might be stopping the pump, but see nothing. Any suggestions? my husband thought it might be bushing in the motor but says it should do this also when it is pumping out. HELP.


... Kenmore 24 in. 16534 Built-in Dishwasher

Hi Everyone, I have a GE QuietPower 3 dishwasher that started leaking water from the bottom. It was a little bit at first but now its leaking a lot, I can no longer wash dishes with it. I'm pretty handy with tools but need to know what's wrong and how to fix it. Can anyone help me, I live alone and getting tired of washing dishes by hand. Thanks


Some times this problem is form the dw tilting down in front so ck the istallation and see if dw is level . and if heating element is gray you may have hard water build up and i this case use a cleaner to clean ... Dishwashers

My Teka Dishwasher DW7 80 FI does the first water intake operation, it sounds like rinsing, and the you hear the pump evacuating the water and two beeps as when it finishes the complete cycle. About 6 minutes. Then Stops. The lights that stayed on says error E8 according to the manual. I have done the suggested fix as ending the cycle manually and turning off and on the DW. I tested "many" times in various modes and the same preemptive end.


Hi.E8 is alternate washing system malfunction.The alternate washing system consists of a valve located in the underside of the appliance and connected to the impeller motor. The valve opens and closes switching spray on and of ... Dishwashers

She56c05uc bosch dishwasher won't drain. The drain and hose are not plugged. The dw makes normal sound in drain cycle. Any suggestions on how to test the pump?


... Bosch Dishwashers

Ge dishwasher im having a problem with a dishwasher in a  home i just bought....it worked fine at first, now it has basically two cycles, off and wash....it will not try to fill, or pump out, it just washes.....the model number is gsd1100g02ww.  i took out the timer assembly and  found nothing  visibly wrong...but hey, i can fill it  up  myself with water and shop vac  it  out and it works"i tell my wife" i wont  tell u what she told me in return......any help i would appreciate.


Try taking the dishwasher out so u can see the bottom, or if u cant, pull the bottom front plate off, remove the plate, ull see a pump looking peice, small with main water line hooked to it, disconnect it and pull it off, u will need to take it ... GE 25 in. Nautilus GSC3400J Free-standing Dishwasher

Our Maytag model MDB4010AWW (8 1/2 years old) is leaving food stuck on the dishes and glasses on the top rack consistently. We've run several bottles of Dishwasher Magic through in the past few weeks which has only helped the problem a little. We posted this question to a similar forum a few weeks ago, and it was suggested that the wash pump might need replacement. What's the average life expectancy of a lowend dishwasher like ours? would it be more cost effective to replace it rather than to sp


It would cost you at least the 200.00 to have it replaced since the pump cost 150.00 and you would have labor added. It should last longer than it did if that's what's wrong with it. I would first observe to see if the upper spray arm is spinning and ... Dishwashers

Folks, I have a Karcher 5.55 home water blaster that pulses at the highest pressure on the vario power spray wand. It works fine on the lower pressure settings and with the rotary spray wand. I live in a temperate climate, depressurize and drain after each use, always prime the pump, have good water supply, cleaned the filter etc etc. Any pointers on to do or test next? Any help greatly appreciated.


... Karcher Pressure Washers

Non-functional I purchased the dishwasher to replace a very old one. I plumbed and wired it exactly according to the installation instructions. When I started the machine to test it all i get is a blinking "wash cycle" light. There is no water moving, no pump noie, nothing. I pulled it back out and double checked everything and it is all in order. Any suggestions?


CHECK FOR A FAULTY WATER INLET SOLENOID ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

I have Whirlpool dishwasher DWH B00. Now it starts as normal filling water for a couple of minutes. Then it suddenly starts beeping and pumps out all the water and just contiunes to beep. This will happen in all programs. We have studied the users manual and cleansed the filters as suggested in the manual, but this doesn't help. There are now problems with the water supply. The dishwasher is not used very much, may be just twenty times. In the start it worked normally, this problem suddenly


Hello & Welcome to FixYa If the sound is coming from the bottom panel then it is the motor that has gone bad and needs replacement. However, if you hear the sound from the control then it can be due t ... Dishwashers

I have a Generac pressure washer, model #01450-0, with a Honda 5hp motor. The motor runs fine, but the pressure hose pulsates as if the pump is intermittently making pressure, and the pressure out of the sprayer is about half of what it should be. A friend suggested replacing the seals in the unloader. I bought an unloader kit, replaced everything and it still runs the same. It will build a small amount of pressure, spray for a few seconds, then the pressure dropps to almost nothing. Any help ap


Take a small diameter wire and poke thru the discharge hole of the spray head to clean out.\015\012Second time in 6 months that I had the same problem. The problem is alway in the spray head. ... Pressure Washers

Dishwasher fills but no pressure during wash, middle and upper sprayer are not moving. I cleaned trap and lines in tub - no improvement. Is pump bad, how to test? Is this worth fixing?


What I would Do :\015\0121st I would start your dishwasher and let it fill with water and when it stoped filling, I would open the door to see how much water it filled in the tub. ((( if you don't have enough water you will not get the correct ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Hi I have a Kudso1flSS1 dishwasher. I just replaced the control board and the switch board assembly, the pump is recently replaced and the filter is clean. The start button keeps flashing and the water level is always low. The DW stops running after 15 minutes and the flashing starts again...... Help!


... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Our GE model GSD4320Z00B is having a problem with the drain system. I've run the unit in the test mode and it does pump the dishwasher down. The problem is the unit does NOT pump down during a normal wash cycle. The fact that the unit works in test tells me it is not the pump. I've checked all the hoses and drain paths and there are no obstructions, again verified by the fact it works in test mode. Any test that can be used to determine the problem besides replacing parts one by one?


... GE 24 in. GSD4320Z Built-in Dishwasher

Full model number is SGS45E08GB/56 Will pump out water if you pour it in manually. Takes in water - sometimes. Main pump runs but no water flowing out of arms. Float switch is not operated and is not defective (tested off the machine). Intake solenoid valve seems to work properly (tested off the machine). Pump continues to run even if door is opened.


... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

My bosch dishwasher sgs09a15 is leaking on or from the pump assembly can i repair the pump or do i need to replace the pump motor assembly completely en which do i need


I consulted another website ... Bosch Dishwashers

DISHWASHER-GE GL613716A will not drain. re/re drain and removed restriction,food ect. it will not drain still. performed self diagnosis on front control panel as per trouble shooting information supplied with dishwasher when i bought it, all tests passed except when commanded on, the pump did not drain water from the dishwasher, i do not know if the pump came on as all test functions are perfomed at the same time for some reason, which made a bit of noise making it hard to even hear the pump. th


Hi,\015\012Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...Dishwasher Problems - Water will not drain ... Dishwashers

Karcher 2400 pressure washer with honda engine. my problem is that i've installed a new rebuild kit in the pressure pump assembly, and now, when i reinstall the assembly back on the engine, i cant even pull start the engine over. its too tight! when i loosen back on the pump assembly, i'm able to pull the engine over. what have i installed wrong from the rebuild kit??


The pump is correctly oiled and lined up on the camshaft, correct? ... Karcher 2500 PSI Pressure Washer

Assembly I recently purchased a pressure washer from Home Depot. It is rated at 3100 psi. It is a comet pump with a honda gas engine. The assembly instructions recommended that I remove the plug on the top of the pump and replace it with a vented plug that was provided. However, none of the other enclosed manuls talk about the vented plug. Am I reading the assembly insturctions correctly. Should there be a vented plug ?


HI your machine would have been delivered with a blanking plug in the pump. You will need to remove this and fit a vented pump or your pump will build up too much pressure inside. ... Comet BXD2527 Pressure Washer Pump

LG LDF6810ST had OE error. Disassembled found no obstructions blew air through and vacuumed hoses to air gap and to disposer, no obstructions. Never heard pump run when starting cycle, so replaced drain pump. Still doesn't run. Looked at the service manual, and the only other suggestion is repair circuit? Is this the circuit on the bottom right of unit or the pcb up top? Wires and connections all look fine. What else could it be. Any suggestions appreciated!


Hi,Usually my First Response to this Common Error is :-Most likely pump trap is clogged up. Access it behind small door at front. Drain water out through small hose that is there otherwise water will be all over the floor when ... LG LDF6810ST Stainless Steel Built-in Dishwasher

Fills with water, sounds like it starts to pump water then stops, then start again. It attempts to start pumping water 3 or 4 times them turns off leaving the water in the tub. I have read about the water needing to heat up for the cycle to advance. When I check the water that is left in the tub it is warm but not hot. The heating element is not hot either. I did a continuity test on the heating element and it seems to check out ok. I also did a continuity test on the red wire from the heating e


You have a wash pump problem. can be 1 of 3 things. most likely something is caught in the pump impelor if not the wash pump motor may be faulty or ceized or it could be the capacitor for the wash pump motor is faulty. you can try removing the wash p ... Maytag MDB7100AWB Dishwasher

Due to the my Indesit IDL 530 dishwasher not draining properly, I turned it onto it's left side, removed the base plate and pump and checked for blockages in the pump and associated hoses, which were all clear. However in re-assembling it I have forgotten which way round to connect the twin wire plug to the base plate. I cannot find a relevant wiring diagram online and therefore cannot tell which is the correct way around. I then guessed and re-assembled it anyway, and as you might have g


Hi.There is more than one wire going from control board to the tub. If the connector can be plugged either way without forcing it, then usually does not make any difference the way you plug this determined connector. It will be usef ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I can't get the igniter to start on north start pressure washer #157224. Fuses ok, indicator light in heat switch does not illuminate. Blower works, fuel dripping out. Cleaned fuel tank and pump and filter too! Tried jumpering past the thermostat didn't help either. Also, swapped pump and heat switches on main panel. No help!


... Pressure Washers

Hi. I have a 3 year old LG dishwasher. It will not drain. Display shows OE. I completely cleaned the drain assembly inside the DW. I checked the discharge line, it is completely clean. I disconnected the drain line from the air vent assembly at the sink and ran the DW, still will not drain. I disconnected the discharge pump wires and ran current directly, the pump works. I replaced the main control PCB, still will not drain. Please advise. Thanks


Measure the electric resistance of the Drain Motor. (Value should be 20-40 Ohms) If it is out of spec, replace it.\015\012\015\012Please reply with what worked best. Thanks! ... LG 24 in. LDF 7811 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0799 seconds