Having problems with your Frigidaire Dishwashers ?

My frigidare dishwasher runs, but the washing cycle is not working


Answers :

Make sure the machine is clean free from foreign deposit like soap, tiny particle of food, etc. check the button control for some lose connection, wire etc.
Repair Help & Product Troubleshooting for Frigidaire Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher runs for appx 14 min & stops washing half way thru wash cycle. Timer contunies to run. No drain pump out (nothing). Let dishwasher set idle for appx 1 hour and it will re-set. Set timer forward to end of wash cycle and it will complete rinse and final rinse. Then go to dry. Timer works ok.


This sounds like something is stuck in the drain pump. You can remove the inner cover to look for obstructions. You have a dual purpose motor it does the both circulating and draining. The blockage is causing it to overheat and trip the thermal prote ... Whirlpool DU840CWD Dishwasher

My frigidare dishwasher runs, but the washing cycle is not working


Make sure the machine is clean free from foreign deposit like soap, tiny particle of food, etc. check the button control for some lose connection, wire etc. ... Frigidaire Dishwashers

Dishwasher I have had above integrated dishwasher which is intermittently tripping the mains fuse. Power is getting to dishwasher and the washing cycles work until a certain point (not the same time) where a loud bang can be heard and the main fuse is tripped. Reset the main fuse and power still gets to the dishwasher and it works again. It has just started to trip the fuse when its not running any cycle (just when power is getting to it). I've checked the fuse on the spur and it looks ok. I hav


Its quite common for the interferance filter to fail on these models its situated in the base of the dishwasher connected to the mains block usually when they fail you can see black dust around it, ... Neff 24 in. S5456 Built-in Dishwasher

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

I have an equator PLS600 and I can't seem to get it to work. I have tried the WikiFix to help a stalled dishwasher, by adding water and vinegar. When I put on the wash cycle it does not run. Even with the short rinse cycle, the sprayer will not move, and the machine will just run through the cycle until it starts to drain. Please help!!! Thanks =)


Give the spray arm a spin to make sure it rotates. It should spin freely. If not, remove plastic spray arm clip, flip it over, replace it, and try again. Make sure holes in the spray arm are clear of debris. Spray arm must be clean for it to spin ... Equator 20 in. PLS600 Free-Standing Dishwasher

My kenmore dishwasher will run part way thru the wash cycle, stop and the hi temp and heat dry lights will flash back and forth and not do anything else. When you open the washer it will have water in it that has not pumper out. It seems that the light wash cycle will work after trying the regular or heavy wash. The washer is 1 1/2 years old. model # 587.15259402


First cut power for ten minutes by unplugging power cord or tripping circuit breaker.If that does not work try the following reset.Press in succession:High temp-air dry-high temp-air dry - High temp-air dry-high te ... Dishwashers

Our GE Triton Dishwasher, mod# GSD5620D01BB is 10 years old. A problem started two days ago where; when it runs through a normal washing cycle; it contuously beeps about every 1 second when it reaches the Drying Cycle and the LED Green light flashes next to the Drying . I reset the breaker and tried again; same thing happened as it went through the normal cycle and when it reached the Drying part; same thing happened. The dishwasher is cleaning and everything else seems to be working fine.


The drying fan and vent system seems faulty.\015\012\015\012Refer this diagram. Item 918. ... Dishwashers

I have a bosch SHE58C dishwasher. The cycles all work, it fills so the water line is ok, it washes, and it drains so it is not clogged. I cleaned out the sump and it is all clear. However, I think the "brain" or control module is bad. When I try to run a cycle, it does not fill. One other note is that it continues to run when the door is open. Is there a way to reset the "brain"? I've tried killing the circuit breaker


I have a similar problem with my SHE55M15UC model. I bought it last week and I had to push and hold the cancel button before it would start another cycle. If it doesn't finish the previous cycle, it will not let water in. Also, mine doesn't shutoff ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Dishwasher has been stored. Was working fine-ish for first half dozen washes. Now not starting wash. From troubleshooting in manual I'm holding down first two buttons and it's saying "End", but keeps moving back to SOAK function (17 mins) and not doing anything. Display shows whole soak cycle to run, but on holding down start button it makes no difference - doesn't beep to acknowledge and start cycle.


After bringing the unit from storage did you conduct any service on it? Did you remove any water before storing the unit? when you store a unit like this you need to totally empty the unit from everything including wate ... Smeg 24 in. DWF614SS Stainless Steel Free-standing Dishwasher

Cranky dishwasher I have to admit my wife's solution is the only one that works. Our ten-year-old Superba built-in usually starts a normal cycle part-way through, at the wash part, without filling or opening the dispenser door. Therefore the dishes come out with the soil now baked on. Closing the door, selecting normal and start results in a pump-out sound, or at least just the pump running to wash the dishes. The dishwasher ignores any cancel button push,and the light does not come on over t


You want to make sure that the dishwasher is level and secure first of all. Then I would look into the door latch assy. Sounds to me that you are not making all the latch switches when closing normally. When you are slamming it, you are making the s ... KitchenAid KUDS24SE Built-in Dishwasher

My KitchenAid Model KUDE70FXSS 2 dishwasher is new to us today and has never been used before. It was hooked up professionally, but I assumed it would work, so tonight when I tried to run it, it lights up on panel, but it won't run any cycles. It will start putting water in the machine, but then cuts off. It starts making a grinding noise underneath the machine, and it clicks like it is trying to work, but the water doesn't wash. Hmmm. Anyone know what to do?


... KitchenAid KUDE70FXSS Builtin Dishwasher

Dishwasher motor sounds like its struggeling to run. oR LIKE it's bogging down during washing cycles any and all cycles. there is water going into the washer but when washing it sounds like there is no water moving around creating the motor to work harder ........sounding like its gonna stop at any second. frigidaire d/w model#= FDB510LCS3 SERIAL==TH74378818


Try pouring water from the front. The pump has got air traps inside. This will ease your problem.Also check whether the spray arm turns freely without any obstacles. ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

Asko Dishwasher Model 1375. Detergent Dispenser does not open during the wash cycle. The door opens when you manually release the dispenser lid lever but will not work when running. No signs of something catching. I have cleaned the unit well. Have tied on all wash cycles. Any ideas? The unit 6-7 yrs old


Hi.If the drawer does not open at all, then the problem is the drawer mechanism itself or the detergent drawer switch connected to the electroni control module. In that case the door must be taken apart to test and eventually replace the ... Asko 1375 Dishwasher

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

I have a Whirlpool ADP6515. It's been working fine for about 2 years now but recently cycles are not completing properly, it can run for 30-40 minutes depending upon cycle. The start light is flashing a 4 times repeatedly, I think this happens when it moves from a wash to a pump cycle but not sure. We have to hold down the start button to force it to go to the end of the cycle and the the lights stop. If we do that we can then use the dishwasher the next time, but only after we force it to go to


While replacing the console board, the replacement should be of same version. The boards are using programmable IC. Hence matching the software version is a must. Only the manufacturer or his authorized provider can help regarding t ... Whirlpool Gold 24 in BuiltIn Dishwasher w Adaptive Wash Cycle 24 in Builtin Dishwasher

Long cycles My dishwasher (approx 7 years old) will run in the wash cycle for hours...until I physically turn the nob to "rinse"; then it will stay in that cycle until I advance the knob to the final (expel water) stage. I checked the filter and the blades - no obstructions. Also, when completed, the dishes are hot, so I know the heating element is working.


Http://www.thisoldappliance.com/library/bosch_dw_guide.pdf\012\012\012 ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Miele G868 dishwasher. It is 15 yrs old. 8 months ago the soap dispenser wouldn't close, so I got another dispenser from Miele and replaced it myself. Everything worked fine until 3 months later, when the soap dispenser did not open. After 3 restarts, it began to function as it should. Now 5 months later, the soap dispenser is not opening at all. Here are my observations: 1. Economy wash cycle should run 35 minutes but only runs 13 now. 2. Water in machine is not hot, even though I run


... Miele Dishwashers

Dishwasher runs forever - I have to manually drain it by pushing 2 buttons on front at same time - never gets to dry cycle - makes no difference what wash cycle i am in - however the rinse & hold cycle seems to work


Hello,Welcome to FixYa ... Thermador DWU244 Dishwasher

My dishwasher won't drain. It runs through the whole wash and dry cycle...and when I open it to unload the dishes the bottom is filled with standing water. None of the lines that I can see appear to be kinked, and I'm not sure what else to check. I inistalled the dishwasher myself becasue my husband was working out of town...this was about a year ago. Haven't had any problems with it until now. Thanks for any help or suggestions you're able to offer. Christine Fitzpatrick


If you hear the drain pump run after wash and rinse cycles then it is likely the problem is in the kitchen drain end. Have you got a disposal unit in the kitchen sink. Sometime it is full and causing a block.\015\012\015\012If you don't h ... Dishwashers

Our GE model GSD4320Z00B is having a problem with the drain system. I've run the unit in the test mode and it does pump the dishwasher down. The problem is the unit does NOT pump down during a normal wash cycle. The fact that the unit works in test tells me it is not the pump. I've checked all the hoses and drain paths and there are no obstructions, again verified by the fact it works in test mode. Any test that can be used to determine the problem besides replacing parts one by one?


... GE 24 in. GSD4320Z Built-in Dishwasher

The water does not run into the dishwasher, though the heating element works, and it goes through the cycle. The dishes are not getting washed. Also the ON light is not working. model number Kenmore 6651676569.


Hi,Here is a tip the will elaborate on your problem more, but the bottom line is that you need to replace that fill valve...Dishwasher ... Dishwashers

I have just moved into a new house with an Asko Dishwasher. It is not working. I program it, the icon for the cycle I have chosen lights up in red, I press start, that lights up in red, the water runs in for about 30 seconds and then nothing more happens. This happens on every wash cycle that I attempt to use. It does not appear to be on time delay as that icon does not light up. Also I have left it for a number of hours after I have tried to start it and still nothing happens. I would appreciat


... Asko Dishwashers

Noisey maytag We have a maytag quiet series 300 with the 3 racks. Just recently we have been hearing alot of noise from our dishwasher while it is in the washing and rinsing mode. We have checked the arms to make sure they are moving but doesn't seem to be a problem. Thought maybe there is a liquid that we could pour into the washer to run through it's cycle? Of course we know nothing about the inter works of a dishwasher.


Hi, i had the same problem twice and both time there was some plastic stuff in the shredder. Remove the screw in the middle and remove the cap and you will probably find some pieces near the blades. ... Maytag 24 in. MDB5651A Built-in Dishwasher

KitchenAid dishwasher KUDS24SEBL does not drain after rinse. It goes through wash cycle, drains water completely , then it fills water for rinsing, runs and after that it does not drain. Cancel does not work after that. Water is very hot inside the tuba t that time. The dishwasher needs to be left for an hour or so before the cancel button can drain the water out.


... LG LDF6810 Built-in Dishwasher

I have a GE Profile Eterna series triton dishwasher. When it gets t rinse cycle, lights go out and it keeps rinsing. Buttons stop working and it won't stop or reset. If I unlatch door and wait for hours lights may come back and allow a reset. Run through 3 rinses only -fine. wash cycle does it again.


... GE Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2295 seconds