Having problems with your Frigidaire Dishwashers ?

Hello, I have a Frigidaire FDB510, after a few minutes of running water starts pouring out of the bottom of the door.I have replaced the wiper or sweep seal at the bottom of the door, the gasket does not seem to be bad, (it actually does not wrap around the bottom of the door anyway). Am I not draining correctly i.e. float,pump, etc. I sure could use some advice. Thanks


Answers :

Ckd spray arm be sure it is not binding on something also ck for possible split in spray arm look close some are almost invisable ..when water is pushed through spray arm the seam will sometimes separate..also watch for oversuds
Repair Help & Product Troubleshooting for Frigidaire Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hello, I have a Frigidaire FDB510, after a few minutes of running water starts pouring out of the bottom of the door.I have replaced the wiper or sweep seal at the bottom of the door, the gasket does not seem to be bad, (it actually does not wrap around the bottom of the door anyway). Am I not draining correctly i.e. float,pump, etc. I sure could use some advice. Thanks


Ckd spray arm be sure it is not binding on something also ck for possible split in spray arm look close some are almost invisable ..when water is pushed through spray arm the seam will sometimes separate..also watch for oversuds ... Frigidaire Dishwashers

I have a Neff built-in dishwasher and sometimes there is a heavy leakage of water from the front right-hand side. The unit is 3-years old and there is a build up of scale around the rubber seals. The long seal at the bottom of the door seems to have receded slightly behind the metal panel on the inside of the front door. Is the seal easy to replace ?


Hello,\015\012Check the rubber seal in the bottom of the door has not perished or split,also check the bottom spray arm has not split on the ends as this will direct the spray directly onto the door,causing it to leak.\015\012\015\0 ... Neff 24 in. S5443X2 Built-in Dishwasher

How do I fit a new door gasket to a Hoover DT999 dishwasher (the short horizontal seal at the bottom of the door, not the longer one which wraps around the inside of the body of the machine)?


Well I just did this (ew!)basically it just pulls out of a slot downwards (when doors open) but there's not much space so I took out a few screws to free the door up a bit.So - sitting with the machine in front of you and door ... Hoover 24 in. DT999 Free-Standing Dishwasher

About a 3 year old maytag stainless steel inside dishwasher, not cleaning, often soap resdue on dishes or silverware, I use fresh new cascade, checked to see if washer fills with hot water, seems to up to the bottom of the door when I open durning cycle, arms go around, no obvious plugging of the screens, no junk in the foot chopper propeller, no paper or plastic or food in the jets of the arms. Motor went out on it 9 month ago and I had it replaced by appliance repair station here in Missoul


Water must be 130 Deg F to wash properly. ... Maytag Dishwashers

Dishwasher leaking Our dishwasher all of a sudden started leaking. I've taken the front panel off the door and can see exactly where. It's not a hole or anything...it's at the front, left edge of the basin, the bottom left corner at the front. It seems that right after it fills with water, it starts to leak once water is moving around inside and washing cycle starts. It is as if big waves are being pushed to the front left corner and over the lip of the basin. I don't think the water level is to


Just an idea...if i'm understanding you correctly,could the door seal be creased there or folded over by use and age to permit this to happen? cause you said nothing is missing ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Developed a leak at bottom of door. leaks onto floor. drain hose doesn't seem to be stopped up and the dishwasher drains at the end of each cycle. took both drain screens off and couldn't find any obstructions around the drain.


There may trash/ debris in the joint where the seal closes, the seal could also be misaligned or damaged/ worn. ... Kenmore Dishwashers

Kude48fxbl - brand new out-of-the-box. When put through a test cycle after installing it, water poured out of the bottom left edge of the door. This was not associated with either the water input or the discharge hose, but rather seemed to come from the interior of the washer and out under the door. The door seemed well latched, and running it with some dishes in the bottom tray (not blocking the soap dispenser) didn't help.


... KitchenAid Dishwashers

I have a Maytag DWU8250BAX and the thing leaks like crazy. I just replaced the door gasket, but that is not the problem. When I took a closer look at the door it seems as though the water is getting up and into the door through a space in the bottom of the door. It seems to me like there should be another door seal to fill a gap that sits between the door hinges. If anyone knows if there should be a seal here and then what the part number might be that would be great. Thanks!


There is an airgap under the door..it should spray up and run down the door not spray up under it..look for crack or hole in spray arm..if there is the wrong soap in it it will flood out with lots of bubbles..just have to flush it out. lastly, if you ... Dishwashers

Door leak I have a small leak between the bottom of the dishwasher door the lower service panel on the dishwashere. I did replace the seal on the inside bottom of the door along with the other parts that come with the door seal. Could there be a gasket leak around the detergent dispenser or the vent at the top of the inside of the door. I did not check the water lever as was mentioned in a previous question on water level, but the float does move up and down quite freely. Any suggestions as to w


I had my dishwasher leaking alot at the bottom of the doo,r and found out that the steam vent was very cloged with gunk. After taking the vent cover off on the inside of the door and cleaning, then putting the vent cover back on NO MORE leaking. Th ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

The detergent dispenser [Main Wash] door doesn't stay closed. It seems like there is something wrong with the latch, but we can't what. We've cleaned it, but don't know what else to try. There don't seem to be pieces missing or broken. But no matter what, when we put in the detergent [we use the cubes] the door always just pops open and the detergent ends up falling to the bottom on the dishwasher. The dishes are still getting relatively clean, but we want to solve the problem with the door


... Frigidaire FDB1200RG 24 in. Built-in Dishwasher

The insultation on the bottom of the door is wet. My repairman said water is getting behind the soap dispenser and the rubber gasket around the dispenser is hard. The dishwasher is only 4 years old. Is this possible. The insulation at the bottom of the door is wet. Oddly, this is an intermittant problem. The past two days, with a small load of dishes, there was no leak. Help!!


A reader on another forum found, after much effort, that the solution may be very simple: don't load flexible cutting boards on the right-hand side of the machine.The boards can block an outlet on that wall, presumably leading to a buildup ... Bosch Dishwashers

My GE dishwasher is leaking out the bottom of the front door. Everything seems to be sealed properly. I took the inside of the door off and couldn't find anything obvious. Is it possible to be overflowing from inside? I seems to drain properly when I manually turn it to the end of the rinse cycle. Thanks, Kip


You most likly need a new bottom door seal. Usually 3 screws down each side of the door and then two screws hold the bottom door seal in place. The bottm door seal can look fine but if its leaking out the bottom front this is the problem 99 % of the ... GE 24 in. GSD3330C Built-in Dishwasher

Code F2 I just replaced the door switch on an inoperable DD-602. My top drawer was working fine, but my bottom one has been offline for a while (door switch failed and I never got around to fixing it since I had the top). Well, my top finally failed too so I replaced both switches. Looks like everything is good on the top, but my bottom is erroring with an F2 code now. Kindof makes a thumping noise as it starts the cycle -- maybe 3-5 short thumps and then a 10 second delay, repeats. Any ideas? C


F2= \015\012The motor has not\015\012been sensed rotating\015\012\003 Foreign object has jammed the rotor\015\012\003 The rotor has failed\015\012\003 The hall sensor has failed\015\012\003 The electronic controller has ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Water comes gushing out of the bottom of the door whenever water goes in. It seems like the seal at the bottom of the door isn't doing it's job. What can I do to fix it?


... Amana 24 in. ADB1500AW Built-in Dishwasher

I have a Kenmore dishwasher model 66574362K2. It has worked fine until tonight. I opened the door before the end of a cycle, closed the door, and pushed the cancel drain button. There was still water in the bottom but the dishes were basicly finished. Now I can not seem to get the dishwasher to come back on. The lock button seems to be on and it usually is not on. The manual says to push and hold the button for 4 seconds to turn it off. I did that. But now it is flashing between the Heate


Can you press the drain button to drain the water, then shut the unit off and restart??? I have exhausted all my resources to help, thought this may work. ... Kenmore Dishwashers

We have a leak around the door. It looks like it is around the bottom of the door. We can not find any reason for this. We have checked seals and everything else we can think off at no avaiel. Model 15919. We have found pieces of black stuff on the floor like maybe a protective cover that is deteriorateing . Other then that, everything else is fine. Thanks Dan


... Kenmore 15919 Built-in Dishwasher

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

Leaking water from underneath the front door. Water seems to be leaking through the bottom plastic seal. and sprays against the inside bottom of the door then drips onto the floor. Help


Hi,Leaks under the door can stem from a variety of causes. If your\015\012dishwasher is very old, the tub itself may have become corroded and may\015\012have holes. Inspect your tub; if you see such damage, use an epoxy\015\012patch kit t ... Dishwashers

Whirlpool ADG993, door fault: Hi, a few weeks ago soemthing broke on the door to my diswasher and it falls open wide with no stopping half way as usual. That was fine as the machine could still work, but now the door won't close. All seems fine until you get all but closed and then the door raises slightly from the bottom right corner, preventing it from closing. It looks like something may be jammed in there which pushes the door up at the last minute. There's a man coming out on Friday,


... Whirlpool Dishwashers

Hi, I have a small leak at the bottom right hand corner of the door. If you push in on the door while it's running it stops and the noise level goes down. Is there an adjustment for the door or would it just be the seal, it's 4 yr. old. My wife say's that the grand kids have leaned on the door in the down position , we try to keep it up when they are around , that's why I am asking about a door adjustment. Thanks


No adjustment. Try cleanig door gasket. If still leaks hinge probably got bent from leaning on door. Or door got bent. Needs to be taken apart to find cause for problem. ... Bosch 24 in. SHE44C05UC Stainless Steel Built-in Dishwasher

Hello! I have a Kenmore Dishwasher Model # 665.15805890. The dishwasher came with the house and I'm guessing it is around 10 years old. My toddler was having a great time flipping the door to the soap dispenser back and forth until he pulled the door off of the pin. Now, I can't seem to position the spring in a way so that the door will spring back. I never looked closely at the hinge before, so I don't know if that is the only reason the door will not release the detergent, or if something


Hi.Please see if the diagram here can help you. Check if the spring is that indicated with nr ten in diagram. ... Kenmore Dishwashers

Leak around bottom door gasket


No, you don't need to remove the door to replace the gasket. It is usually a pressure fit and will just push into the alloted space. Take notice of where the originial one begins and ends before removing it. ... Frigidaire Dishwashers

When we open the dishwasher door, it produces a very loud metalicsqueeking sound- like something is rubbing or binding. The door is not catching on anything externally, and there doesn't seem to be resistance to opening or closing. I have lubricated all the external parts- pully, cable, etc, with silicon spray, but the sound continues. It is difficult to pinpoint the exact location- obviously at the bottom of door. What must I do to correct the squeeky noise? Thanks for your help!


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

There is soap left at the end of a cycle from the dispenser. It is trailing down the door and standing in a puddle at the bottom of the dishwasher. The soap that is not in the trap door seems to wash away, but not the soap that comes out once the trap door pops for the main wash. Any ideas on how to fix this or what could be causing the problem?


Try different detergent types--liquid instead of powder, capsules instead of liquid. Don't put large dishes near the door that might block spray. Check the spray holes in the spray arms for blocking. ... GE 25 in. Nautilus GSC3400J Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0889 seconds