Having problems with your Frigidaire FDB641RA Built-in Dishwasher ?

Frigidaire FDB641RAB0 will not run. lights on front panel are illuminted, but it will not run. Acts like it has no power, but obviously does.


Answers :

Repair Help & Product Troubleshooting for Frigidaire FDB641RA Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Frigidaire FDB641RAB0 will not run. lights on front panel are illuminted, but it will not run. Acts like it has no power, but obviously does.


... Frigidaire FDB641RA Built-in Dishwasher

BOSCH DISHWASHER QUIT MID CYCLE NO LIGHTS ON DISPLAY AND ACTS LIKE NO POWER. POWER INCOMING IS GOOD AND POWER TO SWITCH IS GOOD. TRIED NEW SWITCH WITH NO LUCK. MOTOR WILL RUN IF OVERFLOW FLOAT UNDER DISHWASHER IS LIFTED.


Check the sensor of the liquid at the bottom of the dishwasher. Sometimes that is the cause of the fault. ... Bosch SHU43C05 Stainless Steel Built-in Dishwasher

My GE Quiet Power III dishwasher won't dispense the soap properly. It's all clumped up around the bottom. It won't run a full cycle.  When I turn it on it lights flash and it acts like it will run but then it stops.  


... Kenmore 24 in. 16032 Built-in Dishwasher

Kenmore dishwasher... filled up with water and its lights went off.. no buttons work acts like no power. check the house fuse box - ok ... check the 2 door switch - ok .. checked the thermal fuse - ok ... so, i picked up a new board and changed it out. still wouldn't run.


Did you check power to the unit? Double check the common and grounds. When servicing I will disconect(unplug from wall) power to the unit. Is it pluged in? Use another outlet(the outlet under the sink may be wired thru a switch for a disposer)even ... Kenmore 24 in. 16032 Built-in Dishwasher

Washer will not start. acts like no power. front


... Whirlpool Dishwashers

Washer will not start. acts like no power. front


... Dishwashers

My Hotpoint diswasher suddenly stopped working last night. It seems like it has no power to it, as the motor or pump does not seem to come on at all. Obviously when I get home from work, I will check the obvious first - making sure it has power to it, connections are secure etc. (I had a wire break before) If it does have power, I would assume checking the door switch and timer is next. Any suggestions, and any suggestions for checking the door switch and timer??


Sounds like your on the right track. I would use an ohmeter to check the resistance of the door switch by placing the meter probes on each side of the switch. Test while opened and closed position. Same with timer ... Hotpoint Dishwashers

The engine starts cold after 2 or three pulls, runs ok initially, but seems to have slightly less power. After a few minutes I can turn off the choke. When teh engine warms up and runs for about 15 minutes, there is a definite power decrease and the motor sounds like it will stall. If I paly with the choke, it does not stall, but has little power to pump water. If the engine does stall or it is turned off, it will not restart until it cools down.


I would first try draining the carb bowl, if you look at where the choke lever is and look below that you should see a clear red tube with a flat head screw below that, if you just turn the screw out the carb will drain. If you still have an issue yo ... Karcher G3025OH Pressure Washer

Whirlpool dishwasher DU1015XTXBO Stopped working during cycle, acts like don't getting any power. Checked the plugin and it works. No lights or anything coming on the dishwasher. Its like it just


... Whirlpool Dishwashers

My Troybilt pressure Washer Model 020207. runs forabout 30 seconds then the motor stops. Acts like motor is locked up. Motor can't be pulled until water hose is disconnected. Took the water pump off and the 6.75 Briggs starts and runs like new. What could be the problem.


It sound like a digafame problem/or/carborater bowl has some water or needel valae is sticking cheack them if not the problem then you may have a crank shaft problem good luck see if there is oil in motor ... Briggs & Stratton Pressure Washers

I was using the washer and it was running fine for a couple of hours and then it quit like there was a current sensor or something tripping. I would turn power on and press trigger on wand and then it will run for a few seconds and then quit again. I have to turn the power swich off then on again and then it does the samething.


Your preasure regulater ,remove and clean you will be back in action ,can I borrow it to clean my shop.lol ... Northstar Electric Wet Steam & Hot Water Pressure Washer 1700 PSI

Dishwasher acts like it isn't getting power.


If you have power to the board and no power out to components then your board has failed. Will need to replace board. Part#154635501 and sugg retail is about$100. ... Dishwashers

I have a Honda GC160 5 horsepower power washer with 2400 psi. When its cold it is easy to start but after it has been running for a while the only way to start it is to have the water shooting out of the wand. Once it is hot and running if i stop the stream of water (release the trigger on the wand) then the machine shuts off. It seems like the only way to keep it running is to constantly have water running through the wand. Please help


... Pressure Washers

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

KitchenAid KUDC10IXBL - acts like it has no power, lights do not light up. Checked breaker - ok - checked it does have power going to the power supply


... KitchenAid KUDC10IXBL Builtin Dishwasher

Dishwasher would not work and clean light would blink seven times. Asked an expert and they said to hit saniwash and heated dry two times. This work for a couple of times but now the dishwasher acts like there is no electrical power goimg to it. I tested the power with a voltmeter and there is power going to the circuit board.


Normally this happens when the dishwasher electronic control does not detect a water temperature increase during the main wash cycle. The issue could be in the heater element, the thermostat or the wiring that is connected to those or on the electro ... Dishwashers

I'm trying to get a Durabuilt pressure washer (model DB1303) to work. After hooking up the water hoses I plug it in and turn on the power. It sounds like it's running but there is no increase in pressure and it runs continuously. I only let it run for about 10 seconds and then turned it off. I tried it a couple of times...no luck.


... Coleman Powermate DuraBuilt 1400 PSI Pressure Washer

GE dishwasher GLDL500N10BB (2 year old)began to run eratically 2 months ago. Would run a cycle then restart and continue like that for hours. Sometimes it would run a partiaal cycle and stop. Finally no start at all. Have dor off and no visible wiring issues, water, or other obvious issues


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. If the cycle doesn't\015\012complete, then the first thing ... GE Dishwashers

Whirlpool GU2500XTP acts like it doesn't have any power


... Whirlpool GU2400XTP Built-in Dishwasher

I have a ge profile quiet power 3 model # gsd4330z00ww, theres power to the dishwasher but its acting like theres not, no lights or buttons work.


The control board may have failed. There is no way to know the exact problem without troubleshooting with a multimeter ... GE Dishwashers

The washer will run about 2 min. then die. i have checked the oil, air filter and gas. it has good presure when running then it acts like its out of gas by stalling and dieing. Problems with Mi T M 13 Hp, Honda Ohv, Compressor, 3500 Psi 3.7 Gpm, Belt?


It is possible that the oil pressure switch is not functioning properly or you have a lighter oil in the machine than is recommended.Post a comment if you need more assistance. ... Honda Pressure Washers

Dishwasher appears to have no power - no panel lights at all (lock, start, etc). Power is 120VAC at outlet to DW when disconnected but the voltage is 60VAC at junction box under DW once it connected. Acts like a floating ground but N is 0VAC to Grnd. ??? what should I be testing / checking??


Door switch ... Jenn-Air 24 in. JDB1100AWS Built-in Dishwasher

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

My Frigidaire model FDBB2040FC3 ''acts'' like it starts running when I press start but after just a few moments the Start indicator light goes out and the Hi-Temp Wash and Air Dry lights start flashing... I can hear it ''running'' or doing something but it clearly isn't actually cleaning anything. I've tried cancelling, letting it reset itself and then restarting... even shut it off from the breaker. Each time the problem returns.


... Frigidaire Dishwashers

After a power outage, that occured while the dishwasher was running, the lights come on and there is a high pitched noise. Then all the lights go off and the motor sounds like it is starting. However there is no water and the heating elemant comes on. The lights on the front; china/crystal, normal wash, clean and heated dry, all come on as if the computer is confused and trying to run them all simultaneously.


Sounds like the board was fried from a power surge ... GE Tritonr XL GSD6260JCC Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0784 seconds