Having problems with your Frigidaire FDB956RB Built-in Dishwasher ?

I have Frigidaire FDB956RBC1 diswasher. I have to turn off the water to fix the faucet. When I turned the water back on, water did not go to the diswasher when I used it. The diswasher runs normal except with no water going into it. The water runs find at the facet. There is separate water supply underneath the sink for the faucet and the diswasher. I wonder if there is a mechanism with the dishwasher that stop the water from going into the dishwasher after the water supply been turn off. I did


Answers :

FRIDG... EXPERT HERE \012
\012\012

Welcome to fixya
\012\012

Hello
\012\012


\012\012

I have a solution for this
\012\012


\012\012

Press Ok, Accept or replay so we may get started
\012\012


\012\012

Your pre-solution is coming up shortly
\012\012


\012\012

PLEASE\012REPLY OR LEAVE COMMENT TO CONFIRM YOU RECEIVED THIS EMAIL
\012\012


\012\012

My name is Bruce

Repair Help & Product Troubleshooting for Frigidaire FDB956RB Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have Frigidaire FDB956RBC1 diswasher. I have to turn off the water to fix the faucet. When I turned the water back on, water did not go to the diswasher when I used it. The diswasher runs normal except with no water going into it. The water runs find at the facet. There is separate water supply underneath the sink for the faucet and the diswasher. I wonder if there is a mechanism with the dishwasher that stop the water from going into the dishwasher after the water supply been turn off. I did


FRIDG... EXPERT HERE \012\012\012Welcome to fixya\012\012Hello\012\012 \012\012 ... Frigidaire FDB956RB Built-in Dishwasher

I was replacing my sink faucet today and in the process turned the water off to the dishwasher. Subsequently my girlfriend ran the dishwasher without the water on! Now when I go to run the dishwasher no water comes out (meanwhile I've turned the water to the dishwasher back on). Is there some kind of reset? I accidently touched the coil in the bottom of the dishwasher just after trying to run it and it was hot. What do you recommend? Thanks. Mark


Hi,You need to investigate the following :-\015\012\015\012\015\012\015\012\015\012Drain line/air gap\015\012\015\012A\015\012clog in the drain line or air gap (if there is one) is the usual reason\015\012that a dishwas ... Kenmore Dishwashers

Maytag MDBH965AWQ I have a Maytag dishwasher model number MDBH965AWQ. A few weeks ago the clean and sanitized lights would not go off after the door had been left open for over 30 seconds. Then last week, the diswasher would shut off in mid cycle and all lights would turn off with water still in the dishwasher. Today, I noticed that I am able to open the dishwasher door while the dishwasher is running and it will continue to run like the door was never opened. Now it is starting to trip the brea


2 items in need of testing are the door switch - and the main controller board/timer unit.CLIC ... Maytag 24 in. MDBH965AW Built-in Dishwasher

Can't disconnect the dishwasher from the water supply -- the faucet starts running the moment I disconnect it. I've closed the faucet all the way (as best I can, with a plier), and it still runs.


You can turn the water off using the main water valve that is located under the sink -- this will close all water off to the dishwasher and to the faucet.\015\012\015\012c... ... Dishwashers

Asko diswasher Dishwasher will not get water. Lines all checked, water on. Pump runs even when in off. Problem started when there was a water clog in the sink next to the dishwasher, and the dishwasher backfilled with water. We used a shop vac to get the dirty water out. Next day tried to use dishwasher, runs, but no water and empying pump will not stop running. Ideas?


Check for water leaks or not draining/overfilling fault ... Asko D1776 Stainless Steel Built-in Dishwasher

I have a Bosch SHU43C05UC diswasher. Last night, I put it on before going to bed as usual. I was awakened a couple of hours later to a loud grinding sound (like a pump being run dry), and found the noise coming from the dishwasher. The display read "0" time remaining, so I opened the door and the dishes seemed clean, so I left it shut off. Tonight I have been trying to troubleshoot the problem. The dishwasher will turn on, but it will not seem to fill with water. I have verified that the


Ok well before you can do anything you must obtain a service manual, link below.\015\012\015\012http://allrepairmanuals.com/bosch ... Dishwashers

Leaking from under dishwasher. Has run great since 1996. Under counter model in manufactured home. Chnaged to drop in pellet dishwasher detergent and it ran great. There is no water inside the dishwasher circular drain. We never use the heating coil to dry the dishes. We have turned off the water supply line under the sink to the dishwasher. Cool clear water is running out from under the bottom right corner. The hot water heater is right next to it and everything is dry and warm under it which i


Hi,Depending on the model you have this could be a couple of things. The most likely suspect is the water inlet valve. What I would recommend to do is take the bottom toe panel off, typically there are either 2 or 4 screws holding this pa ... Dishwashers

My dishwasher is not quite 2yrs. old and has always worked great until now. Top rack cups and mugs still are dirty inside from coffee, lipstick, etc., glasses have spots and are cloudy, and silverware seems to have streaks and become darker. I always turn hot water on at faucet prior to running dishwasher. I have check the water faucet and it is 120 degrees. After starting the dishwasher I checked and the water is not even 100. After about 20 mins. the water was aprrox. 117 degrees. The


Hello,Welcome to FixYa,Based on your description I`d suspect a plugged wash pump.The place to start for that is to pull the pump filter, spray arm and check for food deposit, broken glass, undesolved detergent and ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

I have a ge profile quietpower 7 dishwasher. its built in.cannot find manuel and cannot find the serial number anywhere on the dishwasher..i need either your help with serial number or help with why water will not go into the dishwasher. motor runs water decided it wont go in. one day worked perfect and next day stopped working.


Hi\015\012\015\012This is often caused due to the fill valve. You can ... GE Dishwashers

Hi. I have a Siemens SE65E331GB Built in Dishwasher with an aquastop system. The problem is that it seems to be stuck at the end of a cycle. The pump is constantly running when stitched on. I won't top after a reset and it continues to run even if you open the door. The water supply light also comes on indicating that there is no water getting to the machine. I have tried resetting the aquastop as per the advice in other threads. This has helped in that the water supply light now stays


... Siemens Dishwashers

Whirlpool Dishwasher GU2548XTP- Dishes still dirty after it has run, especially the top rack. 5 (?) yrs old. Runs and grinds intermittently, no water seen under unit. Sometimes I add more water when it grinds, then it runs very quiet. Sometimes it doesn't seem to fill enough. Water supply good, inlet screen inspected not clogged. Not a lot of pressure shooting the water around the inside of the unit, as the detergent that bleeds through the slotted half of the detergent flip door isn't r


The inlet valve is OK, therefore the control board was not the problem. The impeller pump is noisy and inefficient, and must be replaced.Here is the part: ... Dishwashers

Water is not going into my dishwasher --worked for 13 months fine and now having a problem. When I turn it on the motor runs and rattles - louder than before, but no water is going into the dishwasher. We did nothing different and have not changed anything.


Try running a diagnostic run on the washer. Push heated dry, normal, heated dry, normal on your cycle selection panel. After you push that sequence all the lights will light up and then it will go through a test run. This fixed my washer that had the ... Whirlpool DU1055XTS Built-in Dishwasher

My Bosch dishwasher runs long. I notice the water in the bottom isn't very hot. (I've turned on the faucet and let the hot water run before I started dishwasher.).


Hello,Welcome to FixYa. ... Bosch Dishwashers

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

Water dose not go into dishwasher, it will keep running but no water is going into the dishwasher at all.


Make sure water is available to dishwasher. You will need to remove the front lower panel, and SLOWLY loosen the water supply line to the dishwasher. Place a shallow pan under the line to catch the water. \015\012\015\012If water is pre ... Dishwashers

Our GE Profile Dishwasher is not working since today afternoon. The electronics seem to be working fine but the water supply does not start on pressing the start button. The dishwasher seems to go on with its cleaning cycle without water. We don't know how to fix this or to even check any plumbing/water supply problems. Please help.


OK First try this below....\015\012\015\012Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hu ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have a JennAire jdb1090aws dishwasher. It's about 4 years old. The symptom is no water flowing through dishwasher. Approx 3 months after installation, the same symptom occurred. Tech resolved with float switch adjustment (no charge). Has run fine every since. I have not checked water supply, but doubt this is the problem (new water heater 3 months ago, sediment gone). I suspect the float switch is bad or out of adjustment. How do I trouble shoot float switch in dishwasher? Connect ohm mete


Hi,The procedure to test the float switch :-http://www.partselect.com/dishwasher+test-float-switch+repair.htmMost for no water entering the dishwasher, there are 2 main causes. One is the float switch and the other ... Jenn-Air 24 in. JDB1100AW Built-in Dishwasher

Dishwasher confused Dishwasher was switched off just after cycle commenced (tablet had been released). On restarting dishwasher, it wouldn't take in water and has just been going through the motions of the cycle without anything happening. Even when the power button on the machine is switched off or the door is opened, the motor continues to run but without water. Water is definitely switched on under sink. I think the computer is confused - can you please help?


I suspect this is nothing to do with switching off during the cycle.take the bottom plate off and check if there is water leaked into the bottom pan. alternatively, if you can, tilt the machine back to 45deg and see if water runs out.most ... Dishwashers

LG dishwasher I have just installed an LG dishwasher. When I try to run the dishwasher it sounds as if it is getting no water. I checked the water supply line twice, and nothing is blocking it. The line is attached to the hot water under the sink and is open.


I bought a stainless steel Lg less than 15 months ago for 800.00and it stopped working. The manufacture said so sorry even though you didn't take delivery until the end of Jan. your warranty goes by purchase date. I would of been better of with a may ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Water is not filling into dishwasher. Everything sounds like it is running ok and water supply is on.


Go to the back of the machine, where the main water inlet connects. The connection there is the inlet valve that should open when you switch the machine on. Usually you have to remove the machine outer casing to get to the valve. The valves are quite ... Dishwashers

My Bosch diswasher is hanging up in the cycle (at 102 mins. in normal cycle and 38 mins in quick cycle). I hear what sounds like a one second pumping of water into the sink area, a pause, and then another one second pumping of water, on and on, but there's no progression beyond this point. One possible cause: a few weeks ago someone turned off the hot water at the heater and another person tried to run the dishwasher. The dishwasher did not function because it could not get hot water. Perhaps


Hi\015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. To start with check the water inlet valve which is located\015\012behind the lower access panel on the left or right side of the Di ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Problem: dishwasher (moel MDB6601AWW) will not run. The front panel has a light, between the "Delay 1-9" and "heated dry" buttons, and adjacent to small printed icon (looks like a tombstone with the number 3 inside). Last weekedn I shut off all the water in order to change a faucet, including the hot water feed to the washer. Now the fed to the washer is somewhat frozen -- I can only open it 1/8 turn. So, I wonder if my wife tried to run the machin with no water flow, and it shut itself dow


... Maytag 24 in. MDBH955AW Built-in Dishwasher

I have a Bosch Dishwasher, Model Number SHX46L, Serial Number 860200524 that is no working properly. After running a cycle, it did not pump out all of the water, though the water is very clear, and the dishwasher does not display that there is any electricity going to it. I have verified the is 120 Volts AC at the appliance junction box. However the dishwasher will not turn on, and no lights will come on? Do you have any suggestions? I would appreciate it if you would let me know what you


... Bosch SHX46L1xUC Dishwasher

Dishwasher continually beeping midcycle. Open washer - dishes wet, water in bottom of dishwasher and water faucet sign illuminated. Can anyone advise what's going on? Just checked the water valve to make sure it was open. Thanks.


... Thermador DWHD630GPR Builtin Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1836 seconds