Having problems with your Frigidaire FGHD2433KF Builtin Dishwasher ?

PF, high temp wash and air dry lights blinking. Reset main breaker but no help.


Answers :

Hello babe_dog01 - PF typically appears in window when dishwasher is first installed, or when power has been interrupted. HI-TEMP WASH, SANITIZE and START/CANCEL backlighting will also flash. To clear, touch START/CANCEL pad or resetting the unit by unplugging it or flipping the household circuit breaker off. Wait approximately ten minutes. Since you have already done so and it was ineffective contact a professional to move forward accurately. Dishwasher could possibly be experiencing a communication error, wiring failure or faulty control board.

Repair Help & Product Troubleshooting for Frigidaire FGHD2433KF Builtin Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

PF, high temp wash and air dry lights blinking. Reset main breaker but no help.


Hello babe_dog01 - PF typically appears in window when dishwasher is first installed, or when power has been interrupted. HI-TEMP WASH, SANITIZE and START/CANCEL backlighting will also flash. To clear, touch START/CANCEL pad or resetting the unit ... Frigidaire FGHD2433KF Builtin Dishwasher

We have a whirlpool quiet partner iii. It was working fine and was opened mid cycle. Then it wouldnt drain. Then all the lights started blinking. At some point it drained the water out. We flipped the breaker and now just the normal cycle light is flashing. Flipped breaker again that didnt work. Tried the reset code hi temp wash and heated dry. Normal light still blinking. Help please?


See this causes and fix it. God bles you\012 \012 \012 \012 \012 Check Fault Codes\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Dishwashers

I tried to turn my washer on and the lights keep blinking and it won't start. I tried flipping the breaker and even left it off for a time. when I turned the breaker back on the high temp wash and the air dry lights were blinking.


... Frigidaire 24 in. GLD2150RCC Built-in Dishwasher

My Frigidaire Dishwasher PLD4375RFC is showing 3 blinking lights at the same time when I flipped the power at the circuit breaker off-on: High Temp Wash, Air Dry on the touch pad and PF on the display. It would not respond to anything that I tried. All blinking lights are off and machine does nothing when I open and close the door. Flipped the circuit breaker off-on again to repeat the sequence. I replaced the controller board, as recommended by the appliance guy since he checked and said ele


... Frigidaire PLD4375RFC Dishwasher

My Frigidaire model GLD2155RDC1, installed in 2007, stopped working after we lost power. When we flipped the circut breaker back on the lights for Air Dry and High Temp Wash started blinking, but none of the other buttons work and when we open the door these lights stop flashing and there is no power for our machine. We tried tripping the breaker a few more times and it kept doing the same thing.


... Frigidaire Dishwashers

Kenmore Dishwasher Model 665.11643300 Cycle will not run. Normal Wash light blinking Cancel light will also blink (but can be cancelled by holding button down) I tried shutting down the power and resetting at the breaker. I tried other buttons like Air Dry, etc to see if there was some sort of sequence Note* last cycle ran was rinse cycle many months ago - house has been vacant and dishwasher has not been in use.


I will look a bit further in detail about your dishwasher problem. I am assuming you have checked the inlet water tap to the dishwasher is turned on. ... Dishwashers

Nearly all the wash lights are blinking, the keypad won't respond and resetting by turning off the breaker didn't help. It just started blinking in the middle of a cycle.


Sorry to read about your problem, I hope this helps you out.Sounds like you have a general board/control failure, Their is nothing you can to to reset this issue.You may want to contact a service company. I tried to help ... Kenmore Dishwashers

My Frigidaire model FDBB2040FC3 "acts" like it starts running when I press start but after just a few moments the Start indicator light goes out and the Hi-Temp Wash and Air Dry lights start flashing... I can hear it "running" or doing something but it clearly isn't actually cleaning anything. I've tried cancelling, letting it reset itself and then restarting... even shut it off from the breaker. Each time the problem returns. We're a family of 6 so our dishwasher is pretty important in this hou


... Frigidaire Dishwashers

My Frigidaire model FDBB2040FC3 ''acts'' like it starts running when I press start but after just a few moments the Start indicator light goes out and the Hi-Temp Wash and Air Dry lights start flashing... I can hear it ''running'' or doing something but it clearly isn't actually cleaning anything. I've tried cancelling, letting it reset itself and then restarting... even shut it off from the breaker. Each time the problem returns.


... Frigidaire Dishwashers

3 sec light on control panel blinks .. dishwasher wont star. None of the other control lights come on. I have reset the breaker in the main panel to attempt to reset any internal breakers with no results. When I attempt to set anuy of the options, the 3sec light blinks then returns to a solid light.


Go to maytag website they have all kinds of help there ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

I have a Kenmore ultra wash quiet guard 3 dishwasher with a Hi Temp Wash that won't stop flashing. I've tried shutting off the circuit breaker and every code button sequence I can find including pressing Hi temp wash, heated dry, hi temp wash, heated dry...but it won't stop blinking..always blinking...Anyone have any other suggestions to reset this?


... Kenmore 24 in. 17019 Built-in Dishwasher

I have a Sears Kenmore Elite Ultra dishwasher 665.1315 model. For the last 3 weeks, it keeps having the clean light blinking 6 times pause then 1 blink and pause and repeats cycle again. I have turned off the breaker...I have reset by pressing the heated dry and normal wash until all lights are flashing. It then completes some type of cycle and looks ok. When I opened the door, steam came out and all was hot inside. However, once I try any new wash cycle, it seems to wash but after 1-2 hours and


Call sears service and tell them you need service there is a service flash and will be no charge ... Kenmore 24 in. 15932 Built-in Dishwasher

My Kenmore Dishwasher 665.16359301 quit working. I flipped off the breaker then back on again. The cancel light comes on and it sounds like its going to drain but theres no water in it. After about 20 seconds it stops and the normal wash cycle light starts blinking. Thats it. I did the reset procedure and it started to work then went back to the normal wash light blinking.


... Kenmore Dishwashers

GE GSD5320 seemed to finish all light wash cycles. Then it began to beep, with the NORMAL light blinking. I hit RESET, but none of the other buttons worked. I threw the circuit breaker for this appliance and waited an hour. I Turned the circuit breaker on but now I get the NORMAL light blinking, even when the door latch is not engaged. No buttons work.


... GE GSD5320DBB Dishwasher

FDB834RFS0 FRIGIDEAIRE DISHWASHING M# FDB834RFS0 Precision Wash System.... All control panel blinking.... Main power turn of and repower then ONLY HI TEMP WASH and NO HEAT DRY LIGHT ON. How do I enter control panel mode to clear blinking lights? Could it be faulty element inside dishwasher? Any suggestions gladly appreciated. Tks .. AA


... Frigidaire Dishwashers

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

I have a model FDB2310LCC2 dishwasher and it won't turn on. The column cycle lights washing cleaning drying and sanitizing are all blinking simultaneously along with the "high temp wash" light. I de-energized the circuit breaker for approx. 1 minute then re-energized and no difference is noted. Any ideas?


This may be a problem with the door interlock switches. You will need to shut off power to the dishwasher, unscrew the control panel and remove the wires to the door switch ( make note of where the wires go on the switches) and check the switches wit ... Dishwashers

Kitchenaid Superba (model # KUDS01FLBL6). The light by the control lock/sanitized/clean on the control panel keeps blinking. I called Kitchenaid and they recommended turning off the circuit breaker. I did this for 5 minutes and the light is still blinking. Washer won't run. Help!! Family is in for Christmas and I can't wash everything by hand...I'll never leave the kitchen!


... Dishwashers

I have a Kitchenaid Dishwasher Model #KUDI01FLBL6. The heavy wash light is blinking on it. If I hit cancel, all the lights start blinking on the panel. I have replaced the control panel part #8564542 on it and it's still doing the same thing. The tech sheet is missing on it so I'm not sure if I should reset or how to do a diagnostic on it. Can you help with telling me what to do?


HI. The control board was actually not the issue here. The interface will be the lone culprit in this case. There is a stuck circuit or button that is causing this warning(blinking lights). The button is mounted on the interface and you will need to, ... KitchenAid 24 in. KUDI01FL - Multiple Color Built-in Dishwasher

Kenmore ultra wash quiet guard dishwasher, the pots and pans and the normal wash button are blinking. The start and cancel and smart wash out tons have a faint light glowing. Thoughts? I tried the sequence of pressing heated dry, normal wash, heated dry, normal wash and that did nothing. I've flipped the breaker too. I was in process of taking it apart to clean filter, thinking that would help, but lost my manual and now I can't get that off to flea either:(. Sig


... Kenmore 24 in. 15689 Built-in Dishwasher

Control Panel won't let me hit the start button. The dishwasher is a little over a year old and is used at most once a week. The blue light on the bottom right of the dishwasher seems to no longer light up. The control panel will let me select the wash, but the start button and time indicator does not light up. Not sure if this a real defect and if just a simple exchange of the front control panel will fix the problem? Already tried resetting the circuit breaker and that did not help. Than


... Dacor Epicure ED24 Stainless Steel Builtin Dishwasher

We have a Kenmore Elite Dishwasher #665.1646 - 5yrs old. On Friday nite, there were no problems but last nite the lights would not go on when cycles were pressed ( or Start). Checked the circuit breaker and it was OK. There is nothig caught in the bottom and the overfill float is functioning. I pressed Hi-temp and Air dry alternately and all the lights lit. I pressed Smart Wash, then Start and it did not go on. I can hear it draining but no water seems to flow and then it stops. All light t


The thermal fuse on the control panel. There isa couple of wires that lead up to a white box with the fuse in it. Thatis the problem. If you are good with a volt meter or light and youplace it across the fuse, if it is bad the light will light ... Kenmore Dishwashers

Kenmore Ultra Wash, Smart Wash light blinking red.


... Kenmore 24 in. 16532 - Multiple Color Built-in Dishwasher

Dishwasher wont turn on dwa73a Amana built in. I turned off circuit breaker and now there's blinking lights on the air temp and water temp. Never use these buttons. I can't get any button to work much less get it turned on.


Hi\015\012\015\012You will have to first check/test the door latch assembly,\015\012if that is fine and the door is closing properly then it means that the control\015\012board is bad and should be replaced. Hope this helps...please post ... Amana 24 in. DWA73A Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1889 seconds