Having problems with your Frigidaire GLD2445RF Built-in Dishwasher ?

My 1.5 year old dishwasher has started to be more noisy, with a rapid clicking, such as playing card in the spoke of a bicycle wheel going very fast. It seems to work ok, but is too noisy to have on while in the room these days.


Answers :

Repair Help & Product Troubleshooting for Frigidaire GLD2445RF Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My 1.5 year old dishwasher has started to be more noisy, with a rapid clicking, such as playing card in the spoke of a bicycle wheel going very fast. It seems to work ok, but is too noisy to have on while in the room these days.


... Frigidaire GLD2445RF Built-in Dishwasher

Dishwasher beeps constantly and gives fault code that the flood switch has been activated. Neither drawer will trun off. It seems the fan keeps going, and is very noisy. It worked fine last night.


Hello there:here is some ideas that will help you clean off the flood switch thatis causing the error first unplug the power going to the machine If you by accident overloaded the top drawer\015\012and this will allow water to ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

Our GE Profile Dishwasher is not working since today afternoon. The electronics seem to be working fine but the water supply does not start on pressing the start button. The dishwasher seems to go on with its cleaning cycle without water. We don't know how to fix this or to even check any plumbing/water supply problems. Please help.


OK First try this below....\015\012\015\012Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hu ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Hi I went away on holiday and my dishwasher AEG 50800 was in perfect order. When I came back after three weeks it does not work. It was not in use while I was away so I don't get how come it is not working now .It does start up but its like the pump is just not kicking in. Ihear water running but the blades dont move and nothing seems to get washed, any ideas. Or is a new expensive pump my only option? My Husband seems to think a seal might have gone. Can a seal go while not in use? Thanks


It's worth looking under the machine. There is an overflow area with a float switch which sometimes fills up and it stops it working ... AEG Dishwashers

Whirlpool dishwasher The dishwasher works off and on. Every few days it stops going on altogether...only the cancel button goes on and the the dishwasher's timer says 2 minutes. Sometimes the air dry button works,but none of the other buttons work. The problem has been when the repair person comes out, it all of a sudden starts to work and so he can't diagnose the problem. I spoke with someone who said it sounds like with the touch pad or computer control board is bad. You don't seem to list my


Hi there,\015\012\015\012your problem is intermittent and before you start replacing parts, i would recommend that you do these checks:\015\012\015\012unplug the dishwasher from the wall\015\012check the connection betwe ... Dishwashers

Whirlpool dishwasher The dishwasher works off and on. Every few days it stops going on altogether...only the cancel button goes on and the the dishwasher's timer says 2 minutes. Sometimes the air dry button works,but none of the other buttons work. The problem has been when the repair person comes out, it all of a sudden starts to work and so he can't diagnose the problem. I spoke with someone who said it sounds like with the touch pad or computer control board is bad. You don't seem to list my


THE TECH WHO CAME TO FIX MY DISHWASHER FROM Y=THIS EXACT PROBLEM TOLD ME THAT IT IS CAUSED BY THE WATER THAT TAKES TOO MUCH TIME TO GET WARM, SO YOU HAVE TO MAKE SURE THE WATER IS NOT GOING TO BE COLD BEFORE YOU TURN THE DISHWASHER ON. AS TO FIXING I ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

My dishwasher only fills half way and it dosn't go through the wash cycle. It pumps the water out and then go to the rinse cycle but has the same problems with the water level. We have checked the motor, pump and the water valve. It seems to be working fine. Thought it might be the timer.


Hi,\015\012\015\012This is an issue with the wash motor..\015\012There are two motors,a wash motor and a drain pump/motor assy\015\012The wah motoe must have been the issue with the case.Changing the wash motor will solve your ... Dishwashers

The unit goes through its cycles but the top rack is not getting clean. The bottom spray wheel works, the middle and top spray arms are getting water but it seems not enough to make them rotate. The pump screens are clear and there seems to be enough water. Whats going on?


The problem is likely to be that the jets in the rotor arm are blocked.\012\012To check this, remove the arm (it is easy to do, as it is intended for the user to do this) and clean out all the holes. Try running water from you tap through ... Dishwashers

Hotpoint Dishwasher Bought it new 2 weeks ago. Seemed to be working ok. Last night it started leaking out the front door (suds). I disconnected the drain line (tried to blow through line to tub, NO GO) so I started it and ran it into the sink. It seemed to be flowing OK, but there is still about 1/2 inch of water inside washer. Is this OK? Model # HDA3400G02BB


Water will not come on. started 3 months ago being erratic, some time it would work, some time it would not. Now it has gotten solid. Everything runs except water, therefore no wash. ... Dishwashers

Hi, I've got a GE dishwasher (model GSD3207P00WW) which is making a horrible grinding noise... it still seems to work, however, it's loud enough that my girlfriend is terrified the machine is going to explode/light on fire/burn the house down/etc... It seems to happen intermittently (although lately it's been worse) and generally only goes on for about 2 minutes, around 2-3 times during each cycle. Any ideas?


I am not able to see the suggestions made by the other fixya consultants but I would suggest the best bet is to open the pump motor assembly (item 310) in ... Maytag Dishwasher

I have a Bosch dishwasher (SMI5072), bought in 2005 second-hand but working OK. It has always been a little slow to get going, and I had initially thought the clockwork program dial was getting stuck. Then I concluded that it had something to do with the filling up process, and I thought it must be because the water was rather cold and paid no more attention to it. This has meant that it seemingly takes ages to get through a cycle. Yesterday I put it on, left it and got on with some work. An h


There is a screen inside your water inlet valve that may be clogged. You will need to see if you are getting power to the water inlet valve when the machine calls for water. If you have power replace the water inlet valve ( not uncommon in older Bosc ... Dishwashers

Hello, We have a Candy Diswater that is just arround 2 years old. When it starts it takes water and then you hear the washer going into loop. It tries to do something els but doesn't seem so. If you open the door you can see water inside but no progress or heating. If you also try to change the program it doesn't change as well. Before it got to this point sometimes we used to unplug the power and tunr it off and then ON and then it works. However, now this procedure is not working an


Quite possibly could be the timer and could also be the main control board as well. Sometimes unpluging it will help for short times but if a serious problem persists it will only be a temp fix... ... Dishwashers

Washer went dead. replaced thermal fuse and it worked for about a week and went dead again. Before going dead it seemed to take it a long time to do a load of dishes. The last load ran 1 1/2 hours and still showed 45 minutes to go on the timer before it quit completely. Any ideas?


Sounds like you have a bad control board on unit.and the reason the thermal fuse went out is one of the relays are getting stuck on unit. before long the fuse will go bad again when the resistance level gets to high again. i would replace the control ... KitchenAid 24 in. KUDP01DL Built-in Dishwasher

When I first contacted you, I couldn't get the soap door to close in my dishwasher. As suggested I got the part. I now have the door apart. When I work the soap latch I can't see what closes the door. The part I was going to replace seems to be working correctly. over


Well IF the piece, the latch, seems to be working OK, then the only other thing it can be, is the Electronic "Drive" from the controller board, or a disconnection between the Controller and the Latch, Sometimes it can be a "Sensor" not allowing the ... Dishwashers

I have a neff dishwasher that is maybe 5 years old. im pretty sure there is nothing wrong with it as it was working perfectly fine before i had a plumbing problem a few days ago. after the plumbing problem was fixed the dishwasher doesnt seem to want to fill any longer. it sounds like it wants to work but its just not filling and going thru the cycle. does it just need to be reset or something? im not sure of the model number as ive misplaced the directions for it. could you please help? by the


Look for the connection from the valve to the inlet of diswasher. Check the hot water valve to be on. It is probably closed when anyone working on the plumping. Good luck. ... Neff 24 in. S5443X2 Built-in Dishwasher

I have a Hot Point dishwasher. Model HDA499M-02. When I turn the knob it seems like it is going to start up. But then it stops and will not work. I gave up on it and then a few days later it worked again. And when I tried to use it again it did the same thing as before.


... Hotpoint Dishwashers

My Miele Platnum dishwasher is not working. It is flashing "intake/drain" When it begins instead of the normal hearing of water moving around you just hear a humming. My husband and father took out all the filters/baskets etc and made sure everything was cleaned out. They checked the hoses. After that it seemed like it was going to work because it started to cycle normally but now it is flashing again and this time there was water standing in the bottom of the dishwasher. Any thoughts?


Most common faults with dishwashers is a drain fault. Check for any kinked hoses and check the drain spigot under the sink where the drain hose connects into the u bend. Usually this is where food gets trapped due to the spigot not being drille ... Miele 23 in. Novotronic G841 Built-In Dishwasher

GLD6200 NOISY We have above unit approx. 2 years. It just started having a "rumbling noise" when running (all cycles}. The floor even vibrates mildly. It works fine just annoying - it used to be very quiet. Everything I know how to check seems fine. Do I need a repairman ?


The sound is almost always caused by a worn docking cone “O” ring on the main conduit. When the docking cone “O” ring wears, the mid level spray arm conduit is no longer constrained and it can vibrate against the docking cone, ... GE 24 in. GLD6200L Built-in Dishwasher

Creda 47918 - quick wash works OK all 3 other programmes display 99 in the LED for time programme takes. Seems to start filling etc but doesnt go throught cycle. Any ideas


... Dishwashers

HI I AM [FED FED} UP WASHING MY DISHES BY HAND DONE A CONTINUIETY TEST ON MY FLAVEL DWFA20S AND THE ELEMENT SEEMS TO BE WORKING THERE IS NO POWER GOING TO THE ELEMENT CAN A NY BODY HELP HELP FROM A DISTRAUGHT WOMAN IN IRELAND


Find a distraught man in Ireland that knows how to fix dishwashers(grin):) You can Google your unit for 'support'. I use Repairclinic.com, but your unit may operate on different voltage from us here in the colonies. Always be aware that 220 comes in ... Bosch 24 in. SHU43 Built-in Dishwasher

OE Error I'm getting an OE error which is a drainage trouble error. I checked the hose and the drain, and everything is clear. My diswhwasher runs 98% of its full cycle and usually with 2 minutes to go I get this error. I have 2 opinins as to why this is happeneing. 1. Maybe the clog is in my trash compactor, however that seems to be working fine and my sink is funning with no slow down. 2. My 2nd theory is I have to reset the progam within the dishwasher. Like how sometimes I


Had the same problem and had the pump replaced ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

We just reinstalled our dishwasher and there doesn't seem to be any power. The current going to the dishwasher is fine just nothing happening. No buttons are working no light on the display. Help!


DO U HAVE A MODEL # AND MAKE ? ... Dishwashers

Making a loud noise like it's stuck while going through the wash cycle....can't seem to get the inner workings of it unbolted...


If the washer is making loud noise then there might be two reasons:\015\0121.The Bearings of the spinning assembly went bad.\015\0122.There might be some garbage and needs cleaning. ... Kenmore Dishwashers

Washer(Hygena) seems to leave a mist on glasses.I dont think the salt is going in properly! by what means does salt get into washer from container, how can i check that it is working properly. M whitcher


... Dishwashers

Hotpoint LFT114 Fully intergrated dishwasher. Hi I've just installed this machine and I find it very noisy compared to our old one. Everything seems to be working OK and dishes come out clean but can't explain the noise


Hi! noises can be very elusive, but some more info might give me enough to narrow down your search or figure out if what you are hearing is normal. First, what dishwasher did you have before? The noise that you are hearing, is it during the fill cycl ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1176 seconds