Having problems with your Frigidaire PLD4375RFC Dishwasher ?

Have error message which displays "ER" the " uo"

\015 Dishwasher does not wash. displays "ER" then flashes "uo" The model no. is PLD4375RFC1\015

Answers :

Repair Help & Product Troubleshooting for Frigidaire PLD4375RFC Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will c ... Dishwashers

Hi There, I have a F&P 918td dishwasher which has stopped working. Whenever I press any of the buttons I get 5 very quick beeps and then nothing - no error message, nothing the display is blank. If I turn it off at the wall and then back on again the display briefly shows two characters that do not show up in the manual as valid errors. Any ideas anyone?


Sounds like a fried board. ... Dishwashers

I have a Miele G 2470 scvi dishwasher. Machine displays F24 in display, lights flash, machine beeps and it won't run. Miele manuals seem to have no reference at all to error message displays. any thoughts?


... Miele Dishwashers

Kenmore 665.15912001 DISHWASHER RUNS BUT DISPLAYS ERROR MESSAGE Instead of displaying the number of minutes in the cycle when I push the cycle selector button and then the start button, it starts as soon as I push the cycle selector, without waiting for me to push start; meanwhile, it displays "_J" instead of the number of minutes in the cycle. It washes the dishes but not well, lots of food debris. Some people in this forum have described running a diagnostic on this machine; how do you do that


... Kenmore 15912 Built-in Dishwasher

My Miele Dishwasher (Excella Series G 2630 SCi) fails to fill. I get the message "Water inlet - Open the stopcock". I checked the water inlet filter and looked for hose kinks to no avail. I even checked the non-return valve. When I start the dishwasher I can hear a low hum (Not the pump) for a few second before the error message displays.


... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

Suddenly, an error message appeared on the display of my Frigidaire gallery series dishwasher, model number GLD3450RDS0. On advice from Electrolux customer service, we cut off the power supply for one minute. When we turned the power back on, the display read PF (for power failure), but then it went completely black. Any advice?


... Frigidaire Dishwashers

My brand new Samsung dishwasher today is displaying a 6E error message which my manual says is a functional error. It says to try to turn off the dishwasher and try to start it again. I seem to be unable to do this. HELP!


... Dishwashers

Rosieres LVI 980A dishwasher displays error message 'E1' implying water supply is switched off - but it isn't. After a week or so it works normally and then after one wash displays E1 again. Any ideas?


... Dishwashers

I have a Thermador dishwasher # dwhd650gfp with displayed error code 2, I verified oily residue on dishes and caked up grease on sump trap filter. This unit is 14 months old. I first reckognized that the dishes were not drying completely after cycle, then noticed the cold grease accumulation in drain area, then saw "E02" displayed on message board. I have read through some blogs that this issue could be a defective heater assembly, shorted or open circuit at the connection at the control pan


Hello,Welcome to FixYa. \015\012\015\012You would've been correct in your suspicion , of Bosch built dishwashers prior to this more recent revisions ... Dishwashers

Hi my Lg stainless steel diswasher wont work and is displaying a e4 error message


... LG 24 in. LDF 7811 Built-in Dishwasher

Have error message which displays "ER" the " uo"


... Frigidaire PLD4375RFC Dishwasher

Bottom draw displaying U1 error message - Fisher and Paykel 24 in. DD603H W Built-in Dishwasher


There is no water coming to the drawer.\015\012\015\012This could be due to several reasons. The tap must be on as I presume the top drawer is working.\015\012\015\012Could be one or more issues like Inlet solenoid,controller ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

There is an error message of A:11 showing on the display in my Hotpoint FDL570G dishwasher. What does this mean? How can I fix it?


I wish I had some good news for you... According to the Hotpoint error code list, your machine is experiencing the following: A11 - 1/2 load Solenoid Valve Triac or alternating Wash Motor action - check\015\012Solenoid Valve operation & al ... Dishwashers

LG dishwasher displaying EO error message - have checked all pipes, no blockages


LG Manufacturer Library »LG Customer Support: (800) 243-0000 \015\012\015\012E0 code is attributed to a short keypad with the Electronic Range Control (ERC).\015\012\015\012replace the erc ... Dishwashers

Hotpoint fdw80 dishwasher is not starting when a cycle is selected, just hear a soft growling sound, no error message displayed!!! Thankyou


Remove racks and filter cover to access the pump. It is probably stuck with debris.\015\012\015\012Use a wet vac to suction out the pump impekker cavity. ... Dishwashers

I have a PLD3460RDC1 dishwasher.The power got shut off and it now displays an ER message with all the other lights blinking.I have shut off the power to the unit many times, first getting a PF error and then it goes to the ER with all lights blinking. How can I reset this?


HI, there has been a power surge/pulse, that has been absorbed by the electronic control board. There may be serious damaged here, in this case. You can try to reset the main logic chips by unplugging, or shutting power down for five minutes. If the ... Frigidaire Dishwashers

My Kenwood dishwasher keeps displaying error message E4 but there is no mention of this in the user manual. Can you explain what this means


Hello,\015\012\015\012Some\015\012models of Frigidaire washers come with a digital readout display that\015\012informs the operator of the unit's function and any errors. Error codes\015\012indicate that a problem has occurred ... Kenwood KDW243A Builtin Dishwasher

LG LD-2120WHU dishwasher take in water like normal, wait a fewe seconds and then pump it out again showing the error message E1 on the display?


... Dishwashers

Vibrating noise when running the dishwasher. No error messages on the display. We looked to see if something was caught in the bottom, but don't see anything.


YOUR BELT IS GOING BAD. ... Dishwashers

LG dishwasher LDF6810ST doesn't dry dishes anymore. Added more rinse aid like manual suggested but no luck. Also dishes don't seem to be as clean, some food is left behind, which wasn't a problem before. I use Cascade detergent and Jet Dry. There are no error messages displayed. Help!


... LG 24 in. LD-12BW5 Free-standing Dishwasher

ASKO dishwasher my dishwasher came on spontaneously and keeps running first (drain, I believe) cycle. It stops when I unplug it (of course- no power) but sturts immediately when I plug it back. Error message is displayed


F2 fault water in the base remove dishwasher from under the bench and tip back water will run out,then it will restart.remove rear lower panel and run the dishwasher you may find a leak,also check that the inlet valve is shutting off and not filling ... Asko D1776 Stainless Steel Built-in Dishwasher

Hi, We have a miele G1220scu dishwasher. It is currently displaying error message F84. Can you please let us know how to fix it. Kind regards, richard.


... Miele Dishwashers

See below Hi, Disconnect the Power Supply for Few Minutes, say 10 minutes and then Turn it ON. Do you see any Error Message on the Display? Do you see any Other Light Blinking? Have you tried to Press Cancel / Any other Button on the Touch Pad? Is it Working? Do you hear any Beep? Let me know, if needed further assistance. Hope i helped you. Thanks for using ' Fixya ' and have a nice day!! Comments: Apr 02, 2010 - Thanks for your response!! One more detail, i wanted to ask - Is that Wash Li


What's going on here? ... Dishwashers

I have a LG intello dishwasher 2050SH Turned it on yesterday and did a rinse. This was the first use for 4 months in our second home. It was very cold. The rinse stopped some way through and an error message displayed (cannot remember). Tried to run again and now the dsiplay is locked. It turns on with usual sound, but none of the buttons work. They make a noise when pressed but nothing on the dsipay changes. I suspect that the outlet was frozen and that I should not have tried again - too im


Hi\015\012\015\012To\015\012unlock the lock in your LG Dishwasher, with the door open press the SPRAY &\015\012RINSE buttons simultaneously for 15 seconds. Hope this helps...please post back fo ... Dishwashers

My dishwasher stops annd displays E1 error message on panel


Hello there and welcome to fixyaThe E1 error code is a fault code for the pump meaning that the pump may be clogged or it may have failed all together so you are going to want to first unplug the machine or disconnct the power to it ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0457 seconds