Having problems with your Frigidaire PLD4375RFC Dishwasher ?

Frigidire pld4375rfc2 display says er - Frigidaire PLD4375RFC Dishwasher


Answers :

I rough guess is that there is moisture build up in the air vent causing the controller to fail. This could be due to not enough gap between the dishwasher console and the kitchen benchtop.
Not sure how long you have had the dishwasher, but a check might be handy.

Refer installation inststructions in particular about the use of the cabinet seal kit.
Repair Help & Product Troubleshooting for Frigidaire PLD4375RFC Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Frigidire pld4375rfc2 display says er - Frigidaire PLD4375RFC Dishwasher


I rough guess is that there is moisture build up in the air vent causing the controller to fail. This could be due to not enough gap between the dishwasher console and the kitchen benchtop.Not sure how long you have had the dishwasher, but a chec ... Frigidaire PLD4375RFC Dishwasher

My dishwasher display says Lo after a cycle - Frigidaire GLD2445RF Built-in Dishwasher


... Frigidaire GLD2445RF Built-in Dishwasher

My Frigidaire Dishwasher PLD4375RFC is showing 3 blinking lights at the same time when I flipped the power at the circuit breaker off-on: High Temp Wash, Air Dry on the touch pad and PF on the display. It would not respond to anything that I tried. All blinking lights are off and machine does nothing when I open and close the door. Flipped the circuit breaker off-on again to repeat the sequence. I replaced the controller board, as recommended by the appliance guy since he checked and said ele


... Frigidaire PLD4375RFC Dishwasher

I have a frigidaire dishwasher model number pldb998ac1. When the dish cycle ends... the digital display says


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

My dishwasher will not start. It is a frigidaire / electrolux FDB1050REQ. I have checked thepower....and reset the circuit breaker.......then pushed the start button.....the light comes on on the front of the washer like normal but no water starts filling. I have jiggled the anti water overfill device but still nothing. HELP!!! The front of the dishwasher says Frigidaire, however, the inside of the door where the model# is says Electrolux


... Frigidaire Dishwashers

My Bosch dishwasher has several problems: 1) Water doesn't completely drain out and dishwasher kind-of smells when I open it -- I do keep the filter very clean. 2) The dishwasher takes HOURS to go through one load, no matter what the time says on the display and no matter what type of cycle you choose -- quick, delicate or regular. 3) The red display often displays something that looks like "2h" at the beginning of the cycle. 4) The place where you put the detergent doesn't shut.


Hi Kathryn .I think you have a defective pressure switch. The pressure switch is located near to the drain pump, and the device is used to determine when water had been drained completely.Also check the floater switch located ... Dishwashers

My dishwasher will not start. If you unplug it and plug it back in it says 1H, no matter what button you press it then says 2H and if you press another button it will say 3H until it runs through to 9H then will display --. It will continue to do this until you leave it alone and walk away. Then after a few moments it will clear itself out and the 'Normal' light under cycles will continue to blink. The dishwasher is 3 maybe 4 years old. Please help, I have a 3 year old and an 18 month o


Hi,There could be Few Possibilities.Let's try to Reset. 1h, 2H -----9H usually shows delay X hours Display where X would be 1,2...9.Turn the Power OFF for few minutes, say 5 Minutes and then Turn it ON. ... Dishwashers

I have a Bosch SHU5316UC dishwasher. The last two times it ran, my wife says the display said "CL" (for clean) after running through the cycle, but she heard a "motor running" until she opened the dishwasher. Attempting to run the dishwasher tonight, it won't start - it displays a "P" (error code?) when you attempt to start it. Can you tell me what the error code P is? Thanks, Dave


P stands for program in computer algorthms. The device displays program whenver chages were made to the default settings. A powered on devices least has malfunction only requires reseting to attaon default features. Depending on the type of device, r ... Bosch SHU5316UC Dishwasher

Frigidaire Dishwasher Hi: We recently bought a GLD2445RFC model Frigidaire dishwasher, and after we did everything and hooked it up to test it, it just flashes pf in the display area. What does this mean?


PF is merely an indcator to you that you've experienced a "power failure" normal to appear every timr you lose power and/or reset breaker. pressing any one of the buttons will clear it. ... Dishwashers

My brand new Samsung dishwasher today is displaying a 6E error message which my manual says is a functional error. It says to try to turn off the dishwasher and try to start it again. I seem to be unable to do this. HELP!


... Dishwashers

Cycle time remaining isnt displayed on Frigidaire Professional dishwasher


From my research, this unit is not designed to show it while in use only if stopped during a cycle or if a problem persists within the unit to cause a pause or error code to display. ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will c ... Dishwashers

I have a Frigidaire 1500 series with fully electronic control dishwasher. When I try to start it all the lights come on the display but not water enters the dishwasher. I have tried various settings including delay start but still the same outcome. The over-fill protector in the bottom of the dishwasher moves freely. What else should I try?


... Frigidaire Dishwashers

I am getting an error on the display it says Er in Orange along with an S in the right hand bottom corner and a couple other text it keeps flashing and the dishwasher hums for a couple minutes and cuts off the items on the display continues to blink


If you haven't got the instruction manual (which should explain the error messages), then you may be able to get one by going to ... Frigidaire Dishwashers

I have a Frigidaire Gallery Series dishwasher (model. GLD3450RDB0) that always displays the "lock" icon under the no heat dry button. I am able to get rid of it by holding the button for 3 seconds, but I am still unable to select anything or get the dishwasher to start afterwards. As soon as I close the door, the unit locks again! What can I do?


Have you tried unplugging the dishwasher for a while then .. Trying it again.. If the problem still persists have a cleaning done to the control board and touch pad inside and if still the problem persists then i doubt whether the problem is that the ... Dishwashers

Own a Frigidaire Dishwasher Model Number FDB4315LFSO and now after about 2 years suddenly the display will not light and function anything. Without pulling the power panel off the whole line circuit seems to have power as they have my disposal unit tied into same electric line and that runs and so does everything else and no breaker is tripped. Is their a reset somewhere to check or any ideas what can casue the display panel not to function any commands at all. Nick


... Dishwashers

My Frigidaire PLD4460REC0 dishwasher status indicator is completely black. The window used to have a green display with the cycle timer. The dishwasher seems to be working fine and I can even change cycles but the status indicator is blank.


Hi\015\012\015\012First make sure that nothing is blocking the drain pump\015\012assembly located inside the lower front panel of the dishwasher. If the issue\015\012returns after its cleaned then try to reset the dishwasher control by pr ... Dishwashers

My dishwasher won't stop running. It has even run for a full day until I cut it off. Is this something I can fix myself? My dishwasher is a built-in Frigidaire. The manual says 2000 series, but I do not have any specifics. It is probably a 24 inch.


... Frigidaire Dishwashers

Suddenly, an error message appeared on the display of my Frigidaire gallery series dishwasher, model number GLD3450RDS0. On advice from Electrolux customer service, we cut off the power supply for one minute. When we turned the power back on, the display read PF (for power failure), but then it went completely black. Any advice?


... Frigidaire Dishwashers

The display panel displays random numbers and jumps around... When I start the dishwasher the front panel say: 180, then 67, then 39, then 69..68. 69. 66. 37. 180...etc... It seems to be running though... totally weird. The Control Board has NO error code. I replaced the Control Board. Didn't fix it.


... Electrolux Dishwashers

Frigidaire PLD4375RFC Dishwasher Dishwasher. Error code PF keeps flashing. I can open and close the door, it goes off. A litle later it starts flashing again. PF, means power failure


... Frigidaire PLD4375RFC Dishwasher

Frididaire dishwasher HO on display screen - Frigidaire Dishwashers


If it is coming on during the cycle it means the dishwasher is heating the water. If it is after the cycle or the cyle is stopped it means it did not reach the proper heat temperature. As long as it is running through the whole cycle it is ok. ... Frigidaire Dishwashers

I have a Frigidaire Model Number GLD4355RFS1 Serial Number TH80493988 Dishwasher. It quit working when the Rinsing Agent Low light came on. We filled the rinding Agen dispenser with hopes that it would come back on. The Rinsing Agent Low light went off but the unit never came back to life. When the room is totally dark, you can just barely see the lights in the LED display and other lights. It will not come back on. I tied turing the power off and the "PH" alert is displayed in t


... Frigidaire Dishwashers

Gaggenau GM915-710 When I turn on the dishwasher, the display says 13 and the washer runs. But it run until the displays shows 1 and it is stuck there. I hear the machine going but it never stops.


... Gaggenau GI936-760 Dishwasher

Frigidaire Gallery Series Dishwasher - unit stops near the final rinse cycle without draining - "ER" on front display, all led indicators on front display also lit (e.g. low rinse agent, etc.), and the "Hi Temp Wash" light is lit, regardless of cycle setting at beginning of cycle - rinse cycle seems to function normally


HI,check your drain hose first for kinks or food blockage also check the\015\012tail at the disposal or wherever you drain hose connects. Second there\015\012may be a blockage in the pump itself take it off and check. If all of\015\012thi ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2169 seconds