Having problems with your Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher ?

Dishwasher will not drain, replaced the pump and ran through the cycle and sounded like pump came on but water stayed in the entire time. What would be the next step?


Answers :

Check the bottom of the washer the drain may be plugged if not the pump\015\012may be malfunctioning.To check it disconnect the hose where it enters\015\012the drain pipe and put it in a bucket then cycle the machine water\015\012should start fillling the bucket. if it doesnt call a service tech.
Seem clogged after a garbage disposal is added to the sink area.\015\012Happily, this is not only a common problem but one which is usually\015\012resolved quickly. You'll simply have to check a piece called the\015\012knock-out plug. That should resolve the issue. Kevin


Repair Help & Product Troubleshooting for Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher will not drain, replaced the pump and ran through the cycle and sounded like pump came on but water stayed in the entire time. What would be the next step?


Check the bottom of the washer the drain may be plugged if not the pump\015\012may be malfunctioning.To check it disconnect the hose where it enters\015\012the drain pipe and put it in a bucket then cycle the machine water\015\012should start filllin ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

I have a Bosch Diswasher that is not draining. I have disconnected power for 35 minustes and used shop vac to excess water out of drain line. i also pulled all water thru the drain line from the tub itself. i assume that because i could pull the water, all baffles and lines are clear as i emptied the tub from drain line. you can hear the pump come on to drain water but no water is moving. What would be my next step. If it is to replace the pump, how do i easiest access the pump to remove and rep


Either the selector switch or pump is faulty. If there is not any clogs anyways. The system may need to be reset. Most resets are done by entering a series of numbers on the touch pad to enter diagnostic/test mode where the machine can be reset. This ... Dishwashers

We installed a Samsung DMT 300 and gave it a test run. All went well. The next time the lady used it it would not pump water into the machine. We went back and checked and there is water to the machine but it will not go into the machine. Any ideas? Thanks.


... Samsung Dishwashers

Good Afternoon We have a Kleenmaid DW8 dishwasher. At the beginning of the cycle, it will pump out the water, sit idle for a short time and then show the end light, without washing or any further action. A technician came to visit and had a brief look. A follow up call came from his company stating that the circuit board had a crack in it. It would require a new circuit board ($650), the dishwasher to be taken to the workshop and repaired ($150). Upon further investigation, the circuit board had


... Dishwashers

I have a du1145xtpq7 whirlpool dishwasher. Out of the blue it quit working completely. The sensing and washing lights light up, but when it goes to the next step of just washing nothing happens. The soap dispenser door opens and there is water in the bottom of the dishwasher. It wasn't making any irregular noises, unless I'm just used to them since it came with the house. Any advice you have would be appreciated. Thanks.


... Whirlpool Dishwashers

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

Have a LG model LD-14AW2 dishwasher which has done good service for many years However, it now sems not to have enough water pressure to operate all the rotary sprayers at the one time - thereby not cleaning properly Have purchased a manual and raken the whole machine apart looking for a partial blockage of the water ways - non found - all looks perfect - still no water pressure I would suspect the pump - however, would have thought a pump either gave full service or stopped - not parti


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Dishwashers

Kenmore Dishwasher model 665.1675592 doesn't seem to wash as well as it used to. Seems to have a low water level. Filler valve works, allows water in, but never seems to fill enough. No spray reaches top shelf, I think due to insufficient water level. It's like the timer doesn't stay on long enough for it to fill. Also cycle time seems WAY up, but if the timer is slow, how does it time out filling so fast? Looks like it would be slow all the time. Suggestions?


... Kenmore Dishwashers

Good mroning after starting any program first the pump will run followed by water intake. After a while the machine stops and the light intake/drain starts blinking. Most of the time water will stay in the machine. After pressing the on/off bottom first switching the machine on again and starting a new program the machine pump start running emptying the water but than stops after a short water intake again. I opened the water stop but it seems to be ok. The filter inside the machine is cle


Good morning don't get shocked because ullu ki to abhi subah hi hui he ... Miele 24 in. G892SCU Plus Built-in Dishwasher

I have an Asko 1585 dishwasher. It drops the inlet valve on step (step 12), and the recirculation pump (next step) tries to pump with no water. Later at about step 47, the inlet valve begins to work again and the dishwasher finishes the cycle without a problem. I have had the board checked, and all of the power supply and transfer circuits are good. That leaves the processor. Is there any combination of buttons to press which can completely reset the controller board?


... Asko 24 in. 1585 Built-in Dishwasher

Some guys at the church was using this haracher 4000 psi, I was call and was told the machine stop working and would not crank up.I use a next machine to finish the charity jobs on saturday. Sunday the machine starts up but when I connect the garden hose and turn on the water it did not comes out, where the VALVE HOSE THAT GOES TO THE WAND ABOVE THE UPLOADER, I open every bolt and water comes out except the wand valve, pump was plush out and sprayed out, so we know that water enter the pump


Where the hoses attach to in the pump is a valve along with another valve inside of it. Remove both valves and clean and relube with Vaseline or equivalent. The inner valve will be the toughest one to remove and that its why it does not work if stuc ... Karcher Pressure Washers

My GE Nautilus dishwasher keeps PUMPING water "out" of the machine during the entire wash cycle. I have removed all covers in the bottom of the unit to see if anything is stock. Used vinegar and CLR to remove mineral deposits-- yet nothing solves the water being pumped out the drain hose.. what's next, please.. a solution !?!


If this convert-able dishwasher is permanently installed, you will have to take off the lower access panel to get to the pump area. If it is still in a portable configuration, it may be easier to lay the dishwa ... GE Nautilus 24" Built-in Dishwasher

Recently our GU1100XTLQ1 started having a problem. It barely cleans the bottom rack, and barely gets top rack wet. The soap stays stuck in the dispenser. I can't see inside as it runs, but my guess is that not enough water is being shot out of the various spinning arms. From looking at diagrams it would appear that this dishwasher uses a pump to circulate water from the bottom of the cavity through the spinning arms. Is my problem a dying pump?


... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

Magic Chef DU55CA-01 unit runs but when pump kicks on for discharge cyle water leaks on the floor from the what appears to be the solenoid part. The leaking stops as soon as the pump turns off. What part needs to be replaced? The unit was in storage for some time would this just be an issue with it sitting for some time? What is the best way to determine the real cause of the leak?


Leaking from drain valve shaft seal. If you just replace the seal it may still leak. Replacing the pump is a lot of work and not really worth it to cure a small leak. ... Magic Chef 24 in. DU6550 Built-in Dishwasher

I have the E3 error on my Smeg DWI614 dishwasher which would indicate a heater error, however it is heating the water in the bottom of the machine but it seems to time out. The main issue seems to be that the recirc. pump is not running during the heating phase. I have taken the pump out, checked the connections etc. twice now and everything seems fine (the motor runs when tested). When I have done this (both times) the dishwasher has started again and run for 20+ cycles fine, then the issue com


... Smeg DWI614 Built-in Dishwasher

My Bosh Model# SHE4AM02UC/01 Is not cycling. Started with the soap dispenser not opening, progressed to the drain pump not staying on. When you turn it on, the pump runs for 2 seconds. water solenoid opens for another two seconds, and then the "clean" light comes on. If I go to quick wash, or to pot scrubber it might do a regular cycle. I did pull the pump to remove a piece of glass before this all started, but can't imagine that would be the cause.


... Bosch SHE4AM02UC 24 in. Built-in Dishwasher

Obtained this haier hdp18pa portable dishwasher, thought I would give it a try. The unit will not fill with water, turn the power on you can hear the motor or the pump running but no water comes in. THe 4 display lights flash and beep a series of times and then stop only to repeat the sound off in a every few second sequence. I have tried the remedies offered online, tilting the unit does not seem to work for me on this one. I changed out the water inlet valve but nothing changed and I got the s


HiYou need to clean the filter that is in the tube that gets water in the dishwasherin case you can not find it pls ask me to send you a diagram ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

Miele Optima G 2430 - The dishwasher will pump water in for 5 seconds with the Intake/Drain light flashing 5 times. Then the light stays on for 5 seconds and it does nothing. This process is repeated for about 10 minutes untill the washer is filled to the just below the door with water. Then the washer starts running for about 1 1/2 minutes and drains the water. Then it all starts over. If I let it do this for a hour - The display reads F12 with the Intake/Drain light flashing.


Hi\015\012\015\012The first thing that should be checked is if its draining\015\012properly as it could be that the drain hose is clogged and needs to be cleaned.\015\012The drain pump also should not be clogged. ... Miele 23 in. Novotronic G841 Built-In Dishwasher

When the dish washer is done washing the bottom is still full of water. When you start the next load it pumps the old water out and washes the load. Never did it stay full of water in the past.


Since\015\012 the drain pump will pump the water out using the "cancel/drain" \015\012button, if it did not work then your problem is likely to be in the drain hose system or the \015\012garbage disposal downstrea ... GE GSD5610D Dishwasher

DISHWASHER-GE GL613716A will not drain. re/re drain and removed restriction,food ect. it will not drain still. performed self diagnosis on front control panel as per trouble shooting information supplied with dishwasher when i bought it, all tests passed except when commanded on, the pump did not drain water from the dishwasher, i do not know if the pump came on as all test functions are perfomed at the same time for some reason, which made a bit of noise making it hard to even hear the pump. th


Hi,\015\012Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...Dishwasher Problems - Water will not drain ... Dishwashers

I have a Bosch dishwasher and it is not draining the water out. I have pulled from under the counter to make sure there were no kinks in the hose. I can hear the motor turn on to pump the water out but no water moving. any suggestions on what to do next would be great


Have you checked the waste food sump below the screen for blockage from washed off food ... Bosch Dishwashers

I have a Kitchen Aid KUDS03CTSS3 dishwasher. Dirty water is staying at the bottom and nothing comes out the drain hose during the entire cycle. The drain hose is looped above the kitchen P-trap, although for a time it wasn't. I use a wet vac to get the water out but there is still water below the fine filter. I thought if I could get the fine filter off, I could clean out the bottom as I think that it's full of crud down there that may be blocking things. I can't figure out how to get the l


Hi,Thanks for the follow up. I am glad it worked out for you. If I can Help in the future let me know. http://www.fixya.com/support/c64627-kitchen_aid ... KitchenAid 24 in. KUDP02FR Built-in Dishwasher

I have a Comet BXD 2525 G pressure washer pump which is giving me some problem. (Maybe) I hook the water up to pump and the pressure hose up to the pump, turn on the water and the water sprays out of the water connection at the pump. I check the hose to see if it was clog ok and the next was a the water connection ok. It's like the water is not going int the pump. When i start the pressure up the water come out of gun but no pump running like it should. The next thing i was going to look at i


The water inlet needs a gasket like all hose connections. If its gone the pump may be starving for water. ... Comet Pressure Washers

Noticed dishes on top shelf not entirely clean. Ran machine empty and opened many times during wash. Noticed that Lower Spray Arm works as expected, but Middle Spray Arm turns only 1/8 or less, then Lower Arm spins again. Schematic with Use and Care manual just says pump motor switches from one to the other in certain cycles, but I don't see this happening. Looked for obstructions to water flow and pressure seems normal. Is control for this function part of the pump, or in the control panel?


Something could be in that checkball, see page 5 ... Frigidaire 24 in. GLDB653A Built-in Dishwasher

Often had to press 'Start' up to 5 times to get it going. All lights light up but then go out. Occasionally the pump would run for a minute or so then whole shooting match would close down. Recently we were lucky and it filled with water but sadly disappointed when it closed down again. 8 people in the house so had to do the dishes in the sink (again!!). Plenty of helpers and a glass or two of wine so things weren't that bad. Not good for Dishlex though especially when others say theirs are


Problem not solved yet.\015\012Cleaned the filters well, hoses clear and water delivery happens.\015\012Both pumps work happily so are not seized/locked up or have anything jambed in them (pulled them both out and checked for foreign obje ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1866 seconds