Having problems with your Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher ?

Frigidaire 1500 series dishwasher will not wash or rinse

\015 The unit fills and then nothing happens until it drains. Then it fills again before the rinse cycle should come on but again does nothing. The water level covers the filter. the heating element seems to work. the detergent dispenser never opens.\015

Answers :

Hi there,

After the unit fills for the second wash, open the door and check the\015\012level of water in the tub. It will not leak out and the unit will\015\012stop when the door is unlatched, then reply with the water level.

When \015\012 a dishwasher detergent dispenser starts acting up, there is usually \015\012 a detergent clogging problem present. Rinse out the dispenser cup \015\012 and try switching to a liquid gel detergent. There \015\012 also could be a problem with the spring on the dispenser having \015\012 gone bad. The spring can be replaced by first removing the front \015\012 panel of the dishwasher, then loosening the bolts that hold the \015\012 dispenser cup to the dishwasher door.
If \015\012 the dispenser cup is not spring-loaded, then chances are it uses \015\012 either a bi-metal switch or a wax motor to disengage the door. These \015\012 can be swapped out.
A \015\012 defective timer switch can also be at fault.

hope this helps

Repair Help & Product Troubleshooting for Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Frigidaire Gallery Series Dishwasher - unit stops near the final rinse cycle without draining - "ER" on front display, all led indicators on front display also lit (e.g. low rinse agent, etc.), and the "Hi Temp Wash" light is lit, regardless of cycle setting at beginning of cycle - rinse cycle seems to function normally


HI,check your drain hose first for kinks or food blockage also check the\015\012tail at the disposal or wherever you drain hose connects. Second there\015\012may be a blockage in the pump itself take it off and check. If all of\015\012thi ... Dishwashers

Frigidaire 1500 series dishwasher will not wash or rinse


Hi there,After the unit fills for the second wash, open the door and check the\015\012level of water in the tub. It will not leak out and the unit will\015\012stop when the door is unlatched, then reply with the water level. ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

I have a frigidaire dishwasher 950 series. Filled washer hit start button no light but water is running. Wash cycle only no rinsing. And it will not shut off.


... Frigidaire Dishwashers

Frigidaire dishwasher PLD2855RFC rinse aid leaks around cap. How to fix? New cap? Is this a recurring problem? I have found rinse aid on door below cap (residue) plus have found rinse aid itself on dish below dispenser. I have to refill the rinse aid reservoir about every 7 or 8 wash loads. Also, the dishwasher is very noisy when running (should be quieter). Not very happy with this model ...


... Frigidaire PLD2855RFC Dishwasher

Bosch SHU43 My Bosch SHU43C dishwasher stopped washing, turns out the impella came free from the motor, I repairded impella and put it back together and now the dishwasher washes great however now it is stuck in a wash rinse drain cycle. Display counts down but the unit never stops running when it reaches 0. Also, the water level is higher than normal and I there is a kind of thumping sound repeatedly every 15 seconds " use to make that sound only once at the start of a cycle before the impella


Sounds like the control module is out -- cost about $100 (I am on my third). I got a "lifetime" warranty when buying my second one. If you are handy, you can replace it yourself. You can call Bosch to confirm this (I did). It mounts inside the door. ... Bosch 24 in. SHU53 Built-in Dishwasher

Frigidaire dishwasher won't end cycle - will run on and on for hours. Sometimes it cycles through, usually it just endlessly washes and rinses. I have to CANCEL the cycle, which causes the dishwasher to empty and run a few RINSE ONLY cycles (which are consistent, cycle time wise) to rinse the soap off of the dishes. Also, the door for the soap seems to stick - how long into the cycle before the soap door should open? Also, does opening the washer during it's cycle (to add more dishes) change or


I would say the resettable thermostat has failed. There is a thermostat which senses the water temperature, and when it fails, it causes the dishwasher to run constant. Replace the thermostat underneath the dishwasher and that should cure problem. P ... Frigidaire 24 in. FDBB540 Built-in Dishwasher

Dishwasher Repair I have a Frigidaire dishwasher that came with the house. The house and washer are probably about seven years old. It woked fine for the first few months but now, when I turn it on to wash it fills with water but then it will not go into wash cycle (i.e. there is no water sent into the dish compartment). It will go through every cycle by filling and emptying through wash and rinse but no water goes into the dish compartment. Is there a pump that is perhaps not working? How is th


Ebers, you have a seperate wash and drain motor on this model. When you remove the bottom panel the drain pump will be on the right and the circulation (wash) pump will be in the rear. You are going to have to verify that you have power getting to t ... Frigidaire 24 in. FDB421RF Built-in Dishwasher

I have a Maytag Quiet Series 300 dishwasher model number MDBH955AWW. When I press the wash cycle button it starts and then automatically jumps to the rinse cycle. After going thru the rinse cycle for a couple of minutes, it shuts off. After that,I can push the wash cycle agin and it works. Any idea what could be wrong?


HI. This will be a basic logic chip fault. It could possibly be solved by simply preforming a hard reset. You can do this by shutting down the power to the unit for five minutes. This shutdown will force the logic sector of your electronic control bo ... Maytag 24 in. MDB9750AW Dishwasher

There is water leaking between the left and right seals on our Frigidaire dishwasher FBD700BFC2. The dishwasher is level and was installed by the builder two years ago. The seals are intact, and water only leaks during the wash and rinse cycles. What else should be checked or done to prevent the water from coming out of the dishwasher.


Sorry to read about your problem, I hope this helps you out.its time for new seals...I tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Frigidaire FDB700BFC Built-in Dishwasher

I have a Frigidaire Aqua Surge with Speed Clean dishwasher. The model # is FDB4315LFCO The serial # is TH64297242. There always is a smell in the dishwasher. Even when I have just washed the dishes, when I open it it smells. Also when there are just a few dishes in and I close the door and reopen it, it smells. I rinse everything very well before I put the dishes in. I have tried cleaning it with a dishwasher cleaner and that didn't help. HELP!!!!!


HELP s on it way . it is or may be a install problem . take a look at the drain and how it connected to the disposal . If where it connects at that point the hose is going down hill then when the disposal is se ... Frigidaire Dishwashers

I have a GE Profile Eterna series triton dishwasher. When it gets t rinse cycle, lights go out and it keeps rinsing. Buttons stop working and it won't stop or reset. If I unlatch door and wait for hours lights may come back and allow a reset. Run through 3 rinses only -fine. wash cycle does it again.


... GE Dishwashers

I have a Frigidaire Series PLD2855RFC3 dishwasher. Near the end of the cycle the dishwasher stops and begins flashing "PF" on the display and the lights for "Hi Temp. Wash" and "No Heat Dry" also flash. I know "PF" = Power Failure, but the power never goes out... so what is causing this error and disruption in the cycle?


... Dishwashers

My Maytag Quiet Series 200 Dishwasher Model MDB6600AWW washes the dishes but does not go into it's rinse cycle and does not stop. I have to turn switch off at the wall to get dishwasher to stop. The water is hot and the dishes appear clean but it doesn't turn off.


... Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I have a Frigidaire Professional series less than five years old. It won't run and flashes the wash, clean, and sanitize lights simultaniously. Any thoughts on what the problem is and whether it is worth fixing? This is the second Frigidaire I have had in ten years. The model number is PLD2851RDC3. Any help would be greatly appreciated before I go out and get my third dishwasher in ten years!


Hi.The two lights are not an error code, but they are telling that the machine is in failure mode.The error code is retrieved performing a water/service test.The water/service test is a special function initiated ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

Hello, my Frigidaire Professional Series dishwasher (AquaSurge with SpeedClean) gives me error messages; it does not allow me to use any setting other than normal wash; it stops mid-cycle; it needs to be reset - either on the appliance itself or by tripping the breaker. I am never sure that the dishwasher will complete a cycle. Thank you for your assistance.


... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

2003 Frigidaire Electrolux Professional Series dishwasher, Model #PLDB998CC0 Apparently not rinsing properly: leaves white film on everything and it has to be manually scrubbed off as opposed to just rinsing under faucet. Is there a filter that should be changed out? I do not have the original owners' manual unless it is still attached to the back of the unit under the cabinet.


... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

The Frigidaire Professional Series Dishwasher is leaking dishwasher detergent ( during the wash ) all over my tile floor and staining my grout. It seems like the door will not shut all the way. If I push on the door all little, you can really tell a difference in the noise level. Is there a way to adjust the closure to close the door more?


Hi linsley.\015\012\015\012I'm Harvey the Master Plumber.\015\012\015\012Your question is: Is there a way to adjust the closure to close the door more?\015\012\015\012First lets back up a little . You say it's le ... Frigidaire Dishwashers

Have Whirlpool dishwasher Gold Series, Model GU9805CGB1 which stops part way through wash cycle with the led indicator blinks on the normal cycle.....if we ope nthe door and shut ...it continues until part way through rinse cycle...stops again....led indicator blinks again.....we open the door & shut and it continues....but then continues to run through the normal wash cycle continuously.....until we open the door again.....what's wrong???


Sounds like the door is losing contact with the door switch, first thing i would check is the door strike.Metal strike plate located on the tub itself that the door latch catches as it closes. its a spring metal striker, i would try bending it down ... Dishwashers

Does not drain after washing? - Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher


Hi,\012Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Noisey maytag We have a maytag quiet series 300 with the 3 racks. Just recently we have been hearing alot of noise from our dishwasher while it is in the washing and rinsing mode. We have checked the arms to make sure they are moving but doesn't seem to be a problem. Thought maybe there is a liquid that we could pour into the washer to run through it's cycle? Of course we know nothing about the inter works of a dishwasher.


Hi, i had the same problem twice and both time there was some plastic stuff in the shredder. Remove the screw in the middle and remove the cap and you will probably find some pieces near the blades. ... Maytag 24 in. MDB5651A Built-in Dishwasher

At 2 minutes left in the wash cycle, the quick rinse light starts blinking and the timer goes to 0. My dishwasher is a Whirlpool Quiet Partner IV gu1500xtkbo dishwasher. I'm assuming the blinking light is an error code. What does it mean?


... Whirlpool Dishwashers

I have a new FDB520RHS2A Frigidaire dishwasher which remains in the wash cycle after I've started it. It sounds as if it is changing cycles but the wash light stays lit and never switches to rinse. The machine continues to run for hours if I don't stop it. We've checked the drain to the garbage disposal and it is clear. the water temp seems to be hot enough but how do I check that? Any ideas on what we should check before we bring it back to the store? Your help is much appreciated. Thanks!


... Dishwashers

Miele dishwasher - insignia series - stainless steel model - no led just two buttons ... Power and select cycle . Green light usually move from rinse to wash to end.... It get stuck on rinse and just


Call Miele Technical Support at 800.999.1360. They can help you resolve your problem. ... Dishwashers

Grinding during wash cycle - Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher


Possible that there is fault in the spraying unit or arm. It can also be due to faulty PUMP or a dirty filter which can CHOKE the pump.remove and clean the pump and filtercheck this link for tips : ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1540 seconds