Having problems with your Gaggenau GI936-760 Dishwasher ?

Gaggenau GM 915-710 UC6 dishwasher will not fill and wash. Close the door, turn lever. Empties water from sump. (drain hose was not clamped above disposal outlet nipple, fixed that) Machine empties sump, but will not stop after sump is dry. Will not initiate fill and wash. Manually stop machine. Can't get control board to do the diagnostic to get an F #. Pressing button 1 and 3 at the same time. A couple of the plastic tabs on the circuit boards plastic support housing that link the


Answers :

Repair Help & Product Troubleshooting for Gaggenau GI936-760 Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Gaggenau GM 915-710 UC6 dishwasher will not fill and wash. Close the door, turn lever. Empties water from sump. (drain hose was not clamped above disposal outlet nipple, fixed that) Machine empties sump, but will not stop after sump is dry. Will not initiate fill and wash. Manually stop machine. Can't get control board to do the diagnostic to get an F #. Pressing button 1 and 3 at the same time. A couple of the plastic tabs on the circuit boards plastic support housing that link the


... Gaggenau GI936-760 Dishwasher

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

My Kitchenaid dishwasher (model KUDS02SRSS0) keeps burning out my dispenser. First I replaced the dispenser, then I replaced the control board and dispenser, it worked for two weeks and now I have a melted solenoid again in my dispenser. I've measured voltage to the solenoid and it is getting 110V through the entire diagnostic cycle. This is wrong. It should only get power at some point during the cycle to open the dispenser. It appears the control board has failed again and in the same wa


HI. The relay that controls the voltage and timed release command, via logic chip, is indeed damaged(stuck on). This is a common theme with this particular design. The original control board was recently replaced with a substitution model ... KitchenAid 24 in. KUDP01DLBS Free-standing Dishwasher

MAYTAG MDB7600AWQ DIAGNOSTIC CHECK USING CONTROL BOARD AUTO AND MANUAL, ARE GIVING ME A HIGH CURRENT WASH MOTOR DIAGNOSIS.(NORMAL WASH FLASHING) THE BOARD ITSELF CHECKS OUT OK. ALL FUNCTIONS WORK AS THEY SHOULD.WASHER FILLS THEN ATTEMPTS TO RUN FOR (ABOUT 3 SECONDS) IT WILL DO THIS 3 TIMES THEN BOARD GOES BLANK. ALSO, THE WASHER WILL FILL WITH THE DOOR OPEN??? BUT WON'T ATTEMPT TO WASH. REPLACE WASH MOTOR?? THANKS lYNN


I would agree.. Here is a site for you to copy and paste in your address bar that I think will be helpful:http://home.howstuffworks.com/how-to-repair-a-washing-machine.htm/printable ... Maytag Dishwashers

Kenmore Elite Dishwasher- The touchpad (control panel) keeps going ot and stops functioning. The control board is fine but the start button on the touchpad stops working. If I press it multiple times over and over it will finally engage and kick on. This is my second control panel, can the switch membranes be cleaned somehow?


Jodahabo,\015\012\015\012can you post the rest sequence? i would love to try this!\015\012\015\012thanks,\015\012\015\012the_strum_one ... Dishwashers

My Asko 1473 Superior dishwasher has just stopped filling. I've gone through the on-board diagnostics and find that the fill solenoid operation does not work. All other diagnostic tests are OK. I have no service manual but would like to find and replace the solenoid if that is all that's wrong. Can you help with advice or manual? cheers, Hal


Asko ... Asko 24 in. D3250 Built-in Dishwasher

It starts running then stops - starts pumping in water then stops, etc. burning plastic smell near top... doesn't leak, gets power, but begins to fill, then stops - might start to drain (pump), but then that stops too...


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I have a Maytag MDBH945AWB and it stopped working. When you press Start, the lights are very dim and does not start the cycle. If you select the 2/4/6 hour delay, this light is bright but when you press Start, the cycle does not work. Is the control board bad or the buttons


... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

Intake drain flashing - but this time because water is not filling. Checked voltage at controller board - inlet solenoids are getting 120V intermittently. I found online that this is the behavior for fault code f12. But my machine does not give fault codes directly - is there a way to get it to "blink" them?


... Miele 24 in. Incognito G843Vi Built-in Dishwasher

I purchased my Kenmore Elite dishwasher, model # 8542514, in 2003 & replaced the control board in 2006. Recently, I accidently opened the dishwasher during a wash cycle, but it continued working once I closed it. It seemed to work fine for a few more weeks. Now, however, I get nothing--no lights....just doesn't start up. I tried pressing all the code solutions listed on this site, but no luck so far. It seems to me that the control board/panel should last more than 3-4 years.


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a Kitchenaid Dishwasher M/N KUDS25SHWHO. Had to replace the control board because the unit would not start. Installed the new board and the unit now operates, but not correctly. Once in awhile on the Normal cycle, it will get a third of the way through the cycle and just stop. Used to be, you could hit any of the Wash Selection buttons and than any of the Options butons and then hit the Start button to begin the cycle. Now, as soon as you hit one of the Wash Selection buttons, the un


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

Hi, I have a zanussi DE6744S. I can select any program and water fills as normal. The problem is that the cycle runs and runs and dosn't stop unless I turn the machine off. When I restart the machine it just carries on until I press the current program button in for a about 10 seconds and the program stops. On the odd occasion it ends normally on the economy cycle (30 mins) but its pot luck. It does wash as normal but dosn't seem to get past constant washing (no drying) . Hope you can help, S


... Zanussi 24 in. DE6544 Built-in Dishwasher

Yes I have a Maytag Quiet 300 Dishwasher, Model No. MDB6601AWB. I can't get the control board to work. Some features I press and I get the green light but it won't start. What do I do?


Replace the control panel, not the control board, the control panel ... Dishwashers

How can I shut off the water supply to the dishwasher? It fills slowly with water from the top (while not running), and then water spills out over the kitchen floor. By pressing the 'Drain' button, the water will drain out, but I have to get to it before it floods. It takes about 4 hours for it to get to the overflow stage. It is a Jennair model, about 9 years old. We have a lot of limescale, it is probably time to replace it, but for the moment my main concern is to stop the leak. Thank you for


Most water supply lines are attached to the hot water supply under the kitchen sink. If not it may be accessible from the basement somewhere under where the dishwasher is located. Regarding the issue with the dishwasher, the inlet water v ... Sears 24 in. 14181 Built-in Dishwasher

My Kenmore ULTRA WASH dishwasher model #1603* does not respond to any command. When I select a desired washing I only get a blinking light on my selection and nothing else. If I select ''Cancel/Drain'' it blinks as well. I receive no response at all if I select ''Start/Resume''. To stop the blinking I must turn off the circuit breaker. When I restore the power, the control board is not lit, however, selecting any of the wash cycles and the blinking starts once again. The manual refers to a blink


Replace timer/program module\015\012Vitally ... Kenmore Dishwashers

My Maytag MDB5600AWB quiet series 100 dishwasher starts, fills with water and then makes three "clicking sounds", after the third click the machine stops and turns itself off. I can get the water to drain by restarting the machine and pressing start/cancel. Anyone have any ideas?


... Maytag Dishwashers

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

Dishwasher overfilling Our dishwasher continues to fill and drain and won't stop. Our repair tech said the control board is bad. This is a minimum $400 repair. What are our options? If any.


I have been working on ASKO for several years and have never seen one fill and drain at the same time. Usually if it drains and cannot be stopped, it is because there is water in the lower tray that needs to be removed or left to evaporate, and then ... Asko D1776 Built-in Dishwasher

The control board seems to be locked in the drain cycle. I have tried powering it down for 5 minutes by unplugging it. I have tried to run a diagnostic cycle, but the only thing I get is error codes C1 and P0.


Hello, Welcome to FixYa. ... Bosch 24 in. SHX57C02UC / SHX57C06UC Dishwasher

I have a model 665.13593k600 that was running and during mid cycle it just stopped. I have checked and the d/w is getting power to the unit. Does this mean its the control board?


... Dishwashers

The machine does not seem to rinse properly. We have checked the water fill level, water temperature, spray arms are not clogged, have determined it is not a hard water problem and have tried Glass Magic and CLR to verify the lattter. What else can we check to stop getting a film on everything in the machine? Plastics come out terrible, glasses and dishes foggy and sometimes still greasy. The model # is GU2700XTSY0 from the Whirlpool line of Quiet Partner 4. Any suggestions would help. Thanks!


Too much detergent; not rinsing well; hard water... There is an acid wash to revamp glasses/ you'd need to google it... ... Whirlpool GU2700XTSS / GU2700XTSY Built-in Dishwasher

I have a Smeg DWD1SSE dishwasher, that has decided to start and stop on it's own during the wash cycle. We have to restart it at least three times during the 30 min short wash, and it very rarely gets to finish a whole cycle. I have stripped it down to make sure that there is no moisture on the main PCB behind the buttons, which there isn't. I think it looks as though the control board is faulty. If anyone can help or back my thoughts up, I would be very great full. Thanks.


... Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

I have a Bosch SHU53513UC/U12 dishwasher. My initial problem is that the washer smells bad after a cycle and I've noticed some water sitting in the bottom of the unit. After running a diagnostic test, it results in a "2" heating fault. I followed your advice and used a current coil to and attached it to the GYBK-a1-3 hot wire on the control board. After running the test again, it only gets as high as 1.15A and manual says it should reach 11A. What should I do next?


Hello,Welcome to FixYa. ... Dishwashers

DW244UW - husband is trying to remove the control circuit board (from plastic) to see if solder joint needs fixing (as per yesterdays instruction) - is there a trick as he can't seem to get it out to look at it?


Hello again Kathy,\015\012\015\012I just saw your post and I see you're attempting to follow upon yesterdays information we discussed. Can you post an email address here ? If so I can provide you folks with a complete service manual to help move forw ... Thermador Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1667 seconds