Having problems with your GE 24 In. Black Built-In Dishwasher - GLD5708VBB ?

GE gld5708vbb flashing lights locked controls

\015 Our dishwasher died mid-cycle. The repairman came out today and replaced the control board, but said our neutral was bad. My husband fixed the neutral, started the dishwasher, and it filled and ran for about 3 minutes and then quit & started beeping. He reset the power at the circuit breaker. It started beeping and the 4 & 8 hour green lights were flashing, along with the orange light on the front. It wouldn't reset. Shut off the power again. After that reboot it started beeping again, then the clean light kept flashing. The beeping has stopped, but the controls are still locked up. Thanks for your assistance!\015

Answers :

It is possible that since the neutral was bad it could have made a surge on the power and caused the processor controller to fail. It is also important that this must be confirmed to be corrected by checking with a larger load like a heater being switched on and not causing any voltage drop. If so the line is clear. Also make sure that the ground - Earth- is also intact.
The program has reset because of an error and it must be confirmed to be within or outside the washer. So remove plug and test this terminal with a large load test to confirm that the outlet is OK.
If so check the panel connections or is best to refer back to the dealer as the replaced panel will have a warranty.
Please take second opinion before the board is removed.
Repair Help & Product Troubleshooting for GE 24 In. Black Built-In Dishwasher - GLD5708VBB

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

GE gld5708vbb flashing lights locked controls


It is possible that since the neutral was bad it could have made a surge on the power and caused the processor controller to fail. It is also important that this must be confirmed to be corrected by checking with a larger load like a heater being swi ... GE 24 In. Black Built-In Dishwasher - GLD5708VBB

I have a Whirlpool dishwasher model #DU920PFGQ4. The controls locked light is flashing, and when I press the air dry key for 5 seconds it won't unlock, however the cancel/drain light starts flashing. When I press the cancel key the controls lock light will stop flashing, but will resume as soon as I release the cancel key. I have tried disconnecting power for 24 hours, but as soon as I plug it back up it does the same thing. Nothing else on the control panel will work.


... Whirlpool Dishwashers

I have a Kitchen aide dishwasher Model KUDI01ILWH6 that will not turn on..there is a control lock light on and I have tried pushing the cancel button but all that happens is the control lock light flashes 3 times and the dishwasher still wont turn on....Please , how to I disengage the control lock


... KitchenAid Dishwashers

Kenmore Ultra Wash Dishwasher Model 665.15779 LOCK ON light blinking on control panel, unable to use washer. If buttons were locked, LOCK ON light should be lit continually not flashing. If you press and hold NO HEAT DRY button to disengage lock, nothing happens. If you press the CANCEL button it begins to blink in unison with the LOCK ON light. How can I stop the light from blinking to allow button function again?


... Kenmore Dishwashers

The control lock sanitized clean light (green) keeps flashing on and off. No other bottons will work while the light is flashing. It flashing wether the door is closed or open.


... KitchenAid Dishwashers

I have a Frigidaire Gallery dishwasher model number FDB989GFC2. All of the indicator lights on the right side are flashing (Controls lock, add-a-dish, washing, etc.). when buttons are pushed I get no response. Have tried turning off at circuit breaker for 1 hour, when powered back all lights still flashing and still no response from pushing buttons. Any ideas?


You need to rpelace the electronic control board ... Frigidaire FDB989GF Dishwasher

I have a Whirlpool Quiet Partner 2 dishwasher from Lowe's model DV 1055XTVS. The "clean" light flashes three times in a row over and over and the "lock" light is one. None of the controls will work. I unplugged it and that did not clear the problem. How do I unlock/reset the controls?


I have a whirlpool quiet partner 2, its brand new. It leaves a filmy residue on my plastic ware. I use the finish detergent as well as the rinse and no luck. Whats the problem.???????? ... Dishwashers

Kenmore ultra wash 6651393 control lock light flashing


I would try turning the breaker off for 5 minutes to see if it will reset. ... Kenmore 15899 Built-in Dishwasher

Kenmore ultra wash dishwasher control lock light flashing


Just press the 'Air Dry' button for 5-6 seconds....I have an ancient Kenmore Dishwasher (ULTRA) ... Kenmore 15899 Built-in Dishwasher

Have whirlpool gold dishwasher made in Mexico, the control lock light stays on, when i push it and hold it just blinks three times and then stays on steady and then does the same over and over, before it did this I noticed the lights for different cycles flashing randomly, and even pushing cancel button once in a while would start the machine up....I have tried to unplug the machine and then plug back in, but nothing is helping....any ideas??


... Whirlpool Dishwashers

My kenmore elite ultra wash dishwasher flashing start button 1 hr light on. And control lock flashes but does not run just beeps


... Kenmore 24 in. 16059 Built-in Dishwasher

Our Kitchenaid dishwasher model # KUDP021R will not start. We close door, select wash and press start. The control lock light at the top which is lit flashes a few times and then stays lit. Dishwasher remains silent. An aside which may be helpful is that the door has always seemed to be not quite straight...as though it had to warp a tiny bit to close and lock.


The problem you have already identified could be the door switch is not closing when you shut the door. Please confirm your dishwasher is KUDP02I (i and not 1).\015\012\015\012One way to check is find out the door switch on the door panel ... KitchenAid Dishwashers

Leak from a De Dietrich Integrated Dishwasher has caused 3 red lights on the left of the Control Panel to flash and also a Blue Light on the right hand side of the Control Panel to flash. On resetting the Appliance Controls, the machine starts pumping out and then closes down, with the Control Panel lights flashing again. Help


Pull the built in unit out and tilt towards the rear right leg and the water will drain on to the floor. The Dishwasher then restarts but the anti flood sensor will reactivate after 2-3 more washes. Do not know final fix yet. ... De Dietrich Dishwashers

Model #PLD4555RFC0 The control panel lights on the front are all flashing and start cancel button will not change anything. flashing Er with wash, dry, clean, and and S showing. Top controls have China/Crystal light flashing and Low rinse agent light flashing. Nothing seems to work


... Frigidaire Dishwashers

Kenmore dishwasher Lock On light flashing


Holding the button for four seconds will not do it, you have to hold it until the light stops blinking and\015\012will go back to normal, normall takes more than four seconds to unlock the unit, this is something\015\012the sears repair t ... Dishwashers

I have a whirlpool gold quiet wash p.us series 925 dishwasher and the controls locked light is flashing keeping it from operating


... Whirlpool Dishwashers

KUDS01FLSS KitchenAir dishwasher does not start; Control Lock Sanitized Clean light flashes on top panel outside machine


Hey Dianne Hunter, Check this link out for more info on the issue! It's a common error and it seems this will reso ... Dishwashers

Blue control lock light flashes on kitchenaid dishwasher


... KitchenAid 24 in. KUDP02CR Built-in Dishwasher

I managed to 'lock' the control panel on my maytag dishwasher and i can't get anything to operate. The lights just keep flashing at me. What or where can i find the unlock code?


Hello. No problem. Press the START/STOP button to stop the machine. Then check your watch as it takes up to two minutes to unlock the door. Next pull the door indentation opposite the hinges. \015\012\015\012If the door still won't open, c ... Dishwashers

The controls on my GE GLD4600N10WW have on occasion locked up. In the past, I have resolved this by turning the breaker off and back on. It has now locked up, but won't reset. When the breaker is turned back on, the dishwasher control panel lights indicate "Normal Wash" and "Heated Dry" but the controls do not respond. After several minutes the lights simply go dark. It does not respond to any button pushing.


... Dishwashers

My kitchen aid kud 5255 hb51 dishwasher is not working...child lock light is flashing...?? cut off main to re set no help same thing is happening....child lock light flashes when i push cancel it too begins to flash


... KitchenAid Dishwashers

Hi I have a kuds255hbl1 dishwasher the lock light will start flashing after 30 sec. all lights will come on then all go off then lock lightwill flash again any help thanks dave


... KitchenAid Dishwashers

Whrilpool Gu3600XTS1 After a power surge the control panel pot scrubber and normal lights were flashing. I replaced the circuit board, thermal fuse and control panel. However, the lights are still flashing. what is the sequence of buttons do I push to reset the system.


... Whirlpool 24 in. GU2600XTP Built-in Dishwasher

The control lock light goes on as soon as I press the cycle to start the dishwasher. The dishwasher does not start, presumably because the control lock stays on. I do not know how to disable the control lock function. Pushing and holding the button for 3 seconds does not disable it.


Hello &\015\012Welcome to FixYa\015\012\015\012To unlock the\015\012controls press and hold the HEATED DRY button for 20seconds. If the problme\015\012returns then only option is touch pad replacement. Please get back t ... Maytag Dishwasher

I have a KitchenAid KUDS02SR dishwasher. If I push any buttons on the control panel the Normal light starts flashing rapidly and will not stop no matter what I do. While this is happening it will not start a cycle. If I turn off the power the light will stop flashing, but when I push any other button the Normal light starts flashing again.


The touch panel may have a bad push pad and will not let it probram there is a tech sheet under the dw just behind the toe panel this wil help you understand the flashing code . it will tell you what is wrong . but a ... KitchenAid 24 in. KUDS02SR Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0710 seconds