Having problems with your GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher ?

GE Quiet power 3. Model 400N10BB. When starting machine the lights are flashing, the machine starts, then after 1 minute the entire unit stops.


Answers :

Repair Help & Product Troubleshooting for GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

GE Quiet power 3. Model 400N10BB. When starting machine the lights are flashing, the machine starts, then after 1 minute the entire unit stops.


... GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher

I have whirlpool Dish washer model GU 120 ES (bought in 2001). When we start the dish washer cycle the unit starts for a minute, then the "start indicator" light flashes. As indicated in the instructions, we press the "start button" for five (5) seconds, at this time the washer clears the water out and stops. If you can assist this would be greatly appreciated. Thanks Jeff


I called the service tech.... ... Whirlpool Dishwashers

Maytag mdb9150 dishwasher stopped at some point last night--found it this morning with flashing lights--I think "clean" and "heated dry", not sure.  I used "drain/off" to make sure there was mechanical noise--there was, so I don't think the machine is dead.  Purchased on 2001 with 5 year warranty, so out of luck there.  I tried turning off the electricity to the unit for a few hours; nothing improved.  When you start it (or think you have!) it makes noises for about a minute that sound promising


Check pump and solonoids click/work, if no mechanical noise, could be the circuit board, but they can be expensive. :(\015\012if the solenoids click, and allows water in, then the pump might be jammed, with grit, clean and reinstall... good luc ... Maytag 24 in. MDB9150A Built-in Dishwasher

Hello, I have a Hotpoint aquarius dishwaher model no. FDW20 when the machine starts its cycle it stops after about a minute and the dryer light flashes along with the wash light, cann you help me. Peter.


Sounds like control switch is faulty. Check wires at motor first for corrosion or arcing. ... Dishwashers

Hi I have an F&P DW691 dishwasher (manufactured by whirlpool) the reser light is permanently giving two quick sucessive flashes and will not start the machine unless held on for 6 seconds, the machine then starts for a minute then stops and goes back to the two flash reset problem. Does any one know the fault code applications for this model.thanks Mike


Hi, I've got the same dishwasher but with a different fault, there's power down the cable to the d/w but no power lights on the front panel?Thanks. ... Fisher and Paykel Dishwashers

When cycle starts after about 1 minute bleeping starts and when door opens the machine has changed the programme to the 1st programme (rinse) the light is flashing 7 times then pause then starts again, it sounds like the water is not getting into the machine, we have checked the water pipes for blockage and cleaned the filters?? Model is ADG7440


... Dishwashers

Dishwasher model# FGHD2433KBI. washer was purchesed mid July, used 4 times. I just put in some dirty dish's and closed the door. A couple minutes later the washer turned on. No lights were on. After a few minutes I pushed the cancel button. Nothing happened. I opened the door and it sounded like a sucking sound and the pump stopped. No water in unit. I closed the door it started again. I cut the power at the circut box. Waited a few minutes and turned power back on. Power failure light came on.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

My kenmore dishwasher, model 665.16473300 has stopped working. Now the lights just flash at the Smart Wash, Normal Wash, and Cancel. I've reset the power and it just comes back. I've taken the drain area apart and made sure there are no obstructions. The buttons seem to respond, as after I reset the unit (breaker), only the Smartwash button is flashing. I push cancel and then it starts flashing. So I think the buttons work, but it's locked up.


IS THE WATER TURNED ON TO THE DISHWASHER ... Dishwashers

I have a 4yr old Smeg freestanding dishwasher. Model is DF612SDX. The problem is that a wash cycle will start but about 15 mins in it stops and 2 of the programme option lights (on the left hand side of the programme options), start flashing. If you open the machine the soap dispenser has failed to open. This problem has been a bit of a slow deterioration as we've had a number of washed that have managed to finish and then noticed that although the dispenser has opened it must have been to


... Smeg 24 in. DWF612SS Free-standing Dishwasher

My Frigidaire model GLD2155RDC1, installed in 2007, stopped working after we lost power. When we flipped the circut breaker back on the lights for Air Dry and High Temp Wash started blinking, but none of the other buttons work and when we open the door these lights stop flashing and there is no power for our machine. We tried tripping the breaker a few more times and it kept doing the same thing.


... Frigidaire Dishwashers

Kenmore model 665.15829 Air dry lock button light is on. Washer won't start. tried different codes to reset. no luck. when I pushpots pans button and start it goes into sensor mode and tries to pump out. after one minute operation it stops. The tub is dry no water in unit.


I have reviewed your problem and have the fallowing for you to aces.\015\012First, believe it or not, in some cases, when you get a power urge the unit will lock out and continue until a full reset is completed.\015\012Try di ... Dishwashers

Nordmende dish washer model no. DWSN60WH . when power button is switched on machine gives a buzzing noise for about 10 seconds while the start button is still lighting. Noise stops and light goes off and then wash and end buttons start flashing continuely.


... Dishwashers

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

Clean light comes on my Kenmore Elite Dishwasher Model # 665.17263. This happened once before and has to do with the heating element. The service guy showed me how to press the buttons in a certain sequence to "unstick" the unit and it worked fine. The Quick Rinse light keeps flashing. When I push a previous sequence recommendation it switched to pots n pans and Quick Rinse and Cancel all started blinking. Then in about 2 minutes went back to Quick rinse. I did one sequence and it started to d


It seems that there is something stucks in your dishwasher...is there any error code? ... Kenmore 24 in. 15079 Built-in Dishwasher

I have a Miele G1140 SCI Dishwasher. When I start it after a couple of minutes the Wash,Drying End Light starts flashing and the machine stops . Please could you advise me if there is anything I can do before calling someone to come and have a look at it.


... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

The start button flashing continuously and the filter area seems to be full of water but when I take it out it is perfectly clean. I have switched the machine on and off several times but each time the start button indicates a fault. I have tried holding down the on button so as to stop the start button flashing so that I could select a program - this did work once and I selected my program but 10 mins in it stopped and started beeping... I have a ADG7460 machine - HELP! I'm going crazy!


Please clarify what you mean by "..but when I take it out it is perfectly clean.." are you saying the water in the filter area is clean. \015\012\015\012Turn the power off and take out all the water by hand using a small container. Turn t ... Whirlpool Dishwashers

Just had new Frigidaire dishwasher installed. When cycle is started, display shows 99. Unit will fill with water, run cycle for about five minutes, stop and empty water then display a flashing PF. Can not seem to find a list of codes for this.


Pf is means power failure. ... Frigidaire 24 in. PLD3465REC Stainless Steel Built-in Dishwasher

Whirlpool model du1100xtpq6 machine will not start clean lite flashes 7 times stops and repeats must be code 7 blinks only drain pump runs when drain/cancel button pushed


Hi, this is an indication that the water did not heat properly. Follow this link to some instructions I put together to help solve this and reset the control so you can use the machine again. ... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

Dishwasher seems to start up as it should then after a few minutes it stops water is going in and pumping away it just doesn't seem to be pumping around the machine eco light is flashing


... Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher

Hello, I have a problem with our Miele G646SC Plus dishwasher. It starts its cycle OK, draining out any residual water, taking in fresh water and doing the initial rinse. After about 5 minutes it then stops with the "inlet/drain" red light flashing. The detergent is still in the holder and the water is still cold. The filter at the bottom of the compartment is clean, the drain pump spins freely. I've also checked for any leaks in the bottom of the machine that would trip the styrofoam/microsw


Hi\015\012\015\012 \015\012\015\012The light flashing means an issue while draining. You would need to check for air\015\012gap on the dishwasher, it may be clogged. It prevents dishwasher\015\012from drain ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

My panasonic range microwave NN-S255WF started to randomly beeping and flashing the potato/vegetable setting. For about 15 minutes the microwave keypad would not work at all. It is working again. The range overhead light on the bottom of the unit stopped working about a year ago - light will not turn on. Please tell me what the issue is, what would need to be replaced. The microwave is 4 years old. Thank you!!


We get microwaves in our shop frequently, this unit sounds as if it's brain has been damaged, I suspect, as it usually is that either the magnetron, or the High power Diode, has failed, this usually also, "Spikes" the "Brain" as well. At 4 years old ... Dishwashers

Dishwashing cycle starts for about 3 minutes then flashing LE light comes on and the machine stops. Why?


Display Condition LE = Motor ErrorPossible Cause For Error Occurrence:Wiring connection is OK?The Impeller of Washing Pump is locked.The rotor of Washing Motor is locked.The Blade is locked. ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

New dishwasher (Beko 2542F slimline model). Put it on for 1st time last night -when I got up this morning, the cycle which should have taken just over 2 hours hadn't finished. There's soapy water in the bottom of the machine which hasn't drained and the "wash" light is still on. Looks like the dishes are clean but hasn't moved onto the rinse/dry part. Followed instruction in manual to drain it (hold start stop button till lights flash and should drain in 45 sec) but nothing happened.


... Beko Dishwashers

Craftsman model 580.752020 electric pressure washer. First time I used it worked for about three minutes then the motor stopped. I cannot get it to start again. Plugged into a 15 amp gfi circuit which did not trip. The light on the plug is red as per instructions. Unit is beyond warrenty. What to do?


Turn off water and machine electrics.remove high pressure hose from front of machine, this may be tight if there is still pressure in the system.turn on water, when water comes out of machine hose outlet turn on machine. does the ma ... Electric Pressure Washers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1843 seconds