Having problems with your GE 24 in. GLD6560LSS Stainless Steel Free-Standing Dishwasher ?

Dishwasher displays 888 on LCD and Cycles through settings on own

\015 GE GLD6560LOOSS Dishwasher (only 3 years old)\015\012Worked great up until yesterday. The Start/Reset button was blinking, I loaded the dishwasher, put the detergent in and Pressed Start. It didn't start so I pressed it again, nothing happened so I held the button down thinking that was how to use the Reset. All the lights lit up quickly and the display reads 888 (which I read is some sort of display that shows with loss of power). When I close the door the dishwasher starts, but runs a cycle on it's own for about 5 minutes or so and then it switches to another cycle and runs that for a few minutes then switches to another and so on. The status lights aren't lighting up during this process, but the dishwasher is getting hot, running the water and such like it should be only it never progresses past the first few minutes so the detergent dispenser never opens. If I open the dishwasher it's steaming hot and everything is wet so I know it's at least operating, just not properly. I was hoping to find some sort of power reset button or tripping the breaker off and then back...no luck with that. I pulled the panel off and the toe kick panel, but didn't really know what to look for so I put it back together. When I close the door it's really weird it will start running immediately like it's in the middle of a cycle. It will go from say ''Pots/Pans'' and ''China/Crystal'' (lit at the same time mind you) and run that for a few minutes. Then it switches to ''Normal'' and say ''Express Wash'' for a few minutes, Then some other combo and so on. Never doing any of the settings for long. Is there any way to reset the panel, or stop the dishwasher from what it's currently doing? I've left the door cracked which is the only immediate fix to keep it from doing anything on it's own. Thanks for any help you can send my way. I'll keep searching forums and help pages in the meantime.\015

Answers :

Repair Help & Product Troubleshooting for GE 24 in. GLD6560LSS Stainless Steel Free-Standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher displays 888 on LCD and Cycles through settings on own


... GE 24 in. GLD6560LSS Stainless Steel Free-Standing Dishwasher

Model IGV 659.1 Dishwasher When switched on the 'time display' takes longer than 2 minutes to display the planned wash duration. The display works fine to set a delayed start. After cycling the start delay round to 0, or after RESET (buttons A and C pressed) the unit is then 'nudged' into displaying a time. After, at last, a time is displayed the unit works fine.


... Kuppersbusch Dishwashers

Frigidaire Gallery Series Dishwasher - unit stops near the final rinse cycle without draining - "ER" on front display, all led indicators on front display also lit (e.g. low rinse agent, etc.), and the "Hi Temp Wash" light is lit, regardless of cycle setting at beginning of cycle - rinse cycle seems to function normally


HI,check your drain hose first for kinks or food blockage also check the\015\012tail at the disposal or wherever you drain hose connects. Second there\015\012may be a blockage in the pump itself take it off and check. If all of\015\012thi ... Dishwashers

I have a zanussi ZSF2440 dishwasher, when it turned on by the power button on the front you can choose a cycle and start it, Once the cycle is started it fills up with water but doesn't stop until it over flows setting off the flood protection, which cuts the power, so all the lights on the display go off and stops the water flow and drains the dishwasher and keeps draining the dish washer while the flood protection is on. It seems as if the dishwasher doesn't know when its reached its correct


... Zanussi Dishwashers

Kenmore dishwasher 16934 will not start up for me. I can push any button to set the cycle(pots & pans, china gentle, quick rinse, normal wash) and the time shows up in the display, but when I push the start, two red horizontal lines appear in the time remaining display. Cannot get the machine to start anything. All cycle buttons give me some kind of time remaining display but as I said, it ends up with 2 red lines. Thanks in advance. Mark


... Kenmore 24 in. 16934 Built-in Dishwasher

Bosch SHU43 My Bosch SHU43C dishwasher stopped washing, turns out the impella came free from the motor, I repairded impella and put it back together and now the dishwasher washes great however now it is stuck in a wash rinse drain cycle. Display counts down but the unit never stops running when it reaches 0. Also, the water level is higher than normal and I there is a kind of thumping sound repeatedly every 15 seconds " use to make that sound only once at the start of a cycle before the impella


Sounds like the control module is out -- cost about $100 (I am on my third). I got a "lifetime" warranty when buying my second one. If you are handy, you can replace it yourself. You can call Bosch to confirm this (I did). It mounts inside the door. ... Bosch 24 in. SHU53 Built-in Dishwasher

Hi! We just installed our LG LDF8812WW built in dishwasher. We ran our first cycle and after the wash cycle the dishwasher displayed error code OE. I read that it meant there is a problem with the drainage, and to check the hose if it is kinked. Well, the hose is not kinked and we have no idea why it would have a problem with the draining. We have the hose set up per the installation instructions. How can we check to for something clogged? Any suggestions?


I actually own an LG LDF8812 myself, except mine is stainless steel, not white. So be it. :-)\015\012\015\012Anyway, it sounds like you have just unboxed the unit and it is brand new, not just new to you. I am also ... LG LDF8812 Stainless Steel Built-in Dishwasher

Our dishwasher model is a Nautilus FP920WW. The unit switches on OK and displays the normal wash cycle settings but when we try to start or change a cycle (or press any button for that matter) all we get is a quick, intermittent beeping and nothing happens/changes. Switching the dishwasher off and on again at the wall does nothing to solve this problem. What's going on???


... Fisher and Paykel Dishwashers

I have a Fisher and Paykel DW60CDX1 dishwasher, the display originally came up eith an error code for the door, which seemed to be the problem as it restarted with some pressure on the door, then it stopped again and now there is no LCD display and no action, cycle butten lights are on but will not make a noise when pressed. We live in the bush and cannot get a easy service option. Is there a diagnostics mode I can try, although the LCD may not work?


Old question, but for anyone else, hears the answer - http://www.recalls.gov.au/content/index.phtml/itemId/1015047This model has a product recall, minehas done the same as described above, recall issued Aug 2012. ... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

Zanussi dishwasher when cycle finished displays .60 instead of 0?


... Dishwashers

I have a Neff s4457n0gb/32 dishwasher that will not complete the cycle as it finishes on 0:01 minutes remaining on rinse and not moving to drying. I have to press the reset to clear the display to 0:00. If you've any idea how I can correct this problem that would be most helpful.


... Neff 24 in. S4457 Built-in Dishwasher

Hi there, my F&P nautilius dishwasher starts the cycle as soon as I push the power button but only pumps out then swithces off. It won't let me set or change the cycle. I turned it off and left it over night and in the morning it had overflowed with water. There is no fault code showing on the display either.


When you said overflowed with water did the water come out the door the float switch in the unit may be stuck either opened or closed which if it were stuck or the switch itself were broken then the unit would have water go in and immediatley go out ... Fisher and Paykel Dishwashers

My bosch sgs5312 dishwasher seemed to complete its washing cycle (Zero with a dot on the display), but the pump still seemed to work for hours. Tried to re-set to no avail. Cleared filters and the pu


... Bosch Dishwashers

Maytag Dishwasher Model MJD Jetclean displays E1 on LCD a few minutes into the wash cycle


... Maytag 24 in. Built-In Dishwasher w/ Jetclean III Wash System Dishwasher

The dishwasher will not do anything. The normal wash cycle led flashes and the lcd display shows --. I have reset the breaker and tried to reset the dish washer and still nothing.


What does the lcd show it says this -- in your post ? or is that all it shows is two dashes first thing to try is hold the cancel button for 5 seconds and then message me back with what the lcd shows i await your reply Thanks Rick ... Whirlpool 24 in. GU3200XTP Built-in Dishwasher

Electrolux 302 dishwasher. CL Child lock can not be removed using the instructions in the book. Wash cycle all mixed up. When set for reg wash 85 digital display said 85 now says 89. Also fan dry light is activated. When washing it goes from wash to rinse. When finished the dishes are fairly clean but wet as.


... Electrolux Dishwashers

Bosch dishwasher SGS45EO2GB/45 does not complete washing cycle. It stays at 1 min left with pump running. I have reset the machine twice at which stage the pump empties the machine and the display shows 0 mins. However, have tried it agin and same problem. Any ideas, please?


... Dishwashers

My Bosch dishwasher has several problems: 1) Water doesn't completely drain out and dishwasher kind-of smells when I open it -- I do keep the filter very clean. 2) The dishwasher takes HOURS to go through one load, no matter what the time says on the display and no matter what type of cycle you choose -- quick, delicate or regular. 3) The red display often displays something that looks like "2h" at the beginning of the cycle. 4) The place where you put the detergent doesn't shut.


Hi Kathryn .I think you have a defective pressure switch. The pressure switch is located near to the drain pump, and the device is used to determine when water had been drained completely.Also check the floater switch located ... Dishwashers

Dishwasher runs for appx 14 min & stops washing half way thru wash cycle. Timer contunies to run. No drain pump out (nothing). Let dishwasher set idle for appx 1 hour and it will re-set. Set timer forward to end of wash cycle and it will complete rinse and final rinse. Then go to dry. Timer works ok.


This sounds like something is stuck in the drain pump. You can remove the inner cover to look for obstructions. You have a dual purpose motor it does the both circulating and draining. The blockage is causing it to overheat and trip the thermal prote ... Whirlpool DU840CWD Dishwasher

Problem for Kenmore 24 in. 15992 Built-in Dishwasher Previously answered by Ginko but have not had any responses since June 18 and problem not solved. No water flow into dishwasher. Actual model is Kenmore Elite undercounter dishwasher 665.15982990. Float is not stuck. Worked fine for 10 years until mid May. Display shows cycle is on and counting, for all the different cycles. No valve or motor sound when starting cycles, only a single electronic click. When cycle is canceled, motor does s


Hi.Sorry about your old query.If there is no power on black wire and no filling, then check and eventually replace the thermal fuse. The thermal fuse is attached to control board. If it is faulty it will read continuity, norma ... Kenmore 24 in. 15992 Built-in Dishwasher

My Thermador dishwasher DWHD64EP/54 does not get the dishes clean. We checked all the usual things--water to the dishwasher is hot, filters clean, spray arms working and not clogged, detergent cups working, proper amts of detergent etc. We find that no steam is produced during the cycles, we find that the when choosing a cycle and power boost incorrect cycle times are now displayed compared to previous usage when the dishwasher ran normal. Some of the longer cycles now show only 24 min


... Thermador DWHD64EP Built-in Dishwasher

Kenmore 665.15912001 DISHWASHER RUNS BUT DISPLAYS ERROR MESSAGE Instead of displaying the number of minutes in the cycle when I push the cycle selector button and then the start button, it starts as soon as I push the cycle selector, without waiting for me to push start; meanwhile, it displays "_J" instead of the number of minutes in the cycle. It washes the dishes but not well, lots of food debris. Some people in this forum have described running a diagnostic on this machine; how do you do that


... Kenmore 15912 Built-in Dishwasher

Dishwasher Normally, after the dishwasher cleans the load, it displays green light next to clean. Once the door is opened, the light goes off an dishwasher is ready for next load. But from few days, after opening the dishwasher door, the clean light does not go off, it remains lit. Dishwasher doe snot reset for next cycle. So, I have to go in the basement and trip the main power to dishwasher. That resets the dishwasher. This needs to be done before each cycle. Not sure how to resolve the issue.


Make sure that you do not open the door during the wash cycle. Wait until all the cycles \015\012are complete before opening the door. Especially don't open the door \015\012during the drying cycle. ... Dishwashers

Incomplete cycle My Miele dishwasher (3 to 4 years old) finishes, leaving the dishes dirty and wet. It seems that it may only be running through part of the cycle - I'm not sure but from the time I set it going to the time it switches off, it seems shorter than usual. The dishwasher is not emptying as it has a pool of water in the bottom. I have tried various settings and have the same problem. the inlet/drain light DOES NOT come on. I have soaked up all the residue on the bottom and cleaned out


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

My kleenmaid dishwasher super silent model system DW5 doesnt appear to be heating the water on any cycle so it is not washing properly and leaving the powder etc on the glasses up the top particularly and also it does not go completely to the end of the cycle by itself(any cycle).Or completing the drying cycle. I have to switch to 0 cycle to make it complete the clicking to start again. What is the gauge on the inside of the dishwasher on the left that can be adjusted from 1-5 is this a heat


Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012Service manual, generic, use this to troubleshoot and repair.\015\012\015\012 ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2049 seconds