Having problems with your GE 24 in. GSD3630Z Built-in Dishwasher ?

Dishwasher started and then stopped when the door was opened and then closed


Answers :

Repair Help & Product Troubleshooting for GE 24 in. GSD3630Z Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Have a Bosch shy56a05uc dishwasher that suddenly stopped working to a point. I believe it is related to the door latch switch, because I don't feel the door securely latch shut when I close it, and I also don't get any cycle lights or times registered on the LED readout. If I depress the on switch, the drain pump will start even with the door open, and, depending on how long I leave the switch on, water will start to fill in the dishwasher, open or not.


Does your dishwasher electronic control or mechanical timer? if mechanical timer, I encounter a similar problem n change the mechanical timer. that problem solved.\015\012\015\012Prince P ... Dishwashers

My Frigidaire fghd2433kf1 starting flashing PF occasionally. I would open and close the door and it would go away. It became more frequent until two days ago when the dishwasher stopped mid cycle and flashed PF. When I opened and closed the door, everything went dead and the dishwasher no longer works. It acts like it has no power coming into it. I checked the breakers and the wires connecting the power into the dishwasher. No luck. I replaced the control panel, but not the control board. It did


... Frigidaire FGHD2433KF Builtin Dishwasher

My FDB2810Ldc1 dishwasher won't stop going thru the cycles. We have to open the door to stop it. When the door is closed again it starts and will continue for hours if the door is not opened again.


I tried this and it did not work I shut off the main breaker, and still continued now it fills up with water. itrn for 48 hours until i rubber band the door and I never turned anything on1 go figure I got rid olf a small perfect fine dishwasher becau ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

My CDA CW497 has developed problem. When i select a program say 70 degrees and press the start button and close the door the dishwasher starts in the the normal way bit after about 15 seconds the dishwasher stops making any noise and beeps once. When I open the door the green on/off light intermittently flashes. Any thoughts what the problem is please?


... Dishwashers

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

Tecnik DW2677 Hi, my dishwasher regularly starts to bleep after starting a wash program. When the door is opened it stops bleeping and the right hand light flashes 7 times repeatedly in sequence. By holding down the start and program change buttons together for a few seconds, it will reset. If you then close the door all is well for a few seconds the pump sound like it expells some water and then it starts to bleep again. The above process can happen several times before it decides to do what it


Check your water intake- i had the same issue - a leaky fitting wasn't supplying enough water to the dishwasher. had exactly the same symptoms you describe. fixed the leak, reset the dishwasher & it's working fine.\015\012\015\012\015\012\0 ... Tecnik TDW2677 Built-in Dishwasher

Dishwasher model# FGHD2433KBI. washer was purchesed mid July, used 4 times. I just put in some dirty dish's and closed the door. A couple minutes later the washer turned on. No lights were on. After a few minutes I pushed the cancel button. Nothing happened. I opened the door and it sounded like a sucking sound and the pump stopped. No water in unit. I closed the door it started again. I cut the power at the circut box. Waited a few minutes and turned power back on. Power failure light came on.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Hi - I have the Miele G 2470 dishwasher. It starts, and I have it set at "2 in 1 Tab" and on "Normal". I close the door and the machine makes a sound like it is starting, but then after abiut 30 seconds it starts alarm beeping and doesn't run. When you open the door it shows the light is now on next to "Intake/Drain". To stop the beeping I have to press the "off" circle. This sequence happens each time. what do you recommend to get it to work? thank you very much. Lori.


You could check into the User's Guide online manual below:http://safemanuals.com/414159.php?k=41da0c038c6dca28da72cf9056db1c61&ID=63815&q=MIELE%20G2470 ... Miele Dishwashers

My dishwasher thinks the door is open. i would start the wash and 2 min later it stop because it think the door is open. i open and closed it back but it does the same thing how can i fix it


The most common cause of this behavior is a failed or mis-aligned interlock switch that is part of the handle/latch of the dishwasher. Look closely at the latch and you will see the interlock.Good Luck! ... Whirlpool GU2400XTP Built-in Dishwasher

Asko 1585 Dishwasher. Lately the washer has not been completing it's cycle without going into the all lights flashing mode. Usually just opening the door, closing then pushing start gets it going again. Yesterday this happened and it was restarted as described, then it go stuck in what appeared to be a drain mode - all lights flashing, drain motor running. It was in this mode for several hours and could not be stopped by any means. Pushing buttons or opening the door had no effect. Even c


Hi\015\012\015\012\015\012\015\012Thanks for using FixYa. You are right it is related to a bad control board. The\015\012control board has gone faulty and needs a replacement. Please check this recall\015\012information--- ... Asko 24 in. 1585 Built-in Dishwasher

The dishwasher has the normal and economy wash lights flashing and after we hold the start button down for 4 seconds the stop and then return to flashing? The washer motor runs when the door is closed and no water comes out and the system doens't stop trunning until the door is opened. The system ran for over 4 hours yesterday. Viking Professional


Hello, welcome to ... Viking 24 in. Professional Series VUD040 Stainless Steel (Premium) Built-in Dishwasher

My Maytag Jetclean Dishwasher Model # MDB4010AWB Serial # 16163916uk is stoping midcycle, it doesnt make any noise or anything just stops. Water left sitting in bottom and have to open door then close to start again , stops again after a few minutes


Possibly a bad door switch losing contact, only after opening nad closing is it making contact again. part number for door swtiches and holder 99002254 retails for a about $25 ... Maytag Dishwashers

I have a fisher and paykel single door dishwasher model dw918 td. The other day its door spring collapsed and the door had a free fall. The dishwasher operated fine. But we have accidentally opened the door and let it free fall under its weight a few times. Last night the dishwasher began its cycle and stopped after 10 minutes - no beep, no alarm, display was fine. it just stopped. I opned and closed door a few times. Pressing the start/stop button only resulted in a beep but no action. I let


... Fisher and Paykel Dishwashers

Close the Maytag dishwasher, cycle starts, but I noticed a leak! Dishwasher door can be opened by putting your fingers on the edge and pulling it open. Tried it again, door clicked, thought it was ok but still could open door with fingers. Emptied the washer, door locked. Put in a few dishes, same problem


Your problem appear to me like it come from your upper basket .\015\012pleas try 1st to ensure the basket goes inside\015\012untill the end it is important..\015\012 thank you ... GE Dishwashers

My Maytag dishwasher runs part of the cycle,then stops. If I open the door and close it later it will start up again.


... Maytag 24 in. MDB3700 Built-in Dishwasher

Dishwasher started and then stopped when the door was opened and then closed


... GE 24 in. GSD3630Z Built-in Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I have F&P DD603 with problem with bottom draw. Once a programme is selected and door is closed, the dishwasher beeps three times then tries to start itys cycle. It then starts but stops every 1-2 minutes (like pause botton has been pressed). If you press start again it starts for 1-2 mins then stops again. I have tried turning off the power and totally cleaned out the dishwasher but no change? Any suggestions?


Hi \015\012When you pull out the drawer, pay attention to the bottom near the bottom front panel, you will see a little tab. this tab is at both sides of the drawer, press these tabs in and pull the drawer fur ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Myy kitchenaid dishwasher model kudi01flss doesn't start even though the lights on the panel light up so I opened up the door to look at the latch and found a broken plastic piece that appears to be part of the latch. Could this be why the machine doesn't start. The funny this is the door still seems to snap closed even with this broken piece but what I'm thinking is that this piece activates some sort of electrical connection that turns the machine on when the door is closed. Any thoughts on th


... KitchenAid KUDC25CH Dishwasher

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

I have a bosch SHU8815UC dishwasher. It was already installed when i moved into my apartment - so I'm unsure of the age. The dishwasher isn't functioning. When I open the door, the "Clean" light and the PowerScrub button are red. When i close the door, the light go off but nothing happens. One time I closed the door, it started to rev up but would shut off and beep three times after about 1 min. No water comes out. Any ideas? Thanks! June


... Dishwashers

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

Bosch Shu43C02UC dishwasher fills with water but the washing won't start. As the filling nears complete, a double clicking noise occurs to start the washing motor but nothing happens. The time continues to countdown but the machine is silent. When I open and close the door, the click click noise is heard but the machine is silent. I can cancel the cycle and drain the water but none of the washing or rinse cycles will activate but the timer works. The soap door even opens if the timer is left to


Have you checked the inlet water temperature is at the correct level for the dishwasher.\015\012\015\012Please provide the full model no. of your dishwasher -- Shu43C02UC /??\015\012\015\012I think the problem is linked to th ... Bosch 24 in. SHU43 Built-in Dishwasher

My maytag quiet series fills with water and then starts for 5 seconds then stops. This happens 4 times and then the entire system just stops. To help troubleshoot I used a screw driver to trigger the closed door so that I could leave the door open when the cycle starts and the pumps seems to be working and water sprays all over the place. I also took apart the impellar blade to make sure there was nothing jammed and everything is clean. Maytag MDB7500AWW


... Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1758 seconds