Having problems with your GE 24 in. GSD4020Z Built-in Dishwasher ?

Doesn't run Turned on dishwasher. It started normally and ran for a few seconds, then stopped and has not run since. I've noticed a few things happening recently: Water flow does not start right away so I turn the button until it does. Occasionally, the dishes don't clean properly. The dishwasher is 17 years old.


Answers :

I asked for help when the dishwasher (GE 1991) started up and then quit. Your site was useful as we found a priority list of things to check, thus saving much time and confusion. Our problem turned out to be a disconnected ground wire.

Thanks for the help. You probably saved us a couple of hundred dollars for a repairman. We intend to replace the dishwasher next year when the kitchen is renovated so the timing was important.
Repair Help & Product Troubleshooting for GE 24 in. GSD4020Z Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Doesn't run Turned on dishwasher. It started normally and ran for a few seconds, then stopped and has not run since. I've noticed a few things happening recently: Water flow does not start right away so I turn the button until it does. Occasionally, the dishes don't clean properly. The dishwasher is 17 years old.


I asked for help when the dishwasher (GE 1991) started up and then quit. Your site was useful as we found a priority list of things to check, thus saving much time and confusion. Our problem turned out to be a disconnected ground wire. ... GE 24 in. GSD4020Z Built-in Dishwasher

We have a Kenmore Ultra wash dishwasher Model # 665.13733K601 and serial # FW18136133. came home from work yesterday and the pots and pan button and the normal wash buttons were flashing alternately. When I pushed the cancel button it started to flash, then I pressed the smart wash button and now its flashing. I turned of the breaker for awhile and then back on and the lights weren't on right away but later started flashing again, and I can't get the dishwasher to do anything. Any help on my pro


Hi,\015\012That unit took a power surge and the control is now bad....those controls can all of a sudden go wacky and the usual cause is power problems...\015\012The only way to fix it will be to replace the control...\015\012 ... Dishwashers

We lost power as our dishwasher was running. When power was restored it seems to be stuck in the drain cycle. We have tried turning the unit off and back on and also holding the start button for 5 seconds.The 4 lefthand lights blink on and off and the right hand lights are steady. It is a model D1996.


Try to unplug it or turn off the circuit at the electric box.............wait ten minutes or so and plug it in and try again..................the program needs to be reset in that manner sometimes....... ... Dishwashers

I have a zanussi ZSF2440 dishwasher, when it turned on by the power button on the front you can choose a cycle and start it, Once the cycle is started it fills up with water but doesn't stop until it over flows setting off the flood protection, which cuts the power, so all the lights on the display go off and stops the water flow and drains the dishwasher and keeps draining the dish washer while the flood protection is on. It seems as if the dishwasher doesn't know when its reached its correct


... Zanussi Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I can't get my electrolux dishwasher to run. It seems as though the touch pad is not responsive. It says to reset holding down the sanitize button, I do that it beeps but doesn't do anythng. All of the buttons are not lit up. I have to hold the delay start button along with the sanitize button to light the buttons up, still the buttons don't seem to be responsive, I touch the start and the lights go away and flashing numbers appear. Et 19 66 02 34 Any help would be appreciated.


... Electrolux EIDW6405HT Builtin Dishwasher

My dishwasher, a Whirlpool ADP 931, has stopped working. Possibly because the door was opened during operation, right after it was started. There is some kind of error condition indicated through a blinking Start light, but I don't know how to analyze this. This is a quite simple model with very few buttons to press. When I turn the program knob right to start it, the only thing that happens is that the green Start lights begins to blink continuously. There is also another green light


Hello & Welcome to FixYaThis light is reset by pressing two buttons in sequence 3-4 times, to reset your dishwasher press these buttons in sequence:High tem ... Dishwashers

When i push the normal wash then the start button- the dishwasher turns off, when I push the start button, it runs the 2 minute drain cycle.


... Kenmore 24 in. Elite Built-In Dishwasher w/ Ultra Wash Filtration

I have a zanussi tempoline dishwasher, I have loaded this as I usually do, turn the knob to the right and select the 2nd programme the light next to this comes on, I have pressed this to start the machine although it seems as if it is going to start this light flashes and the top arrow on the right of this flashes intermitanly, but the machine does not start the wash programme. The 3hr delay button if I had pressed this by mistake which I am sure I have not would light up. When I found it did no


Hi Ruth.The machine can be in error mode. In this case one or more lights in the control pad will stay on or flash and the cycle will not start.One of the most common fault in your situation, and at start of the cycle is no wa ... Zanussi Dishwashers

When starting my GE Dishwasher I made a mistake & pushed the start button twice, now the cycles are all out of sync, what should I do to start it? It will run but sounds like there is no water in it. I pushed the reset button,but turned it off, because I was afraid I would burn it up, with no water coming in.


Push and hold the reset button for about 15 seconds should be ok,if not do same with start botton.adrian,,,,, ... GE Dishwashers

I have a Gallery 900 series GLDB958AS dishwasher. The cycle status lights (just right of the "time remaining" status window) continually blink. None of the buttons on the front panel work and every 10 minutes or so the water pump starts up for about a minute then shuts off. No water enters the dishwasher. I tried turning the power off then on but there is no change. Every so often a random cycle light will blink or light up for a minute, then turns off.


It seems that there is error on the program controller unit. All you need to check if that if there is moisture build up on the panels thus causing the programs to go harewire.\015\012So remove the panel and disconnect the wires, check all lead ... Frigidaire 24 in. GLDB958A Energy Star® Built-in Dishwasher

My dishwasher will not start. If you unplug it and plug it back in it says 1H, no matter what button you press it then says 2H and if you press another button it will say 3H until it runs through to 9H then will display --. It will continue to do this until you leave it alone and walk away. Then after a few moments it will clear itself out and the 'Normal' light under cycles will continue to blink. The dishwasher is 3 maybe 4 years old. Please help, I have a 3 year old and an 18 month o


Hi,There could be Few Possibilities.Let's try to Reset. 1h, 2H -----9H usually shows delay X hours Display where X would be 1,2...9.Turn the Power OFF for few minutes, say 5 Minutes and then Turn it ON. ... Dishwashers

Model 8573025-after being away for several months, I tried to run the dishwasher, and the lights started flashing, and it wouldn't start. Now it doesn't respond at all when I press the "normal wash" or "heavy duty wash" buttons, they will flash, but no other buttons respond at all.


When dishwashers get used after a long gap the seals dry out and start leaking or it could be moisture inside the switches. \015\012\015\012I will need the make and full model number of your dishwasher. Is it a Kitchen Aid? better to give ... Dishwashers

My daughter accidentally turned on our GE GLDA690 dishwasher. I can't seem to cancel it out without actually starting the cycle. I opened the door before the cycle started but now it is sitting there beeping. The obvious thing is to load it with dishes and run it. But it is just the two of us and we don't really have a load full. Owner's manual is no help. Even turning off the circuit breaker will not stop this infernal beeping. How do I cancel it? Why isn't there a cancel button?


... GE GLDA690MWW / GLDA690MBB Built-in Dishwasher

We have a new Whirlpool Dishwasher Model GU3200XTVY3, serial # F00404693 bought in April 2010. Yesterday,when we pressed the "normal" button, it started flashing then when we pressed the "cancel" button, it started flashing also. The dishwasher will not start when we pressed the "start" button. We tried to reset by turning off the power to the dishwasher and then turned it back on. All lights were off and then we pressed the "normal" button and it started flashing again. When we tried to pr


... Whirlpool 24 in. GU3200XTPS Stainless Steel Built-in Dishwasher

Dishwashing liquid ( Cascade Liquid- gel- with Dawn) seems to be crytalizing is dishwashing reservoir on the door. After running the dishwasher the small door holding the liquid is open but still has some residual dishwashing liquid in and it seems to harden right away into a crytal like substance. Just started doing this. Is it the product or dishwasher? The dishes come out clean. This product doen't seem to clean as good as the first cascade. Thank you


Tide is having a problem with it freezing during shipping. Call for a free replacement. Or...to thaw it she said to put it in hot water in a sink for one hour, then do it again (not boiling...have lid on tight). ... Whirlpool Dishwashers

Whirlpool - Quit Partner I - DU1048XTP: Start at the beginning - Dishwasher would go through most of it's wash cycle and stop and the 'Start/Resume' LED would start flashing. Would press 'Start/Resume' and wash cycle would start again and run non-stop. Would have to hit 'Cancel/Drain' to stop. Called local service tech and he said board would need to be replaced. First board he brought failed right away, second board was installed. Tech also replaced latch handle assembly because it was missing


Have you asked the technician if the water temperature is OK.\015\012\015\012Run it again and after 30 minutes cancel and see if water temperature is warm or not. If not warm enough, then likely causes are heater is faulty or if you are u ... Whirlpool Dishwashers

We have a Beko DWD5410W dishwasher that has worked fine...until today - the 'wash' light is on but it is not wasing. I have pressed in the 'start' button and held for 5 seconds to reset and it then springs to life draining out or whatever that noise is, and then if I turn the dial to a setting (even the cold prewash) and press 'start' again it starts whirring away, then after about 10 seconds just stops, with the 'wash' light staying on. Not blocked, I have checked - this likely to be a frozen p


... Dishwashers

My KitchenAid model number KUDSO2FR-SS hs blinking lights that won't shut off. The Pro Scrub light blinks on and off and won't shut off. I can sometime lock it out with the heat button but it lights right back up. After a couple of minutes the normal button starts blinking as well as the clean button. The dishwasher does not turn on. I tried unplugging it but it just reverts back to the same thing


... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

I have a GU1500XTLB1, type-575-0 Whirlpool Gold dishwasher. For the last couple of weeks I've been getting the control lock on. I got the manual out, I hold the air dry button and it clears. My problem is now when I turn the machine on dosen't matter which cycle I hit (pots and pans, normal, or quick wash) it runs for about 5 minutes and it goes into a mode with the timer having lines going horizontal with the air dry button lit up and rinse button lit up. It sounds like it starts the cycle


Hi,There are Few Tricks to Reset this. Follow the below Tricks :-1. Try holding down heated dry key for 5 secs. I believe that is the control lock/unlock button on your model. IF not, look for the lock symbol and follow same i ... Whirlpool Dishwashers

Electronic controls the dishwasher will not turn on. press and hold the heated dry button for 5 seconds and the machine came back to normal. now even that is not getting the machine back to normal. the normal button and start buttons flash but machine does not function. i have the front electronic panel off and do have a volt meter to test if you could run me thru the proper procedures.


First thing to check is the door latch switches, and hte strike plate(metal tab protruding from the top of tub assy in which the door closes into, if bent up to high the door will not be recognizedas being closed. you can use a small screw driver nad ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Start button flashes green but does not turn on. cancel button works for 2 minutes ( sounds like it is trying to drain) then shuts off. still can run the dishwasher. if I press any other button, such as pots and pans, the "time remaining" just has 2 lines. then it just repeats as above.


Most likely you have answered your question already... the drain pump is either obstructed or has failed... these units these days have plastic impellers inside and often go bad causing the drain motor to go bad... if the unit does not drain it will ... Whirlpool Dishwashers

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

Electrolux dishwasher all lights blinking and wont turn on push start button either all lights flash or normal light stays on  either case the dishwasher wont run a cycle


Remove the toe kick by loosening 2 screws. There is a panel there with little lights that correspond to specific problems. The light that is on will correspond to the problem that the dishwasher has detected. Correct the problem and you should be goo ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

Bosch SHE43M was running when a pipe broke under the sink and flooded the kitchen. Water turned off before dishwasher. Now dishwasher makes a motor sound but no water starts and no cycles. Nothing happens when pushing buttons 3 & 5 to reset


Water is in the base and the float switch is activated. you must remove the water to deactivate.then hit the drain and cancell. let me tell you a quick joke .Im a old bosch tech and i had a call with the same problem. as soon as i got there i notice ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2557 seconds