Having problems with your GE 24 in. GSD6660GSS Built-in Dishwasher ?

Rinse cycle continues after the door is open

\015 My GE Nautilus (model #GSD3200G00WW) continues spraying water even after the door is opened. The normal behavior is for the rinse cycle to stop once the door is opened. I'd like to fix this myself but I'm not sure which part is bad here. The door lock is fine and everything else is working fine on the dishwasher. If you have any ideas of which part needs to be replaced, it would be appreciated!\015

Answers :

It is good the hear that you checked the door latch. The latch has some sort of micro switch (interlock switch) that tells the DW control unit when the door is open/closed. Dismantle the door latch and look for that switch. It will have thin wires connected to it.

The switch may have failed, the wires may be disconnected.

Report back what you have found. OK?
There is a door interlock within the door assembly. I believe it's mechanically stuck rather than needing replacing.
\015\012
\015\012Turn off & unplug. You should be able to get to the internals of the door via screws around the edge. The interlock will be very close to the handle catch. Check operation by inserting a dummy catch to lock onto it.
\015\012
\015\012If it is stuck solid - order a replacement.
Repair Help & Product Troubleshooting for GE 24 in. GSD6660GSS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Have Whirlpool dishwasher Gold Series, Model GU9805CGB1 which stops part way through wash cycle with the led indicator blinks on the normal cycle.....if we ope nthe door and shut ...it continues until part way through rinse cycle...stops again....led indicator blinks again.....we open the door & shut and it continues....but then continues to run through the normal wash cycle continuously.....until we open the door again.....what's wrong???


Sounds like the door is losing contact with the door switch, first thing i would check is the door strike.Metal strike plate located on the tub itself that the door latch catches as it closes. its a spring metal striker, i would try bending it down ... Dishwashers

My Omega Eurolux Dishwasher (mode: DW211P/1) won't stop cycling, It sems to get stuck during the wash cycle and continues for hours, until I turn it off. If I turn the dial to rinse it rinses fine. It doesn't seem to heat the water at all, there is no steam when I open the door. I have put a new heating element in, but this doesn't seem to be heating up at all. When I open the door mid wash cycle the element is cold to touch.


... Dishwashers

Bosch Shu43C02UC dishwasher fills with water but the washing won't start. As the filling nears complete, a double clicking noise occurs to start the washing motor but nothing happens. The time continues to countdown but the machine is silent. When I open and close the door, the click click noise is heard but the machine is silent. I can cancel the cycle and drain the water but none of the washing or rinse cycles will activate but the timer works. The soap door even opens if the timer is left to


Have you checked the inlet water temperature is at the correct level for the dishwasher.\015\012\015\012Please provide the full model no. of your dishwasher -- Shu43C02UC /??\015\012\015\012I think the problem is linked to th ... Bosch 24 in. SHU43 Built-in Dishwasher

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

Rinse cycle continues after the door is open


It is good the hear that you checked the door latch. The latch has some sort of micro switch (interlock switch) that tells the DW control unit when the door is open/closed. Dismantle the door latch and look for that switch. It will have thin wires ... GE 24 in. GSD6660GSS Built-in Dishwasher

Kenmore Ultra wash makes a loud vibrating noise during the rinse cycle. Early on the noise stopped when you opened and closed the door. Now the noise continues throuhout the rinse cycle.


... Kenmore Dishwashers

Frigidaire dishwasher won't end cycle - will run on and on for hours. Sometimes it cycles through, usually it just endlessly washes and rinses. I have to CANCEL the cycle, which causes the dishwasher to empty and run a few RINSE ONLY cycles (which are consistent, cycle time wise) to rinse the soap off of the dishes. Also, the door for the soap seems to stick - how long into the cycle before the soap door should open? Also, does opening the washer during it's cycle (to add more dishes) change or


I would say the resettable thermostat has failed. There is a thermostat which senses the water temperature, and when it fails, it causes the dishwasher to run constant. Replace the thermostat underneath the dishwasher and that should cure problem. P ... Frigidaire 24 in. FDBB540 Built-in Dishwasher

I have a Whirlpool ADG937 dishwasher (9 years old) which will not complete a 65c wash cycle. It starts Ok and runs for a long time but then continually bleeps, when I open the door the programme indicator light is on the rinse cycle. If I reset the programme to 65c it may do the same or occasionally it will finish the cycle. I have tried salt top-up, descaling and filter cleaning all to no avail. Is the programmer faulty (can I bypass it?)or should I replace the washer?


... Whirlpool Dishwashers

When I started it, it made a loud grinding sound which continued whenever it was actually washing/rinsing. It was washing and rinsing the dishes ok. Eventually I didn't hear anymore grinding but the dishes had not been washed or rinsed. The detergent cup was open and the detergent spilled down the door. I ran it again and could hear the pump running. It ran through the cycles but the water was not being circulated. I suspect that something is caught in the disposer blade or something and is bloc


What is the brand and model number. it likely will have to be disassembled to clean it out. is it a built in dishwasher or a stand alone type ? ... Dishwashers

Kenmore elite dishwasher runs until it is manually shut off by opening the door? My Kenmore Elite runs continuously until I manually drain (cancel) the cycle. Then I have to rewash with no soap to simulate the rinse and again manually drain (cancel) the cycle. This was a $650 dishwasher. I am not sure how to reset the controller or even trouble shoot for an error code. Any suggestions?


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a GE Quiet Power 3 built in dishwasher. With 1 min. left in a cycle, I opened the door, removed an item, then closed the door again, but it didn't finish the cycle. The machine continued its single beeps to indicate the door was open. Reopened and closed the door. None of the buttons on the control panel respond. Have unplugged and left overnight, plugged back in, beeping continues.


... GE 24 in. GLD6500L Built-in Dishwasher

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

HI There, thanks for being willing to take my question. We have a 1 year-old White Avanti Dishwasher Model Model DW18/DW19PSS/DW181SS PROBLEM: detergent dispenser often does not fully open, leaving soap in the dispenser even thru the rinse cycle... it seems to get hung up on the upper rack. i can even hear the dispenser door pop open when i open the dishwasher after the cycle is complete, making me wonder if there is enough clearance for the dispenser door to flip completely open. THINGS I'V


... Avanti DW18 Built-in Dishwasher

Opened door on cycle, will not continue cycle after closing door


The most common problem for a dishwasher to not restart after the door\015\012being closed is a failed door latch interlock switch. Adjusting /\015\012repairing it is not too difficult.Of course this assumes that the Dishwasher power cir ... Bosch 24 in. SMU40 Built-in Dishwasher

Maytag model mdbtt70aww. After the end cycle. open the door and found detergent tab on the bottom and the main wash cover is opened. Maytag diswasher model MDBTT70AWW. Put dishes and so forth in the dishwasher. Put detergent tab and jet-dry rinse agent in the pre-wash section. and close the cover. Start wash cycle after done over door and found the detergent tab on the bottom new the heater. The cover to the main wash is opened. Dishes are are clean. Wish someone would tell me


... Dishwashers

When my dishwasher completes its cycle, there is powdered detergent left in the dispenser and the dishes aren't as clean as they use to be. This started happening after I ran a HI TEMP WASH with a SANI RINSE cycle. I'm thinking that either the detergent dispenser door is opening late or the water is not getting hot enough. To check the dispenser door, I left the door open and just poured powder into the dispenser compartment. This did not improve the cleaning.


Hi\015\012 \015\012Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doesn't allo ... Kenmore 16372 / 16374 / 16379 Built-in Dishwasher

Is there a way to have this dishwasher continue the wash cycle automatically after the door is opened? The kids always forget to press the start/resume button after opening the door during a wash cycle. This is for a KitchenAid KUDT03ST model dishwasher.


... KitchenAid Architect® Series II KUDT03ST Built-in Dishwasher

Maytag MDBH965AWQ I have a Maytag dishwasher model number MDBH965AWQ. A few weeks ago the clean and sanitized lights would not go off after the door had been left open for over 30 seconds. Then last week, the diswasher would shut off in mid cycle and all lights would turn off with water still in the dishwasher. Today, I noticed that I am able to open the dishwasher door while the dishwasher is running and it will continue to run like the door was never opened. Now it is starting to trip the brea


2 items in need of testing are the door switch - and the main controller board/timer unit.CLIC ... Maytag 24 in. MDBH965AW Built-in Dishwasher

Quit working during wash cycle, about 6 liters of water left in bottom, looks like it quit during rinse cycle. There is power to the door switch and door switch works shutting off power when door is opened. However the control panel does not respond to any push button. I have had a problem in the past with moisture from the door vent getting into the control panel area causing the push buttons to become eratic.


The capacitors in the control panel could be bad or have burnt out. Do check all connnections and if necessary, check the continuity of the power to and from the control panel with an ohm/voltmeter. ... Dishwashers

I have a 1999 bosch SHU 4300 dishwasher given to me. It worked great for about two weeks. Now it takes for ever *3-4 hours* to complete a cycle (if it does). I have opened the door to see it filled with sudsy soap after this long. I have checked the hoses and they are not kinked. Once the cycle of cleaning is over, If I reset it manually, it will rinse the dishes and empty just fine. But I have to manually get the dishwasher to advance to the rinse and dry cycle every time now.


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Kenmore Ultra wash 665 15895 dishwasher. It will not run any cycles. Symptoms: When I first close the door, the "Quick Rinse" light is on and the number 18 is displayed. When I push any button, the "Quick Rinse" light flashes continuously. If I touch any other button, both the "Quick Rinse" and "Pots and Pans" lights flash continuously. No matter what buttons I press, the behavior is the same. I've tried turning the power off and on, same behavior. The only button that doe


\015\012HiThis may be an issue with heater circuit, door switch or wash pump. Press and hold the heated dry/air dry button for 15 seconds....After, 5 minutes check if you are still getting the same error. If yes, ... Kenmore 15899 Built-in Dishwasher

My FDB2810Ldc1 dishwasher won't stop going thru the cycles. We have to open the door to stop it. When the door is closed again it starts and will continue for hours if the door is not opened again.


I tried this and it did not work I shut off the main breaker, and still continued now it fills up with water. itrn for 48 hours until i rubber band the door and I never turned anything on1 go figure I got rid olf a small perfect fine dishwasher becau ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

My wife opened door during cycle. When she closed door it would no longer run. Looking at problems and recomendations on similar models, I replaced the board. Did not fix the problem. I have checked the fuse and the door switches for continuity and all seem ok. The only lights on the panel that come on are: under cycle- Pots & Pans, Light. Under Options - Heated dry. No other lights work and the dishwasher does not operate.


Hi,\015\012\015\012First off, sorry to hear that you replaced the control board for nothing..in hindsight. So if I understand what you're saying is this, You cannot select any cycles and the unit won't start...because the start button is ... Dishwashers

My 6 year old dishwasher seems to be washing continuously. This has happened since the electrics tripped out last week. Cycles continue on and on and don't finish. also I don't think it's heating up at all. When I open the door there is water in the bottom but not tonnes of it, close the door again and it continues on but you never hear the drying stage.


... Neff 24 in. S5543X2 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1375 seconds