Having problems with your GE 24 in. GSD6660GSS Built-in Dishwasher ?
No drain not draining
There is a blocked pipe the easiest way to check is to take the drain hose and blow back in the machine and then switch on and see if it now drains.Try this and let me know if this solves you problem.
Repair Help & Product Troubleshooting for GE 24 in. GSD6660GSS Built-in Dishwasher
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Bosch SHX46A02UC-21 Won't Fill and Drain Runs Continually. Original presentation of problem was that it wouldn't drain. Discovered that Garbage Disposal had plugged drain line. After clearing Drain Line, now drains fine but the drain pump runs continuously and it never fills with water. Have done the Cancel, Power Off routine however, even after that, drain pump runs continually.
Float switch is in the flood position and the drain pump is running..\015\012there is water under the dishwasher or that switch is stuck up.. ... Bosch 24 in. SHU43 Built-in Dishwasher
Whirlpool Dishwasher Model #GU940SCGQ2 waste water from sink drain entering the dishwasher. Drain hose drains into same pipe as sin drain. Drain hose is elevated and looped as high as the top of dishw
... Whirlpool Dishwashers
I have a Bosch dish washer model SHX 43 M 0 ZUC / 48 FD 8709 00169 The dish washer is about 1 1/4 years old and was installed by a plumber as part of a Home Depot kitchen remodel. The problem is draining. The quick wash does not drain at the end of the wash. The regular wash sometimes drain and sometimes does not. The auto wash does drain. The lack of draining does not cause problems with the regular wash cycle. I checked the drain hose re the instruction manual and it is correctly installed.
Usually a brush with a flexible shaft will do the trick...\015\012\015\012Like this venturi tube cleaner (available where gas grills are sold)\015\012\015\012 ... Bosch Dishwashers
Magic Chef DU4K is not draining all the water. There's at least a gallon of water standing in the bottom. I have cleaned the air gap assembly and drain line completely. They were even sanitized in hot water. I do not hear the water draining like it use to. When it worked properly you could always hear water draining into the GD. Now I can hear any draining. Again, there is no clogging anywhere in the drain line assembly. Is it a bad pump. I don't know where to go next with this.
... Magic Chef Dishwashers
My Whirlpool wdf530payw dishwasher is not draining. I ran the service diagnostics using the control panel, and the code that came back was Function code 8, and Error code 2 "Drain Motor Electrical Problem". The possible causes listed are: a. Loose Connection in drain motor circuit, and/or open drain motor winding. b. Open Fuse on control to drain motor c. Faulty drain motor drive circuit on the control When I hit the "Cancel/Drain" button there's an faint buzzing sound for about 2 minut
... Whirlpool Dishwasher. Front Control Dishwasher in White WDF530PAYW
Subj: ge dishwasher mod/gsd3960looss - 1yr 4 mos old. problem: will not drain only used 6 times. last use after cycle done, water remained. had to hand drain. removed cover and checked drain area, no debris found. drain tube is connected to disposal by clear plastic tube; no clog in tube. the sink drains are clear and the disposal works normal. dishwasher drain seems to be stuck in closed position. this model has the touch pad controls. any solution????
... GE Dishwashers
Kenmore Ultra Wash Quiet Guard - will not drain at end of cycle. After cycle is complete, water (not clean) sits at the bottom of the washer but I still unload the dishes and then turn the cycle dial around again - going past all the water heating and filling and washing - and land on the drain cycle, it will drain. Any ideas why it will not drain when I let a cycle run, but will drain once I cycle it through to the drain option?
... Frigidaire 24 in. PLD2850 Built-in Dishwasher
Hi, I have a 10yr old Neff s5543 built-in dishwasher, it is has been working fine but recently has stopped fully draining. I have removed it from the housing and checked all pipe work is unblocked and not kinked, have also blown back down drain tube to free any blockages from drain pipe, have also removed pump cover and checked around impellor for any foreign bodies etc. Everything seems clean and free. I ran a complete heavy cycle (empty dishwasher) and allowed drain pipe to drain into a
Hello there and thank you for choosing fixyaOk there are acouple of things that can be checked on this along with what you have already checkedDrain solenoid\015\012 \015\012 \015\012 \015\ ... Neff 24 in. S5543X2 Built-in Dishwasher
The drain cycle does not drain completely. You need to restart it 6 or 7 times before it drains completely. When it first starts you can hear it draining but it only lasts for 5 seconds and then appears to stop draining. This is a Whirlpool Quiet Partner II Model DUL200PKT1
HiThanks for using FixYa. To start with try to leave the unit unplugged for 10-15 minutes and while its unplugged check for clogs in the drain hose. Usually, these issues are related to kinked hoses, ... Dishwashers
I have a bosch dishwasher SHE43C06UC22 (non-LED version). It's stuck in the drain cycle and continues to run even when opening the door (it should stop, but it doesn't). As a test, I poured a large glass of water in the bottom of the dishwasher and it drained it into the sink as it should, but it continues to run in the drain mode with no water in it. I've heard I either have a float stuck or an emergency drain switch or leak somewhere causing the dishwasher to continue in the drain mode. Ho
Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This can be caused by either faulty door switch or indeed the float you mentioned.\015\012\015\012This is where to look for the switch and test it ... Dishwashers
Bosch sgs43eo2gb dishwasher. wash programme completes, water drains out, but machine goes on draining, forever, stuck at around 50 minutes on the facia clock. there is no leak on the machine and everything else has been cleaned and operates perfectly. ie,fills correctly,heats correctly and drains fully but won"t stop draining & refill. Cancel programme and reset and it works perfectly until end of wash cycle again, when it continues to drain even with the door open. There is no leak in the machi
Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for\015\012using FixYa. Please once again check that the hoses are not kinked or drain pump and filter ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher
Dd601 ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the
I had the problem with the top draw not draining properly and the dishwasher showing the U3 fault code on my DD601 v.1, I did'nt have a copy of the dishwasher manual so it took the following steps, this is best done out side to save on messing your k ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
My Siemens SL84A305UC/21 dishwasher will not drain. I've checked the drain and it is clear. I can hear the motor hum during the drain cycle. It will fill and wash OK, but not drain. Does this machine have a solenoid for draining and if so how do I check it? How do I check the pump to ensure it is functioning correctly? I've tried to remove the plastic bottom of the machine to see what is inside and to troubleshoot the components, but it seems almost impossible to remove. What is the trick? What
... Siemens 24 in. SL84A305UC Built-in Dishwasher
My GE Monogram ZBD4500 dishwasher does not drain completely at the end of the cycle. If I run a couple of manual cycles afterwards it eill eventually drain completely. Drain hose is clean, pump suction sump looks clean, drain pump impeller appears OK, discharge check valve assembly is easy to blow through in direction of drain. Do I have a sequence switch problem?
I bloody lostt you! are you still there? ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher
Bosch SGS5312GB/12 Dishwasher I had a control board. Worked fine except didn't heat the water. Got it repaired (new PCB). Now the only thing it does is drain. Clicks every 20 secs and carries on draining. Got a new board. Does everything (including heat the water) except it does not drain before, between, or at the end of cycles. It does drain when while filling, and if the flood detection rod is raised manually (also drains if the inlet pipe beyond the pressure sensor is blocked - found
... Bosch Dishwashers
My Siemens SL84A305UC/26 dishwasher will not drain. I've checked the drain and it is clear. I can hear the motor hum during the drain cycle. It will fill and wash OK, but not drain. Does this machine have a solenoid for draining and if so how do I check it? How do I check the pump to ensure it is functioning correctly? I've tried to remove the plastic bottom of the machine to see what is inside and to troubleshoot the components, but it seems almost impossible to remove. What is the trick? What
... Siemens 24 in. SL84A305UC Built-in Dishwasher
Hi. I have a 3 year old LG dishwasher. It will not drain. Display shows OE. I completely cleaned the drain assembly inside the DW. I checked the discharge line, it is completely clean. I disconnected the drain line from the air vent assembly at the sink and ran the DW, still will not drain. I disconnected the discharge pump wires and ran current directly, the pump works. I replaced the main control PCB, still will not drain. Please advise. Thanks
Measure the electric resistance of the Drain Motor. (Value should be 20-40 Ohms) If it is out of spec, replace it.\015\012\015\012Please reply with what worked best. Thanks! ... LG 24 in. LDF 7811 Built-in Dishwasher
DD601ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the s
Check for restriction in sump. ie remove rotor, push pipe cleaner or similar from filter sump into rotor sump ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
Drain pump makes draining noise but does not drain water from the wasmachine. It drains water correctly when we use the switch for drain or when we use the switch for spinning. The pump does not stop running. What is wrong?
You will find this link useful. also read commentts and replies following it.\015\012http://www.squidoo.com/Bosch_Dishwasher_Drainage_Prob ... Bosch 24 in. SHE44C05UC Stainless Steel Built-in Dishwasher
My asko d3250 thinks the drain hose is blocked. but when i pour water in the dishwasher to see if the water is being drained, the dishwasher is draining properly. Yet the dishwasher after it has drained the water, will shutoff and start flashing the Large Pot icon (drain hose is blocked error code). Is there a sensor that is faulty?
Yes, it sounds like it is to me. I'm not able to pull your model up on my data base,if I could I would be able to tell you where it is located. I would assume that it's located either inside the pump or close to it. Sorry I couldn't be more help. ... Asko Dishwashers
I have a Bosch Diswasher that is not draining. I have disconnected power for 35 minustes and used shop vac to excess water out of drain line. i also pulled all water thru the drain line from the tub itself. i assume that because i could pull the water, all baffles and lines are clear as i emptied the tub from drain line. you can hear the pump come on to drain water but no water is moving. What would be my next step. If it is to replace the pump, how do i easiest access the pump to remove and rep
Either the selector switch or pump is faulty. If there is not any clogs anyways. The system may need to be reset. Most resets are done by entering a series of numbers on the touch pad to enter diagnostic/test mode where the machine can be reset. This ... Dishwashers
My brandt VF300 doesn't drain at the end of wash cycles. If you run the soak programme it drains fine. Some time ago the door was adjusted by an engineer, when he arrived he pressed some buttons which then drained the unit immediately, I have forgotten which buttons! Is there anything I can do to reset the thing, given it drains on soak I am doubtful the drain pump has broken ir is blocked?
There is gum stuck somewhere in my dishwasher drain line. The water won't go down. I took the inside apart and can see the hole where the drain water goes. I disconnected the drain hose under the sink. I got the water to drain out when there was alot in there, but now it won't drain again. I blew compressed air from a compressor backwards through the hose and it makes a big splash and bubbles inside the dishwasher, but the water still won't go down. I put Boiling hot water and vinager in there t
Ther e is noo easy fix, short of replacing the drain line( if indeed thats where the clog is)although you checked the hose from the under the sink, did you check with in the hole where the sink conection is made??and try disconnecting the drain hose ... Dishwashers
I have a Bosch Dishwasher- I installed a new garbage disposal and forgot to knock out the drain plug (dumb-i know) and I ran the dishwasher that night- well in the morning I noticed it was full of water and the bottom and the drain was humming. I then realized what I had done- so I knocked out the plug and the dishwasher drained immediately. but now the drain continues to run - even with the door open and I cannot get it off the drain cycle. Any suggestions?
\015\012If you notice still any water in the base. you sponge out the water and then check turning ON the dishwasher. If still the same problem then two possibilities \015\0121) bad water fill value. ... Dishwashers
The dishwasher isn't draining properly. Not a blocked drain problem as the washing maching draining via the same drains is OK. The bottom of the dishwasher is half full of water that isn't draining on its own.
Sounds like you have a bad drain solonoid very common problem and easy fix. ... Neff Dishwashers