Having problems with your GE 24 in. GSD6660GSS Built-in Dishwasher ?

My GE triton dishwasher wont start when I press the start button


Answers :

Repair Help & Product Troubleshooting for GE 24 in. GSD6660GSS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My GE triton dishwasher wont start when I press the start button


... GE 24 in. GSD6660GSS Built-in Dishwasher

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

With Kitchaid dishwasher KUDS01FL, it wont run. All control buttons seem to work (by lighting up when pressed) except "start". When press "start", it doesn't blink or start. Does this indicate a bad start button switch or something else? Is this something I can replace? Thanks.


Hi Thanks for using FixYa. To resolve this you will have to reset the console. Do this by closing the door and press these buttons in sequence...-high temp wash - ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Hi. Got a dishwasher from IKEA - Whirlpool DWH B00. It wont run anymore, 2 years old. It just wont start up, it starts to give a beep, and the solution is to press the <|> button for 2 sec, then restart it. But it still wont start. I've cleaned all filters, checked for water on board underneath, and given it some salt - no luck. Any ideas?


... Whirlpool Dishwashers

Whirlpool adp 5550 Dishwasher wont complete a cycle. The light in the start button flashes four times in a continuous pattern. Have pressed the start button for 3 -5 seconds to reset after which the machine seems to operate ok then it stops and the start button returns to flashing. Have cleaned the filter and checked the sullage pipe for blockages What do I do next?


... Dishwashers

We have a new Whirlpool Dishwasher Model GU3200XTVY3, serial # F00404693 bought in April 2010. Yesterday,when we pressed the "normal" button, it started flashing then when we pressed the "cancel" button, it started flashing also. The dishwasher will not start when we pressed the "start" button. We tried to reset by turning off the power to the dishwasher and then turned it back on. All lights were off and then we pressed the "normal" button and it started flashing again. When we tried to pr


... Whirlpool 24 in. GU3200XTPS Stainless Steel Built-in Dishwasher

I purchased a second hand Electrolux Dishlex DX403 with a kitchen. The dishwasher turns on when I turn the powerpoint on and makes a noise as if it is about to start. I attempt to press the buttons to set a mode and start it and it wont work, the buttons dont do anything. How can I fix this?


... Electrolux 24 in. EDW5505EPS Stainless Steel Built-in Dishwasher

ASKO dishwasher D3122 drain pump wont stop pumping and the machine wont respond when we press any of the program or start/stop buttons. the program light is flashing. We can turn the power off with the main switch on top of the door but when turning it back on the pump starts pumping again. please tell me how to fix this problem so we can get it up and running again.


... Asko D3122XLSS Stainless Steel Dishwasher

Hi there. I have a Matsui MF145 slimline dishwasher and having a problem. When I press the on/off button I would usually then press the program indicator button (usually the first indicator - pans) and close the door and the dishwasher would start. Currently i press the on/off button and try to press the program indicator button and the on/off button flashes and there is a continuos beeping sound....and nothing more happens. Do you know what the problem is?


Try to clean the unit, ofetn when the machine is dirty, some sensors are fooled thinking there's some problem. be sure there's no jam on mechanical parts. ... Dishwashers

I have a F&P dishwasher model DW60CDX1 (around 5 years old) which we cannot start a cycle. The dishwasher turns on (power button and all programme indicators light up) but when you press a programme button nothing happens - the lights don't change. We have switched the power off at the powerpoint and on again a few times but this has not rectified the problem. It was playing up before this in that sometimes the programme would not start when a button was pressed but I just closed the door mor


The micro switch in the door which senses the door closing has probably failled. This is accessible once the inner door cover is removed. Switch should be under $10 from electrical store. Or buy through appliance manufacturer. ... Fisher and Paykel Dishwashers

Hi, I have a KitchenAid Superba diswasher model #KUDSO1FLSS2 that has quit working. All the buttons seem to work and the lights light up as they should but when you hit the 'start' button the light that you selected for whichever cycle would flash once, then close the front door and dishwasher would start. The 'start' button was acting up and would have to press a few times before light would flash and then the dishwasher would work. Now everything lights up but start button does not work. Opene


Hi.Test the start button switch.The switch is tested by disconnecting power and reading Ohms, this will tell you if it does open and close the circuit.If the start button is part of the control assembly, then this kind o ... Dishwashers

Baumatic (BKD62SS or BKD62W .3) Dishwasher will not do a normal load but will run in a strange start up mode I found. When I press the power button, select a cycle, then press start the dishwasher will no longer do anything. 5 seconds after pressing start it will make a light hum noise, a little like heating water. After about a minute the dishwasher won't have done anything. It will then beep 30 times with the third led on the set of four (don't know what it means) will flash a lot. The beeps t


... Dishwashers

KitchenAid KUDI10FL dishwasher- The door spring system broke and I repaired it, but now all of the sudden the dishwasher will not start. The door may have been dropped a couple of time before the spring system was repaired, but it did not hit the floor, just a hard sudden stop. All of the cycle setting lights come on when they are pressed except for the start button. Just before the start button stopped working the dishwasher started by itself or started several hours after cycle selection had b


Hi- It is possible that the door latch is not completely engaging. If the door dropped the hinges may have bent a little thus preventing a good contact with door switch. Try pressing and holding the door shut, hard, and pressing start. If that wor ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Dishwasher keeps stopping and beeping continuously until I press the start button again and shows the F8 Code. When I press the start button it continues for about 5 minutes and then stops properly but there is lots of foam still in the bottom of the dishwasher.


Sir i think the problem would be in any of the three areas. any prob in these areas would lead to the problem u specified\015\012\015\012Test the timer motor.\015\012 ... Dishwashers

Prima lpr601 problem- filled dishwasher up sa normal set the wash pressed button on far right (dont know what it is but needs to be done), closed door and loud raattling so i opened door to make sure all spray arms were clear which they were, closed the door , again the rattling . now the green light has gone out on far right and cant get it back on so program wont start at all. Any advice?? please help


... Dishwashers

Model # KUDP01FLSS5 Dishwasher has power. Normal button lights up but start button wont light and wont start dishwasher


Please check the internal connections. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

I have just moved house and there is a bush integrated dishwasher WQP 12-9348 with no intructions. I have used it twice with guesswork but just turned it on and pressed the button next to the display and it wont start but keeps beeping every few seconds


... Bush Dishwashers

Viking dishwasher M# DFUD142-PSS drains a little bit only then starts refilling, start button is blinking. When pressing the 2 buttons to drain have to press several times until responding then it drains just fine, also no push button light is on when pressing for drain. After doing all this machine worked fine for one wash only, then the same problem again after the wash cycle the water stays in the machine. Please help, thank you


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

When I depress the start button, the timer is clicking to engage and begin the cycle, however, the dishwasher does not start. Other times, there is no noise whatsover when I press the start button and neither does the dishwasher start. If I don't use it for say 2-3 weeks and try again, it starts working for a period of a few months, but then the same thing happens again down the track. This has occurred about 4 times.


Hi.Resetting the breaker means turning power off and back on from the main switch in your house. Same as disconnecting power cord.I am sure that in this case "tripping the breaker" will not help. Repairing appliances is not th ... Dishwashers

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

We have a Kenmore Ultra wash dishwasher Model # 665.13733K601 and serial # FW18136133. came home from work yesterday and the pots and pan button and the normal wash buttons were flashing alternately. When I pushed the cancel button it started to flash, then I pressed the smart wash button and now its flashing. I turned of the breaker for awhile and then back on and the lights weren't on right away but later started flashing again, and I can't get the dishwasher to do anything. Any help on my pro


Hi,\015\012That unit took a power surge and the control is now bad....those controls can all of a sudden go wacky and the usual cause is power problems...\015\012The only way to fix it will be to replace the control...\015\012 ... Dishwashers

Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che


... Dishwashers

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2152 seconds