Having problems with your GE 24 in. Monogram ZBD6880KSS Stainless Steel Built-in Dishwasher ?

The door handle on my GE dishwasher is loose. How do I remove the door to tighten?


Answers :

Repair Help & Product Troubleshooting for GE 24 in. Monogram ZBD6880KSS Stainless Steel Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Jdb2100aws dishwasher - door handle fasteners loose, handle ready to drop off. This is a dissambly question: The middle section of the door has an upper one-third (which contains the input switch strip) and a lower two-thirds; the upper section must be removed to tighten the door handle fasteners. After wiring is disconnected (yes, power is OFF), the upper section appears to be held to the shell by some kind of barbed fastened from the inside, run through a tab on the door shell and into a fema


After removing the stainless cover l tried to disassemble the door further but found it difficult, there is a hard thick plastic cover, i took my dremel and cut a small hole large enough for a wrench to fit and tighten the thin nut on the handle, lin ... Jenn-Air 24 in. JDB2100AWS Built-in Dishwasher

I have a GE profile dishwasher with the controls on the door edge. my handle for the door has become loose on one end. how canI tighten the handle. doI have to remove the entire panel on the door back?


... GE Profile PDW8060GSS Built-in Dishwasher

The door handle on my GE dishwasher is loose. How do I remove the door to tighten?


... GE 24 in. Monogram ZBD6880KSS Stainless Steel Built-in Dishwasher

Jennair dishwasher - model JDB-5 with stainless steel front with stainless bar handle. The left hand side of the handle has become loose. How do you take the door off to tighten screw. I tried by removing all the interior screws and lifting the first plate off. That brings me to the electronic circuity but not to the screw port. Please advise


... Dishwashers

I removed door panel of Bosch SHV4803UC dishwasher in order to tighten the door handle. Now the the diswasher won't run the cycle, but the lights are on.


... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

The cabinet handle that is on the wood cabinet door cover is loose, I need to remove the cabinet door, tighten the knob and replace the door


... Miele G2183SCSF Builtin Dishwasher

How do I tighten the loose door handle on my Bosch SHX46A05UC/14 dishwasher?


... Bosch Dishwashers

Bosch Dishwasher I have a stainless steel Bosch dishwasher, I made the "mistake" to try to see if I could fix the jammed handle from the door. Unfortunately, (did not realize the top panel comes off without opening the entire door). I removed the screws from the door frame (Inside panel), and the door springs/latched got loose. I would like to put it back together, but I dont have any diagrams on the door to make sure all parts are in place to put the door back together. I have been havin


Hi ED,\015\012\015\012It sounds like a real problem here. If the springs are still in one piece, my best guess is to to remove the springs from the door. Then attach the springs to the dishwasher body first, then reattach the spring to the door. Not ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

I ordered a stainless steel door panel (SGZ1005UC) for my Bosch dishwasher (SHV45M03UC) and the installation instructions are minimal and the diagram does not match the door. I can attach the handle, but do not know if I should remove the partical board that is in the door when it shipped. Also, there are no pieces protruding that I can see for attaching the door.


Did you ever figure this out? I just got the door and have the same questions! ... Bosch Dishwashers

Handle broken on indesit integrated dishwasher do i have to remove all the screws on the inside of the door to replace the handle?


... Indesit 23 in. DV62 IX Built-in Dishwasher

The handle on the dishwasher is broken and the door doesn't shut all the way. I removed the screws to look inside and there are wires that go into this component that is connected to the handle. Is this something I can fix? How would I find the parts.


... Amana 24 in. ADB2500AW Built-in Dishwasher

How do I tighten the door handle on my Bosch dishwasher model SHY56A 05UC/14?


Remove front panel then you can access the handle screws. Open the door and remove the 'torx' screws surrounding the perimeter of the door. ... Bosch 24 in. SHY56A05 Stainless Steel Built-In Dishwasher

Handle on BOSCH Dishwasher Model SHX46L05UC/18 became loose and now is off on one side. How do we get into the door to put the screws back where they belong and tighten.


To fix the door handle, first you need to remove the outer door, open the door and remove the T-20 Torx screws located on each side of the inner stainless door. \015\012 \015\012Return the door back to its\015\012upright position, and bri ... Bosch Dishwashers

Front panel My dishwasher wouldn't drain. I read I had to remove the front panel under the door and get to the hose to look for a blockage. I screwed out two screws on the side of the dishwasher and removed the white front panel just under the door. But then there is another metal panel and I can't loosen it. Is it just stuck or is there soem way of doing this? Elmi


Did you knock out the plug on the disposal before you hooked up the drain hose ? ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Loose handle on frididaire gallery series dishwasher


Handle needs to be replaced part# 154537303 (blk). Un plug unit, take 4 screws from behind blk control panel out. Panel will fold down, remove two torx head screws from door latch, replace with new one and put it back together and your done. ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Loose door handle on bosch integra ltd. dishwasher


You can loosen the inside of the door with a small torx screwdriver and lift it up far enough to get to the screw that holds the handle from the inside. I did this with mine about 1 year ago. ... Bosch Integra® 500 SHX46L Built-in Dishwasher

I have a Magtag dishwasher, model #MDB6650AWQ thats not running. I check the power supply all the way up to the door latch and it shows that there's power there. However the circuit panel not lighting up and nothing happens when you push the normal wash cycle or any of the other buttons. I believe the problems is electrical in the door latch handle. Is there any way to check the solenoids which are attached to the door handle before I order a new door latch.


I have the same problem with mine. It is 3 1/2 years old. The repair man was just here and said it is the control panel. It will cost $171.85 for the part and then $53.85 today for his visit and then a return visit when the part is in.\015\0 ... Maytag Dishwashers

I need to remove the furniture door off my integrated dishwasher


I have the same problem.I need to take off the door from the integrated dishwasher.I can see a possible screw on the either side of the door but difficult to visualise this to find out what kind of screw it is.\015\012Can someone advise me reg ... Tecnik 24 in. TKD795/3 Built-in Dishwasher

Hello,I hope you can answer the question below for me. My dishwasher is a Hotpoint model BFI680 - integrated. I want to replace the old interlocking assembly with a new one as the spring has broken and I can not close the dishwasher door. I have trouble removing the old interlocking assembly though. I can not see any screws that keep it into place as with other models. Instead, it looks like that it is "clipped" to the dishwasher door via the two inner side round holes at the bottom. Tried to re


... Hotpoint 23 in. BFI68 Built-in Dishwasher

Dishwasher door The door on my dishwasher has gotten skewed somehow. It is tilted toward the right and won't close. Is there a way to remove the door and adjust it?


Hi rrlady,\015\012\015\012 I'm Harvey the Master Plumber.\015\012\015\012Your question is: The door on your dishwasher has gotten skewed somehow. It is tilted toward the right and won't close. Is there a way to remove the doo ... Maytag 24 in. MDB6100A Built-in Dishwasher

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers

I have a Bosch SMU2042UC/14 dishwasher. The door will not latch. I have replaced the door latch and handle and still have the same problem. The dishwasher still works, will a little leaking, even though the door does not latch.


Is the latch adjustable? Have you checked your seals and your hinges? One of these has to be the cause. If you do not have the expertise to troubleshoot this problem yourself I would recommend a professional servicing the machine. If you need any oth ... Bosch Dishwashers

My husband removed the inner panel from the dishwasher door to see why the "door open" light was on after he changed the front panel from white to black. He shut the door without the inner panel and now we cannot open the dishwasher!


It would be helpful to have the full model number of the dishwasher.\015\012\015\012The trick would be to drag the dishwasher out from under the counter and open the foot plate and the spring assembly. Hopefully you may be able to lift th ... Kenmore Dishwashers

Hi. I have an LG LDF7810 dishwasher. I did a deep clean and ended up taking out a bunch of grease from the seal between the door-bottom and the tub. I even removed the door to get at the grease I thought was trapped back there. Since then it has been leaking water, sometimes a drip and a couple of times a few ounces have gushed out at the end of a fill cycle. Did I remove some factory grease designed to seal the door bottom? If so, what should I replace it with? If not, what else could the


It is possible that while you removed off the grease the water seal/oil seal was also damaged. Once the seal is taken out it can loose the sealing strength which can make it possible to leak.\015\012Hence it will be good to remove the seal and ... LG 24 in. LDF7810 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2041 seconds