Having problems with your GE 24 in. Profile PDW7800 Built-in Dishwasher ?

I set the cycle and push start and the breaker kicks off

\015 The dishwasher is plug in with my garbage disposal so I unpluged it and retried the dishwasher and still had the same problem.\015

Answers :

It could actually be the breaker itself. If not, there is a "short" in the machine. The likely place for the short is the water inlet solenoid valve which is replaceable. If not there, then you need to call the repairman.
Repair Help & Product Troubleshooting for GE 24 in. Profile PDW7800 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I set the cycle and push start and the breaker kicks off


It could actually be the breaker itself. If not, there is a "short" in the machine. The likely place for the short is the water inlet solenoid valve which is replaceable. If not there, then you need to call the repairman. ... GE 24 in. Profile PDW7800 Built-in Dishwasher

GE Potscrubber 1200h tempertature sensor The push buttons will not set (work) except for the Reset button...it goes in a cycle in about 30 seconds. Normal wash, etc will not set. They go a little over half way in but do not connect. When it first started we had to reset the GFI breaker.


Hi\015\012\015\012The issue seems to be with the control not working fine, it\015\012can also be due a bad control board. You can take it apart and check the\015\012control board, blow air with hair dryer on the control if bad replace it. ... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

Kenmore dishwasher 16934 will not start up for me. I can push any button to set the cycle(pots & pans, china gentle, quick rinse, normal wash) and the time shows up in the display, but when I push the start, two red horizontal lines appear in the time remaining display. Cannot get the machine to start anything. All cycle buttons give me some kind of time remaining display but as I said, it ends up with 2 red lines. Thanks in advance. Mark


... Kenmore 24 in. 16934 Built-in Dishwasher

Electronic control pad is pushed for quick wash and the LED display would show 52 minutes. Now when it pushed the display shows 17 minutes and performs all the functions that would occur at the end of a normal cycle. Can set for the longer wash cycle 94 minutes and performs all functions start to finish. Think the control board is bad any advise.


... Maytag 24 in. DWU9902 Built-in Dishwasher

Kenmore Elite - 9 Year old Dishwasher - A circuit blew and the dishwasher stopped in mid-cycle and did not drain.... I reset the circuit breaker and "manually" took the water out of the dishwasher. When I push buttons to restart the "95" shows up for the normal cycle. However, when I push start the "95" becomes a "--". Suggestions???


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Have kitchenaid dishwasher kuds30fxss3. When pushing start button, start button starts flashing and beeping. If I reset breaker in basement, it will run one cycle and then start flashing the next time. Any solutions?


... Dishwashers

My Kenmore Dishwasher won't turn on. Was working fine last week, but when I went to start it yesterday, nothing starts or lights up when I push the button. The options buttons still light up, but thats it, the wash cycles and the start and stop buttons...nothing happens. I tried tripping the breaker to reset and it did no good.


Hi,\015\012\015\012A device may cease to function or operate sporadically if the electrical cord is damaged. Inspect the cord for any damage. Check whether there are any black smudges or burn marks on the outlet, cord or anywhere the cord comes ... Kenmore 15129 Built-in Dishwasher

It does not matter which cycle is chosen, once "start" is pushed on our Asko D3120W the drain pump comes on empties the machine, then it fills for the first time, and turns off. It happens on all cycles. We have turned off the power thinking that would re-set the machine, but it has not worked. Do we need service or is there something we can do at home?


Hello &\015\012Welcome to FixYa\015\012\015\012The problem\015\012seems to be with the frozen main pump or the pump seal/impeller gone bad. To\015\012solve this the pump and motor has to be removed and then the part rep ... Asko 24 in. D3120 Dishwasher

After 3 years it just started making a loud noise, I am no expert but it sounds like a fan in a motor. I have only heard it today, but I am betting it will still happen next load too. I didn't change any of the settings, have been running the same way forever. When I did hear this noise I started pushing buttons to see if I could get it to stop, no good, no change. The cycle has completed and everything looks ok, waiting on the dishes to dry. Drainage has never been a problem for me either.


I would say this is a build up of lime.try changing your tablets and checking your salt levels.there is no fan .try what i say and see what happens.have you found a glass broken it could be as simple as that but i dont think its serious.adrian,,,, ... GE Nautilus 24" Built-in Dishwasher

Our ge profile dishwasher 6 years old does not shut off at the end of the cycle, even after 3 to 4 hours, you put your hand on the door and you can feel slight vibration if you open the door and close it , it will start what ever cycle you had it set on all over again. It cleans and dries the dishes, but I have to turn the breaker off. at the end . Paul


... GE 24 in. Profile PDW9700JII Built-In Dishwasher

Hi there, my F&P nautilius dishwasher starts the cycle as soon as I push the power button but only pumps out then swithces off. It won't let me set or change the cycle. I turned it off and left it over night and in the morning it had overflowed with water. There is no fault code showing on the display either.


When you said overflowed with water did the water come out the door the float switch in the unit may be stuck either opened or closed which if it were stuck or the switch itself were broken then the unit would have water go in and immediatley go out ... Fisher and Paykel Dishwashers

1991 model 665.1691591 shows cycle and options on display but when you push start just beeps twice and does nothing. When you push cancel/drain it shows two minutes on the display and does nothing. Tried turning off breaker to reboot...nothing.


My 665.1691591 was exhibiting EXACTLY the same symptoms. It was a bad door switch. This machine is a bit unusual in that it has 3 door micro switches.Whirlpool part number 431823 repaired my machine. It comes with illustrated directions. ... Kenmore Dishwashers

The buttons on the dishwasher won't push and let me change settings. it will only let me push start and run the last cycle ran


Try completing the last cycle till end. Check the user guide and there will be a master reset operating procedure. You may have to operate the keys in sequence as mentioned in the guide manual. ... Frigidaire Dishwashers

I have a fridgidaire dishwasher, model FDB1250REC0. When I push the "start" button, the green washing light flashes on and off, but the washer does not start. There is no cycle delay set.


... Dishwashers

Try to push normal wash, It does not lite up. Others lite but start button does not start dishwasher. I turned breaker off to re-set several times but still sme problem. Thanks Jeff


... Jenn-Air 24 in. JDB1250AWS Stainless Steel Built-in Dishwasher

My dishwasher 'start" button won't kick in. The machine seems to think it isn't locked - light wont activate, but the door IS locked. I select the cycle and option, but when i push start, it won't stay, The "clean" button keeps flashing. This is 5 years old


Hi,How many Blinks are there?Is it 7 Clean Light Blinks?Let me know, so that we could proceed.Hope i helped you.Thanks for using ' Fixya ' and have a nice day!! ... Kenmore 24 in. 17032 Built-in Dishwasher

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

Kenmore 665.15912001 DISHWASHER RUNS BUT DISPLAYS ERROR MESSAGE Instead of displaying the number of minutes in the cycle when I push the cycle selector button and then the start button, it starts as soon as I push the cycle selector, without waiting for me to push start; meanwhile, it displays "_J" instead of the number of minutes in the cycle. It washes the dishes but not well, lots of food debris. Some people in this forum have described running a diagnostic on this machine; how do you do that


... Kenmore 15912 Built-in Dishwasher

When i push the start button,it doesn't light up and start. The normal cycle and the other cycles lights work but it won't start. If i push hi-temp wash and heated dry several times, all lights will come on but when i try to run it through a cycle, it won't start.


I would replace the key pad it sounds like since everything else works.. so you hit the normal wash and start the dishwasher sits there for a min or two and turns off.. Its not recognising the start button ... Dishwashers

I have model GU3600XTSY2. Sometimes the pots and pans light flashes for no reason. Sometimes I can push that button and it stops. However, the cycle I select to wash the dishes is constantly interupted by the pots and pans (P&P) light flashing. If I push the P&P button, the wash cycle usually starts where it left off. Sometimes it will go back to the beginning of the cycle and begin all over again and get caught in a loop; start washer, P&P flashes, push P&P, begins cycle from beginning, P&


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Last month i was washing dishes in the dishwasher and if i remember correctly i opened the door to get a knife out of the dry cycle. i remembered shuting the door back and that is about it. this is my daughters dishwasher by the way. i left her house not noticing that the dishwasher ever finished. a week later she asked me if i had a problem with it. i told her no. when she goes to push the start button nothing happens. it doesn't restart its self. we have turned the breaker off and on


Hi.Depending on the model you may need to reset the dishwasher. Most Kenmore and Whirlpool built dishwashers for example need to press a reset button sequence to operate again after a problem has occurred. In that case you usually get lig ... Dishwashers

Asko D3530. Program LED does not come on. Also nothing happens when I push Set, Menu or Start. Tried button on the left (cirle with a I, looks like a reset button?). Checked plug and circuit breaker switch


Hello Rick,\015\012make sure you have tested the unit with the door closed all the way ,make sure the delay option is not turned on make sure the power cord is properly plugged into the outlet, and check your fuse box for any blown circuits sor ... Asko D3531XLHDSS Stainless Steel Built-in Dishwasher

Asko D3530. Program LED does not come on. Also nothing happens when I push Set, Menu or Start. Tried button on the left (cirle with a I, looks like a reset button?). Checked plug, GFI and circuit breaker switch. Still no power and no light no response from various buttons.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012It sounds like you've got a bad power switch or a wire at the power switch or as you described it... (circle with a I, looks like a reset button?) ... Asko 24 in. D3530FI Built-in Dishwasher

I have a Maytag dishwasher MDBS561AWW that doesn't start when the start/cancel button is pushed. Power is on. Water is on. All of the other buttons seem to function as you can cycle through all of the other settings and the lights respond.


... Maytag Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1220 seconds