Having problems with your GE 24 in. Profile PDW7800 Built-in Dishwasher ?

Press to start-nothing happens-no buttons pushed respond

\015 Everything seems normal, but push normal wash and nothing happens. ! put a gel like soap in the dispenser --does this cause any problems\015

Answers :

IN MY CASE, IT WAS THE "HEAT DRY" PAD. THE CONTROLS WERE LOCKED INADVERTANTLY. NEED TO PRESS AND HOLD FOR THREE SECONDS TO UNLOCK. I FOUND THE INSTRUCTIONS ON THE WEB.
Repair Help & Product Troubleshooting for GE 24 in. Profile PDW7800 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Press to start-nothing happens-no buttons pushed respond


IN MY CASE, IT WAS THE "HEAT DRY" PAD. THE CONTROLS WERE LOCKED INADVERTANTLY. NEED TO PRESS AND HOLD FOR THREE SECONDS TO UNLOCK. I FOUND THE INSTRUCTIONS ON THE WEB. ... GE 24 in. Profile PDW7800 Built-in Dishwasher

The dishwasher won't start, its stuck, pots/pan button is blinking, & the timer has (2)_ _ bars blinking. I tried to reset/pushed the start/resume button nothing happened. I pushed the cancel/drain button still nothing happened. I close the door tight..nothing. I check the trays if there something stuck inside..nothing. I unplug/replug the power cord nothing? my wife was using it when this got stuck about 3 weeks ago.


Did you hold the start/resume button for at least 3 seconds if this works the dishwasher will start ok but if there is a fault it will fail again best you contact your nearest service agent good luck ... Whirlpool GU2400XTP Built-in Dishwasher

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

I'm having trouble starting my ge profile dishwasher; the machine locks but then when I push the start button one of three things happen: 1) I get error C3 and I do not have a user manual) 2) nothing happens 3 I get the screen indicating that the machineis a sensing soil level, washing' but in fact nothing happens - I do not hear the motor starting and no water runs, thank you!


... GE 24 in. Profile PDW7800 Built-in Dishwasher

My Kenmore Dishwasher won't turn on. Was working fine last week, but when I went to start it yesterday, nothing starts or lights up when I push the button. The options buttons still light up, but thats it, the wash cycles and the start and stop buttons...nothing happens. I tried tripping the breaker to reset and it did no good.


Hi,\015\012\015\012A device may cease to function or operate sporadically if the electrical cord is damaged. Inspect the cord for any damage. Check whether there are any black smudges or burn marks on the outlet, cord or anywhere the cord comes ... Kenmore 15129 Built-in Dishwasher

I have a KitchenAid Model KUDP01FLBT5. After I push one of the clean buttons, and the start button and close it, nothing happens. The indicator lights for the buttons come on as you push them. When this first started, you would ahve to open and close the door and re-set the buttons (not sure if that button re-setting had anything to do with it) up to 20 or 30 times, and it would eventually come on. Now it won't anymore. Help!


Hi\015\012\015\012Thanks for using FixYa. To\015\012resolve this you will have to reset the console. Do this by closing the door\015\012and press these buttons in sequence...\015\012\015\012 ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

The clean light keeps blinking and the dishwasher will not start. I pushed the cancel button and it runs for about 30 seconds and just shuts off. Nothing happens when you push the start button.


HiIf clean light is blinking 7 times then it may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If ... KitchenAid Dishwashers

Hi. I have a Danby DDW396W countertop dishwasher brand new yesterday. We unpacked it, installed it onto taps, loaded it with dishes, and turned it on. That's where everything went wrong. When you turn it on, the display shows P2 and when you press the program button to change it, nothing happens. When you push the start button, nothing happens. What am I doing wrong? I know I'm missing something simple, but what? Please help. Katherine


Hello there and thank you for choosing fixyaThe p-2 code is a wash cycle that is the normal cycle for this unit please see below.Press the program button until the desiredprogram code appears in the display window.The ... Danby Dishwashers

My hoover hds 55m dishwasher wont start a cycle when you push the start button the led comes on but then nothing happens .


... Whirlpool Dishwashers

When I push the start button nothing happens, all the other buttons work


... Whirlpool MDBH979AWB Builtin Dishwasher

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers

I have a Quiet Partner II dishwasher. The clean button is blinking with a green light. When I try to start is over, nothing happens. When I push the cancel/drain button, I hear something happening for maybe a minute, then it reverts back to the clean button blinking and won't take any other commands. What should I try next?


... Kenmore 24 in. 16222 Built-in Dishwasher

I have a smeg free standing dishwasher model df612sdx you turn it on and it bleeps once with a green light on one of the programs. If you push the p button nothing happens along with the start button. If you turn it off and on a few times the program light moves and occassionly it will start then stop a few mins later. Any ideas. Thanks


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. This issue can be either due to a faulty door latch or\015\012door lock switch which is not engaging its ... Dishwashers

I have a 1 year old maytag dishwasher and it has the touch buttons on top of the door . When you touch the buttons to turn it on, nothing happens. It will light up the type of wash you want e.g. heavy,light...., but it won't start when pressed. It will cancel when pushed, but can't get it to start. HELP!!!


... Maytag Dishwashers

No electricity Went to use the dishwasher yesterday, but when I pushed the normal wash button nothing happened. Discovered that none of the buttons respond and no lights come on to indicate they are responding.


I would check to ensure you have power to the dishwasher and that the door is closing/secure properly.\015\012\015\012(i.e, Plugged-in properly under sink/back or washer, check for tripped circuit-breaker, and door latch ... Maytag 24 in. MDB6100A Built-in Dishwasher

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

Dishwasher is Amana ADB 2500 AWB. Door handle broke. Installed a new Latch Assy. (many buttons were pushed during process) Now .. door latches good. But when start is pushed, nothing happens. (all the cycles and options will light up) Is there a reset button? Could I have connected a wire incorrectly?


... Dishwashers

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

The power button will not work. All other buttons are lit, but when pushing the button to start the machine, nothing happens.


... Maytag MDBH985AWW 24 in. Built-in Dishwasher

I just bought this house with this dishwasher built in. I have pushed the door shut, pressed the heat dry button to lock the door and pressed the start button. Nothing happens. Now I can't even get the lights on front to turn off. The lock button flashes as though the door is open, but its not as far as I can tell. I have to press the latch in to open the door. I'd like to use it... any ideas. Its a Kenmore Elite model # 665 17052 402. Thank You


... Kenmore 24 in. 17052 / 17054 / 17059 Built-in Dishwasher

My kenmore dishwasher mod #665 17332400 isn't starting. you can press the wash selection buttons and they light up and you can push start but nothing happens - after a while it does start to do something that sounds like it wants to run then it sort of stops. Any help?


... Kenmore 24 in. 17332 / 17334 / 17339 Free-standing Dishwasher

I just went to push start on my ASKO D3232 dishwasher and nothing happened. I can turn the machine off and on but it's frozen when on. I can't change the programming and the start button just flashes and won't start.


... Asko TouchProof D3232XL Stainless Steel Built-in Dishwasher

Asko D3530. Program LED does not come on. Also nothing happens when I push Set, Menu or Start. Tried button on the left (cirle with a I, looks like a reset button?). Checked plug, GFI and circuit breaker switch. Still no power and no light no response from various buttons.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012It sounds like you've got a bad power switch or a wire at the power switch or as you described it... (circle with a I, looks like a reset button?) ... Asko 24 in. D3530FI Built-in Dishwasher

I have a kitchenaid Superba dishwasher model # KUDS011JBLO that won't start. when I push the start button all the proper lights come on but nothing happens. Any help would be appreciated.


... KitchenAid Dishwashers

Asko D3530. Program LED does not come on. Also nothing happens when I push Set, Menu or Start. Tried button on the left (cirle with a I, looks like a reset button?). Checked plug and circuit breaker switch


Hello Rick,\015\012make sure you have tested the unit with the door closed all the way ,make sure the delay option is not turned on make sure the power cord is properly plugged into the outlet, and check your fuse box for any blown circuits sor ... Asko D3531XLHDSS Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1362 seconds