Having problems with your GE 24 in. Profile PDW7800 Built-in Dishwasher ?

No water flow to dishwasher disconect the plug at flowing switch 120V no power at water valve plug


Answers :

Check to ensure you have proper volatage at the connection box behind the toe kick
\015\012 the you will need to open the door to check the door switch for both voltage and continuity
Repair Help & Product Troubleshooting for GE 24 in. Profile PDW7800 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No water flow to dishwasher disconect the plug at flowing switch 120V no power at water valve plug


Check to ensure you have proper volatage at the connection box behind the toe kick\015\012 the you will need to open the door to check the door switch for both voltage and continuity ... GE 24 in. Profile PDW7800 Built-in Dishwasher

No water flowing to dishwasher, I check the power to flow switch plug 120v no power to water valve


Check to make sure both sides of your door switch is closed as well\015\012 if your door switch is not closing properly it will not send voltage to the water vale ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Dishwasher does not start it seems there's no water coming in the tub. I got a trouble shooting manual from ejunkie.com and tested the coil of the water valve which read 1000 Ohms, which means it's OK. Then I hot wired the coil while connected to the water line and the valve opened and I had water flowing [ in a bucket] I have tried to start the test program [hold power scrub plus and regular switch at same time then start button] and lights start flashing you hear drain pump come in then the un


... Bosch SHV4803 Dishwasher

Zanussi DW908 dishwasher will not fill with water, when filled manually completes cycle untill fill time again. when filled continues on until water needed again. Only cold supply to machine. Water coming to valve, removed valve and freed it up as it was stuck, water flows through the valve when disconected from the dishwasher at filler pipe which leads up the side of washing chamber. When all connected up water will not enter the dishwasher. I,m beaten as I cannot access this area without maj


\012\012Hi,\012Here\012is a tip that will help you to find out why water will not come into\012the dishwasher... Dishwasher Trouble ... Zanussi Dishwashers

No Power I have a bosch shx33 dishwasher. I just replaced the water valve because of a leak and now I can't start the dishwasher. It's like there is no power to the unit. I know there is power because I get a shock if I touch the two wires that are connected to the water valve. Is there another trip switch or something somewhere?


First let me say that using parts of your body to test for mains electriciy is a VERY VERY bad idea. You are lucky you are not dead. Please do not touch live parts again, get a multimeter or a mains tester.\015\012\015\012If there is mains across the ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

Hotpoint HDA3400g dishwasher is not running. I have checked to make sure it has power. Took the washer apart, checked that it had power through the door switch to the timer control, all is well. Still not running or getting water into the dishwasher. Any ideas besides replacing the water inlet valve? Will this dishwasher cycle through if it does not have water?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check for the following if your dishwasher\015\012is not working-- ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens.  So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e


The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full ... Bosch 23 in. SHU 8805 Built-in Dishwasher

Whirlpool dishwasher, replaced water inlet valve and float switch and still no power to selonoid on inlet valve.


... Whirlpool Dishwashers

Dishwasher LFK-011S: First it occasionally gave four beeps (overflow) but no water in bottom or under. I then noticed that with lower water pressure machine worked ok few months. Now last week in the middle of program, drain pump started to run, machine gave four beeps and pump kept running even main switch off. Now when I plug in power cord, the pump starts to run immediatelly


... Fagor LFA013 SS 23 in Builtin Dishwasher

Zanussi zsf6126 dishwasher showing fault 3, water inlet not opening, not receiving power to valve. tracing circuit without diagram have tested both level switches and valve but no fault found there. can you help please?


... Zanussi Dishwashers

I have a zanussi ZSF2440 dishwasher, when it turned on by the power button on the front you can choose a cycle and start it, Once the cycle is started it fills up with water but doesn't stop until it over flows setting off the flood protection, which cuts the power, so all the lights on the display go off and stops the water flow and drains the dishwasher and keeps draining the dish washer while the flood protection is on. It seems as if the dishwasher doesn't know when its reached its correct


... Zanussi Dishwashers

I have a JennAire jdb1090aws dishwasher. It's about 4 years old. The symptom is no water flowing through dishwasher. Approx 3 months after installation, the same symptom occurred. Tech resolved with float switch adjustment (no charge). Has run fine every since. I have not checked water supply, but doubt this is the problem (new water heater 3 months ago, sediment gone). I suspect the float switch is bad or out of adjustment. How do I trouble shoot float switch in dishwasher? Connect ohm mete


Hi,The procedure to test the float switch :-http://www.partselect.com/dishwasher+test-float-switch+repair.htmMost for no water entering the dishwasher, there are 2 main causes. One is the float switch and the other ... Jenn-Air 24 in. JDB1100AW Built-in Dishwasher

Dishwasher confused Dishwasher was switched off just after cycle commenced (tablet had been released). On restarting dishwasher, it wouldn't take in water and has just been going through the motions of the cycle without anything happening. Even when the power button on the machine is switched off or the door is opened, the motor continues to run but without water. Water is definitely switched on under sink. I think the computer is confused - can you please help?


I suspect this is nothing to do with switching off during the cycle.take the bottom plate off and check if there is water leaked into the bottom pan. alternatively, if you can, tilt the machine back to 45deg and see if water runs out.most ... Dishwashers

Water won't drain from bottom of dishwasher. I pulled the dishwasher out, blew through the drain tube, disconnected the drain tube and felt around inside. Ok there. The dishwasher has not been in use for 4 months, due to low hot water flow. I replaced a clogged valve today and restored water flow, and I'm wondering if non-use causes a problem with dishwashers?


Sorry to hear that you are having problems with your DW.Actually, yes. Not using a dishwasher for a while can damage some parts. Sediment from water damages the water valve. Food residues clogs the drain and drain pump. More likely the ... Dishwashers

I have a Maytag dishwasher and the power is not getting to water valve(solenoid) it comes straight from timer(pin 29) solenoid works with 120v applied


Check you float,is it stuck up it should lift and drop freely. if thats ok and the wires are fine your timer is probably bad. ... Dishwashers

Model FDB4315LFC2 Serial TH80658596 It is only 20 months old but Does not load with water. I have checked water line into white valve and water is flowing, but it does not come into the dishwasher. If I manually put water in the bottom of the dishwasher it works fine through the cycle until it is time to pump in more water. There is a sound but no water comes through the valve.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. As you have already checked the water line for clogs/obstructions and the water is flowing but wont fill ... Frigidaire Dishwashers

My power button cover broke on the dishwasher and I figured out the part number I needed, but when I put it back together I got the wires crossed on the board and door switch. Now the control lights up , but the dishwasher will not run a cycle. THe question is does the plug on the door switch have to be a certain way, because there are three wires and you can connect the plug both ways. I did turn the plug, but it still does not run. Did I break the switch? Bosch SHU9956uc/14


The wires do have to be a certain way on the door. Otherwise a door open can tell the board that's it shut and vice versa. The easiest way to do it, is test the switch with an ohmmeter, place the meter on the switch, push button in and see if the rea ... Bosch SHU9956 Built-in Dishwasher

My dishwasher was recently 'installed'. i don't know if the contractor made a mistake or if the water valve is not turned on, but the cycle tries to start but then no water is flowing into the dishwasher. everything appears to be hooked up, but I think it's the water issue b/c i also have a new refrigerator and the water dispenser/ice maker does not work because no water is flowing into the fridge either.


This sure sounds like a water valve issue, for sure. You will have to trace out the lines (not easy, but possible) and figure out where the valve is. They usually turn left to open, and right to close. I would call the contractor and tell them ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

I have a DU8000XX6 series Kenmore dishwasher that won't drain the water properly. There is about a half inch of water in the tub and the float is raised (not sitting on tub bottom). When I lift up the float a little more I can hear the float switch make. I would assume that when the water is high enough the float switch makes and energizes a solenoid valve in the drain to drain the water, but shouldn't it stay open until all the water drains? Lifting the float while the dishwasher is off wo


... Kenmore 24 in. 15142 Built-in Dishwasher

I have a McCulloch FHH18A power washer. When plug it in without the water turned on, the pump will start. As soon as I turn the water on to the unit, the GFCI power cord trips. Water does flow through the unit as I have water at the wand nozzle when not plugged in. Any suggestions?


I would guess there is a leak somewhere inside the unit that is spraying water on some electrical component and causing a ground fault. ... McCulloch FHH18A Electric Pressure Washer

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers

I have a Neff Dishwasher and I think the problem is due to the cold water inlet valve. When the dishwasher starts it drains any water and then should stat to fill. If I monitor the voltage to the valve it does switch to 240V but still fails to fill. I have verified that the cold supply works OK and the filter on the inlet is clean. The dishwasher is a NEFF GB5121 and is about 20 Years old.


... Dishwashers

I have error E:15 with a flashing water tap sign - I've tried the following: a) Clean filter at the bottom - now flushes out with b) remove power - return power c) remove and clean fiter for incoming water at a sort of valve Nothing! when I attach power it continues to flush out (even without water) if I put water in it evacuates without problems. The tap does supply water I've check and with more than sufficent flow and pressure! ...Help .....Thanks Gary


Hello Gary,\015\012\015\012You didn't specify the brand or model number of the dishwasher, but I suspect it's a Bosch, in which case the E:15 error with the flashing tap sign and the drain pump running continuously means the anti-flood pr ... Dishwashers

Our bosch dishwasher runs but no water is spraying on the inside. Is there a water filter clean out or is there a water pump that might be broken? I checked the line coming in and it isn't plugged. I made sure where the stainless line goes into the electric valve that it wasn't plugged to that point. I could see anywhere else to check if it was plugged. I figure there has to be a water pump, but I guess I'm not sure of that either. Thanks for any help..


Hi, welcome to Fixya. \015\012 \015\012By the description you've provided, it sound's like the wash motor is either seized or just stuck, let's hope it's the later. \015\012 \015\012Bosch had issued a service tip about this ... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2958 seconds