Having problems with your GE 24 in. Profile PDW7800 Built-in Dishwasher ?

GE Externa Tritan XL (7 yrs old): Standing dirty water

\015 GE Externa Tritan XL (7 yrs old): The dirty water is standing in bottom after cycled. What do I do before I call for repair person?\015

Answers :

Hello, there isnt much that you can do, there could be a number of problems. It could be a slight blockage somewhere from your drainage hoses to your pump. It could also not be spinning properly. If you want to drain the rest of the water out you will need to get your drainage hose and lay it flat on the floor to a drain, this will stop things getting smelly. You just may have to get a repair man in, I hope this helps.
Repair Help & Product Troubleshooting for GE 24 in. Profile PDW7800 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

GE Externa Tritan XL (7 yrs old): Standing dirty water


Hello, there isnt much that you can do, there could be a number of problems. It could be a slight blockage somewhere from your drainage hoses to your pump. It could also not be spinning properly. If you want to drain the rest of the water out you wil ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Whirlpool Dishwasher GU2548XTP- Dishes still dirty after it has run, especially the top rack. 5 (?) yrs old. Runs and grinds intermittently, no water seen under unit. Sometimes I add more water when it grinds, then it runs very quiet. Sometimes it doesn't seem to fill enough. Water supply good, inlet screen inspected not clogged. Not a lot of pressure shooting the water around the inside of the unit, as the detergent that bleeds through the slotted half of the detergent flip door isn't r


The inlet valve is OK, therefore the control board was not the problem. The impeller pump is noisy and inefficient, and must be replaced.Here is the part: ... Dishwashers

I have a Kenmore, Stock 15649, approximately 14 - 15 yrs old that worked fine until the past few days. The upper rack doesn't appear to be getting any water, as bowls and glasses are still dirty after being washed. It appears as though water would spray from the bottom, through a "nozzle" in the middle of the lower rack, then go to an arm located underneath the upper rack. I haven't noticed any obstructions in this path that would inhibit the water from spraying. Any suggestions (outsid


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Dirty dishes The dishwasher in the house I moved into is a very basic model of approximately 1-2 yrs. old. In every load that I wash there are some dishes that are not cleaned properly. I do not have access to a users manual and was wondering if I need to set the water temperature? Can anyone help?


You need to take the spray arm off of the bottom and get down to the filter: there's probably food trapped in the filter somewhere, not able to drain out and it keeps recycling onto the dishes at each cycle. Good luck! ... Sears 24 in. 14181 Built-in Dishwasher

I have a ADG450 about 7 years old, the problem is there is dirty water left at the bottom of the dishwasher after finishing the cycle and the dishes look as if they have had the final rinse in the dirty water. also i have tried the rinse cycle with no dishes and all the rinse water had not drained away. I have cleaned the iside of the washer and where the water goes to the pump. Any ideas


Check the pipe leading from the dishwasher to the outlet, maybe under sink. this needs to be raise up as water will flow back into washer. Had this problem myself, felt foolish when the repair man just tied it up and left. ! ... Whirlpool ADG450 Slim-Line Built-in Dishwasher

I have a 13 month old (Thanks Sears warranty!) Kenmore Portable Dishwasher Model 665.17769. It drains poorly, taking 2-3 times after load is completed running thru the ''cancel/drain'' cycle to clean it out. It is not getting dishes clean either, presumambly because the dirty water isn't being flushed out at cycle end and instead of rinsing with fresh water, it's still screwing with the dirty water. Manual doesn't offer any advice except to see if the hose is kinked (it isn't). I made sure nothi


Hello Linda it sounds like you may have a piece of glass or some other hard material in your drain pump which is partially blocking the draining process. Remove the hose in the base of the machine, then unscrew the drain pump and physically examine ... Kenmore Dishwashers

My dishwasher after the cycle is over still have a bit of dirty water remaining on the bottom. After few hours is getting more and more dirty water. I have a feeling that some kind of the valve is not working correctly which allows the water from the sink drain to come back? Am I right? Is it a big re[pair or marginal? My dishwasher is about 20 + years old and still the greates one I owned ( I had before Bosh ). I own the dishwaser for last 4 years but previous owner loved it and never repair


Hello Ma'am/Sir,\012 The Best thing you're going to do is to have new Dishwasher.A lot of brand new products can help you, rather than striving the old one...Hope it will help you! God Bless you...Thank you! ... Miele Dishwashers

Water wont drain out of bottom of tub. The dishwasher works fine, it just wont drain the dirty water out. If I restart it to wash again, the dishes are washed in the dirty water.


Hi, A clog in the drain line or air gap (if there is one) is the usual reason that a dishwasher won't drain. Often the problem is at the point where the drain line attaches to the garbage disposer or househ ... GE Nautilus 24" Built-in Dishwasher

Dishes and the dishwasher look dirty after they run, like it redistributed dirty water. The door is very dirty/filmy except right under the soap dispenser, like someone squirted dirty water on it but wiped right under the soap dispenser. If I run it a second time with vinegar it gets clean, but that is crazy, esp since it takes 2 1/2 hours a load. I have 2 of them and both are doing it. I have changed soaps, added more soap, used less soap, pre-rinsed dishes, put them in filthy, used jet-dry, no


Hi Mike_wend604,\015\012\015\012I am looking for a used Asko #1504, if you would like to sell yours please e-mail me at [email protected] and put "Asko" in the ... Dishwashers

Kenmore dishwasher Food particles left on dishes and inside of dishwasher. All functions appear to be working normally. Water pressure OK, drain OK, water temp OK, Etc. Operating dishwasher though a normal cycle without dishes solves the problem for one load, then back to problem. Dishwasher is about 5 yrs old and worked perfectly for 4 yrs. Any advice would be greatly appreciated. Bruce


... Kenmore 17822 Free-standing Dishwasher

Kenmore Dishwasher doesn't rinse? It sounds to be working fine, however, at end of cycle, dishes are still dirty, and the front door on the inside is still dirty. Obviously there is a problem here maybe with water pressure or something. There is steam at end of cycle, can't tell about water other than that.


Try opening the dishwasher during the wash cycle stop it and open it if water is in the bottom it is filling whn you open do 1 or 2 times to check to see if spry arms are spinning if they are check to see if soap dispenser is working also use dishwas ... Kenmore Dishwashers

Our dishwasher beeps twice when the start button is pressed but then doesn't do anything and there is no other noise from anywhere (eg, motor/pump). There are no error codes displayed and the display appears normal (ie lights up and shows time for program completion etc). When the problem first occurred the machine was full of dirty water. We have turned the dishwasher off and on at the wall, checked/cleaned all filters, drained the dirty water and still nothing happens (it doesn't even fill


... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

My dishes are not getting clean. There is dirt and residue on glasses and other dishes. I have checked and nothing seems to be clogged, but I'm not sure I checked everything. The inside edges have a build up of dirt and residue, like the water is dirty or the dirty water is not draining. What should I do.


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher

Dishes on top rack on not getting clean on the outside e.g. the outside of an inverted cup is dirty and dirty water is collecting in depressions. There doesn't seem to be a mechanism to rinse the dishes from the top. Also water not hot on any cycle so probably need a heating element. Where can I purchase one near 85204 zip code


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Ariston Technologies L63SNA Stainless Steel Built-in Dishwasher

Zanussi Dishwasher DW 915. At the end of the cycle, some dirty nasty smelling water is left at the bottom , and some dirty water is left on the underneaths of the glasses and cups. Have you a solution?


Hi,\012Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... Zanussi Dishwashers

Frigidaire Dishwasher Model #FDB1500LFS2 After finishing all cycles, no problems at all. But if it was not in use for couple days some dirty water back up at the bottom. Then just let the machine run and wash another full cycle, everything is fine, but couple days of no using , dirty water back up again


... Frigidaire Dishwashers

Asko diswasher Dishwasher will not get water. Lines all checked, water on. Pump runs even when in off. Problem started when there was a water clog in the sink next to the dishwasher, and the dishwasher backfilled with water. We used a shop vac to get the dirty water out. Next day tried to use dishwasher, runs, but no water and empying pump will not stop running. Ideas?


Check for water leaks or not draining/overfilling fault ... Asko D1776 Stainless Steel Built-in Dishwasher

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

Dishwasher I have a whirlpool dishwasher that does not appear to be getting hot water. The washer water is cold initially and only seems to get warm once the heater in the base of the machine heats it. The hot water supply line does not get hot so I presume no water is being supplied. Is the water supposed to be hot at the start. If yes could this be caused be a faulty inlet valve and if so how can I check. The dishes are dirty especially on the top rack. Thanks for your help. David


Gendos is on track with his question. I have the same dishwasher and it doesn't get enough hot water to clean the dishes and runs for hours because the heating element wasn't designed to heat water, just maintain it. The only solution we have found ... Whirlpool GU2400XTP Built-in Dishwasher

Bosch Classixx dishwasher: Initially no water feed and 'water check' light came on. Removed side panel, emptied water from base. Ran OK for a week or so. The problem then repeated so side panel removed, float switch operation checked (OK) drained water from sump below polystyrene float. Ran OK but contents came out dirty and cold - no heat. Side panels off again, water in base but no obvious leak when watched during cycle - still no heat. Help please.


Http://www.repairclinic.com/Dishwasher-Repair-Help\015\012\015\012\015\012\015\012 ... Dishwashers

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

My 12 yr old KitchenAid -Sculptura-Model KUDR24SE starts to fills with water and then does nothing else. It will eventually go through the cycles on the panel, but nothing is happening inside. End result is still dirty dishes with water sitting in the bottom that has to be baled out. Cups on top rack don't have any water on the indentations, so it's obvious that the thing filled with water and that's it. I had the motor replaced (supposedly with a new) one 2 years ago so I find it hard to bel


... Dishwashers

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

Leaking from underneath. Water appears from under basboard to the right of dishwasher, not from directly in front. Only seems to leak during rinse cycle and has just started recently. Removed front panels and noticed the bottom of cabinets on both sides have water damage as if water has been leaking for some time. Never have seen any water until now. GE model GSD500X-66WB. Came with house, approx. 15 yrs old.[


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101\012\012\012,fhjsuj ... GE 24 in. GSD500X Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0886 seconds