Having problems with your GE 24 in. Profile PDW7880G Built-in Dishwasher ?

My GE PDW7880G doesn't clean items in the top rack. The dishes on the bottom seem fine. I do make sure to push the top rack all the way back so it engages.


Answers :

Removed the sprayer. the part that spins under the top rack and check that the holes arent clogged.
Repair Help & Product Troubleshooting for GE 24 in. Profile PDW7880G Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My GE PDW7880G doesn't clean items in the top rack. The dishes on the bottom seem fine. I do make sure to push the top rack all the way back so it engages.


Removed the sprayer. the part that spins under the top rack and check that the holes arent clogged. ... GE 24 in. Profile PDW7880G Built-in Dishwasher

I need the diagram for the door pulley system so I can make sure I am hooking it up right. The original door chord/pulley assembly broke. I ordered new parts, Now I want to make sure I am putting it back together the right way. The edge of the screw- on floor panel is pushing the plastic hook off of the door hook when you shut the dishwasher door.


... KitchenAid Dishwashers

Frigidaire dishwasher doesn't seem to wash top rack. The dishes are oily with stuff dried on them. It worked for several years before this. I took out the sprayer and ran water thru it to make sure it wasn't clogged. No luck. It almost seems that no water is running thru the top sprayer.


Have you taken the tube that goes to the top sprayer off and washed that out as it may be clogged especially where the sprayer goes on it has a small opening. ... Frigidaire Dishwashers

Our top rack is not getting cleaned at all-- although the rinser seems to spin freely when pushed, and fits correctly into the hole back. We were using powder detergent, and a little residue was always left in the compartment. So we tried liquid detergent, to see if it would help, and now it seems like almost none of the detergent is dissolving out, at all. The compartment's full and a goopy mess after each cycle. So now the bottom rack isn't very clean, either! Please advise. Thanks!


Welcome to FixYa,Based on your description... I`d suspect a plugged or really dirty wash pump. It could ultimately be a worn out wash impeller/chopper assembly, but I'd certainly try my suggestions before considering that. ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have an kenmore elite "ultra wash" model 665. not sure the rest.. about 7/8 years old, making loud buzzing sound during wash cycles,starts about 5 minutes into the normal wash cycle. i removed the inlet protector and the chopper area and all was clear.clean...it's running now and seems to be pumping the water, but can live with this buzzing noise,,, any idea, is the pump on it's way out ? just stopped as it kicked into another cycle, at 42 minutes...but it will be back, any ideas ? (back alrea


Buzzing sound may be coming from a solenoid that is mounted under the dishwasher, below the tub ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have an electronic operating Kitcheaid Dishwasher. It has a tendency to stop in the middle of a cycle without warning. This can happen at different times of the day and at different stages of washing. We open the door, make sure the racks are pushed in tight and close and hold the door tight for a few moments. The dishwaser comes back on, but this can repeat in the course of one wash.


I would try adjusting the strike which is a little metal piece coming off of the tub that goes into the door when you close it. the strike may not me latching properly ... Dishwashers

The top rack dishes are not being cleaned properly. It seems that the water is not makeing it way throught the feed arm, hence not being feeding the spray arm.


Hi Please check if something is blocked near the top spray arm, also make sure that all holes are open. Use a sharp metal pin to clean the holes on the top spray arm. Make sure the water pressure i ... Dishwashers

Pump doesnt seem powerfull enough to push water to top rack. i have cleened the filters and checked the pipe to the top rack and there are no obstructions. It is filling with water fine and empting with out problems(emptying seems slow) any ideas?


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Kenmore Dishwashers

My Kitchen Aid KUDS01DJSS0 seems to have water going to the upper spray arm (I see water coming out of the unit just beneath the upper rack), but the pressure doesn't seem to be high enough to clean the upper rack. No evidence that water is coming out of the spray arm on the very top. Lower rack dishes seem to clean OK. I have already removed the whole upper spray arm assembly and inspected the flapper valves that the middle sprayer goes into. I suspect that it's not making good enough contac


... KitchenAid Dishwashers

The top rack of our Asko dishwasher spontaneously slides forward when we open the door and pull out the bottom rack. I can't get it to catch and stay back. This seems to happen regardless of whether the top rack has items on it or not.


... Asko 1385 Dishwasher

I am not happy with the racks in my new Bosch dishwasher! The bottom rack is not right! The silverware basket is in the back right corner and the silverware catches on the seal on door and it is hard to get to. The tongs are two close together and point the wrong way? The upper rack's tongs are also to close together also. I don't seem to be able to get larger dishes in with these tongs in the way. Having never used the mdl 9000359119 Rev B I had no idea. Buying a Bosch ment quality to me


... Bosch Dishwashers

I have a maytag MDB600AWW dishwasher. the top spray arm doesn't turn. it wouldn't even turn if i removed the to middle trays. I took the accumulator out and cleaned it. the fine mesh filters were clogged. unfortunately, birthday candles found their way into the machine sometime back. i cleared as much as i could. when i put it back together, the top arm would spin only when i had the 2 middle arms disconnected. It seemed there was an increase in pressure. i ran a diagnostics test and there were


First check to see if the washarm itself is clogged, if so clean it out.\015\012\015\012If the arm has a bearing it may be shot.\015\012\015\012You may have a clogged manifold on the output side of the pump. I sometimes run a ... Dishwashers

The unit goes through its cycles but the top rack is not getting clean. The bottom spray wheel works, the middle and top spray arms are getting water but it seems not enough to make them rotate. The pump screens are clear and there seems to be enough water. Whats going on?


The problem is likely to be that the jets in the rotor arm are blocked.\012\012To check this, remove the arm (it is easy to do, as it is intended for the user to do this) and clean out all the holes. Try running water from you tap through ... Dishwashers

I can't put back the top dishwasher rack. The railing does not seem to hold it, even though there is no damage in the railing. The top rack could not be held by the rollers


There should be plastic stops at either end of the rail that prevent the rollers of the rack from coming out of either end. ... Maytag Dishwashers

Bosch Dishwasher I have a stainless steel Bosch dishwasher, I made the "mistake" to try to see if I could fix the jammed handle from the door. Unfortunately, (did not realize the top panel comes off without opening the entire door). I removed the screws from the door frame (Inside panel), and the door springs/latched got loose. I would like to put it back together, but I dont have any diagrams on the door to make sure all parts are in place to put the door back together. I have been havin


Hi ED,\015\012\015\012It sounds like a real problem here. If the springs are still in one piece, my best guess is to to remove the springs from the door. Then attach the springs to the dishwasher body first, then reattach the spring to the door. Not ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

The dishes wont come clean on top rack? the bottom rack is clean..we tried cleaning filter and making sure the wash arm wasnt hitting anything..we tried different wash settings..please help Jessie Oakes


Check that the top rotating arm jets are not block. These often get blocked by pieces of food or other solid particles, this is the normal problem. ... Whirlpool DU1055XTS Built-in Dishwasher

Top spinner does not seem to be getting water to make it turn top rack dont clean


Hi,\015\012Before going to a lot of trouble, I would recommend replacing the top spinner...\015\012On my dishwasher I had the same problem and found that the spinner was not working because of mineral buildup inside and wear... change the ... Kenmore Dishwashers

Food particles are left in the dishes on the top rack of the dishwasher. I have checked for debris clogging the spray arm but there isn't any. I have to wash my glasses on bottom rack to make sure they are clean.


Is this a bosch dishwasher? if so then check my recent post about that here.http://www.fixya.com/support/t1713479-bosch_dishwasher_top_ ... Dishwashers

It always seems like it never gets enough water to even make the spray arms work. I have even tried to make sure I am not running any hot water in the house. It is about 7 months old and has always acted this way. Could there be something wrong with the installation? My old Sears never had this problem.


Sounds to me as if there is a blockage in the water line supplying the dishwasher or a kink in the water line supplying the unit. Since the water is supplied from the angle stop under the sink there could be blockage at that point. What I would sug ... Dishwashers

I have a Frigidaire dishwasher and there is not any water coming out of the top wash arm. There is good water pressure coming out of the lower washarm. I pulled out the dishwasher and can see the water going to the top washarm through the tube and it goes up very slowly. I took out the "check ball" below the lower washarm and it worked good. I put the "check ball" back in and ran the machine on "Upper Rack" and it still does not have any water coming out of the upper washarm. It doesn't seem lik


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check that there is no gunk or mold\015\012behind the filter screen and under the cover at the bottom. N ... Frigidaire PLDB998A Built-in Dishwasher

The top rack on my dishwasher won't stay back like it did when it was new. It keeps slidding out making loading the bottom rack difficult. Can I replace the wheels or something else?


... Maytag MDBH985AWB / MDBH985AWS 24 in. Built-in Dishwasher

The bottom rack of the dishwasher is always coming off the "track" or what passes for one. The wheels seem too small or the rack isn't wide enough Makes it very diificult to push in or pull out.


Hi\015\012Problems with the dish racks usually occur because the racks have been jammed back into the tub housing after they're fully loaded. Careless handling can exert enough force to crack or break the roller wheels or throw the racks off th ... LG Dishwashers

Our 16 year old dishwasher takes way longer to finish cycles, has become very loud and now no longer cleans the dishes - especially the top rack and the silverware. We have hard water and I have run it with vinegar in a bowl 3 times and have been cleaning all the deposits I can today. It doesn't seem to be draining out all the gunk. Water flow seems ok, the arms have nothing blocking them. Any instructions for me to follow to clean out the mechanisms? Or has it run its lifespan... Thanks!


Parts are no longer available for your dishwasher. Typically - manufactures end support after 10 years.Your hard water deposits will never come all the way out. They will be "clean" for a month or so until another calcium chunk breaks free and ... Dishwashers

My kenmore dishwasher, model 665.16473300 has stopped working. Now the lights just flash at the Smart Wash, Normal Wash, and Cancel. I've reset the power and it just comes back. I've taken the drain area apart and made sure there are no obstructions. The buttons seem to respond, as after I reset the unit (breaker), only the Smartwash button is flashing. I push cancel and then it starts flashing. So I think the buttons work, but it's locked up.


IS THE WATER TURNED ON TO THE DISHWASHER ... Dishwashers

Fisher Paykel Double Drawer DD601v2. Half way thru a cycle the alarm went on both drawers even though the top one was not inuse or switched on. The error on both drawers is F1. If we push the power button on both after a few seconds they both start up making a whirring noise and both drawers flashing. We have to unplug the machine to stop the irritation. What is wrong and how can we mere mortals fix it ?


Hi,The F1 error means that the sensor that is located in the pan at the bottom of the machine has sensed water.It does not want either machine to run with a leak so it will shut down the operation of both drawers. ... Fisher and Paykel Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0967 seconds