Having problems with your GE 24 in. Profile PDW8280JSS Built-in Dishwasher ?

My 3-yr old GE Profile dishwasher lost power soon after initiating wash cycle. Checked braker switch...fine. Checked outlet power...fine. Dishwasher power mysteriously came back on approximately 12 hours later. Initiated another wash cycle and lost power again after a few minutes. Water remains in bottom of tub. What's wrong????


Answers :

First thing i would check is the actual wiring behind the toes kick
\015\012you will seea wire box, shut the breaker off, open up the box and double check all your connections there,
\015\012 the next step would be to check the voltage across the door switch
\015\012if your comfortable with opening the door panal
\015\012 since the door will be open you should have voltage across the switch
\015\012 worst case senerio, your board is lost in the logic
Repair Help & Product Troubleshooting for GE 24 in. Profile PDW8280JSS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My 3-yr old GE Profile dishwasher lost power soon after initiating wash cycle. Checked braker switch...fine. Checked outlet power...fine. Dishwasher power mysteriously came back on approximately 12 hours later. Initiated another wash cycle and lost power again after a few minutes. Water remains in bottom of tub. What's wrong????


First thing i would check is the actual wiring behind the toes kick\015\012you will seea wire box, shut the breaker off, open up the box and double check all your connections there,\015\012 the next step would be to check the voltage ac ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

Frigidaire FDB126RBS2 Washer stopped working mid-cycle. Then a few hours later began washing again. Ran a load a day for another week before it happened again. It ran and stopped at Light Wash, then a few hours later started again and stopped mid-way through the rinse cycle. It has no power now and will not start again.


Be very careful, it sounds like an electrical failure, were the machine has cut out to protect you and itself. You need an expert there and quickly. Water and electric are a bad mix and more house fires are caused by washers than most other appliance ... Dishwashers

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

Have a GE Quiet Power 3 Dishwasher. Went to reun it and when I closed the door no lights came on to pick a wash cycle. Nothing like it lost power. No buttons work, nothing. Opened door and removed inside door panel. Have power at door latch switch. Actually have power at all 4 connections and doesn't change when engaging switch as if door was closed. Switch does click but no power at front control panel. Whats up. I have my own Handyman/Home Remodeling business and I'm very good at fixing things


If your dishwasher is not running check the following \015\012\015\012You have already taken care of the 1st item.Power Supply The main power supply is the first thing to check. Also remove the toe ki ... Dishwashers

My 2008 frigidaire 24" dishwasher model #FDB1050REC is not washing during the cycle. I have run the test cycle and the tub is filling up and draining but no washing is taking place during the wash cycle. The dishwasher has an electronic control board and therfore no mechanical timer. I put test leads to check for voltage on the power leads to the main washing pump, which I have already replaced with a new one, and I'm only registering a low voltage of around 10 or 11 VAC. With the cycle off I'm


If you have replace the motor and this did not fix your problem then yes replace the control board ... Dishwashers

My dishwasher skips the final drain cycle. The lines are all clean and there is no clog. It drains just fine in the beginning of the wash cycle. Every time I do a load of dishes I have to run the full cycle, then leave the machine open for 3-4 hours and start the cycle again and listen for the drain at the beginning of the wash to drain the machine from the initial wash and stop the machine after it is done draining so it won't fill up again. Sometimes we have to unplug it and wait about an hour


... GE Nautilus 24" Built-in Dishwasher

Dishwasher I have had above integrated dishwasher which is intermittently tripping the mains fuse. Power is getting to dishwasher and the washing cycles work until a certain point (not the same time) where a loud bang can be heard and the main fuse is tripped. Reset the main fuse and power still gets to the dishwasher and it works again. It has just started to trip the fuse when its not running any cycle (just when power is getting to it). I've checked the fuse on the spur and it looks ok. I hav


Its quite common for the interferance filter to fail on these models its situated in the base of the dishwasher connected to the mains block usually when they fail you can see black dust around it, ... Neff 24 in. S5456 Built-in Dishwasher

We have a Bosch dishwasher SHX46A06 UC/21. It continually runs. We couldn't find a diagnostic test for our model, but we did for another model. We held down the power scrub and regular wash cycles then turned it on and pressed them again. The delicate/econo light started blinking. Looking at some of the blogs, most often it seems to be the heater or the control panel - does this diagnostic test help to pinpoint what could be wrong? Also, where can we find a good manual for our model - we're havi


Here is a link to the service manual http://cgi.ebay.com/Bosch-Dishwasher-Service-Repair-Manual-/250480379703. \015\012 ... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

The dishwasher pump sounds like it is trying to drain, even when the stop button is pressed and the door is opened. The only thing that stops it is turning the power off at the power point. However, when the power is turned on the pump continues. The wash cycle icon flashes, but the usual cycle indicator is not lit at all. The dishwasher will not commence a new cycle.


... Asko D3122XLW / D3122XLB Dishwasher

I have a Fisher & Paykel 913T soft touch dishwasher. On all types of washes when the wash cycle starts there is no 230 volts on the element & after 5 minutes the wash cycle finishes & then goes onto to the next cycle. None of the wash or rinse cycles heat the water but on the dry cycle their is 230 volts onto the element & dries the dishes OK. Is my problem the power supply PCB or could it be the Controller PCB? Does the 230 volts to the element on dry cycle come from the same cicuit on the po


Have you considered the possibility the water temperature sensor may be faulty.\015\012\015\012If the controller is getting false water temp reading then it may never turn the heater on.\015\012\015\012Generally with FP dishwa ... Dishwashers

On my Kenmore Ultra Wash Dishwasher model 665 the Normal Wash light is blinking even though the previous cycle finished successfully. Also I can't start the dishwasher -- it doesn't respond to any of the buttons. I have powered it off and on and the Normal Wash light comes back on within 5 seconds of restoring power.


Http://appliancejunk.com/forums/index.php?topic=2933.0\015\012\015\012\015\012\015\012Hi. please find above your service and repair manual, bel ... Dishwashers

Dishwasher runs for appx 14 min & stops washing half way thru wash cycle. Timer contunies to run. No drain pump out (nothing). Let dishwasher set idle for appx 1 hour and it will re-set. Set timer forward to end of wash cycle and it will complete rinse and final rinse. Then go to dry. Timer works ok.


This sounds like something is stuck in the drain pump. You can remove the inner cover to look for obstructions. You have a dual purpose motor it does the both circulating and draining. The blockage is causing it to overheat and trip the thermal prote ... Whirlpool DU840CWD Dishwasher

KENMORE DISHWASHER STUCK IN WASH CYCLE it will not move off of this postion water heats up it cleans but does not move off this cycle. New 2008 Kenmore 1610 built-in dishwasher won't leeave wash cycle. repair person says it is supposed to take 3 hours.


... Dishwashers

We had a power cut. When it was over the dishwasher continued and finished its wash cycle. The lights on the control panel, on/off and wash cycle indicator lights did not work during the remaining part of the cycle and will not work now. The dishwasher is a Hotpoint, mod. LFT 114 UK


... Hotpoint Dishwashers

Frigidaire FDB520RHB Dishwashers : We bought this dishwasher about 3 months ago. Today I ran the washer before I left to do errands and when I returned, I believe the washer had finished its cycle. But about an hour later, I noticed it had started up on its own? It then proceeded to run for almost 3 hours before my husband canceled the cycle. We were kind of waiting to see if it would stop on its own, which is why we let it go so long. I think it usually takes about 1 1/2-2 hours to wash. Could


Try to run the dishwasher on a short cycle like rinse and see if it finishes the cycle.It is likely the heater or hot water temperature is not reaching the desired level and this could cause the extended wash cycle. Feel water temperature ins ... Dishwashers

My dishwasher shut off in the middle of a wash cycle and has no power and the breaker in the panel is on


... Maytag Dishwashers

Wash cycle, the pump cycles on and off does not continuously wash. The wash cycle will not complete and then the dishwasher turns off. I can restart another cycle immediately with the same result with varying run times.


... Maytag MDBH965AWS Stainless Steel Built-in Dishwasher

Frigidaire dishwasher won't end cycle - will run on and on for hours. Sometimes it cycles through, usually it just endlessly washes and rinses. I have to CANCEL the cycle, which causes the dishwasher to empty and run a few RINSE ONLY cycles (which are consistent, cycle time wise) to rinse the soap off of the dishes. Also, the door for the soap seems to stick - how long into the cycle before the soap door should open? Also, does opening the washer during it's cycle (to add more dishes) change or


I would say the resettable thermostat has failed. There is a thermostat which senses the water temperature, and when it fails, it causes the dishwasher to run constant. Replace the thermostat underneath the dishwasher and that should cure problem. P ... Frigidaire 24 in. FDBB540 Built-in Dishwasher

I have a Frigidaire Series PLD2855RFC3 dishwasher. Near the end of the cycle the dishwasher stops and begins flashing "PF" on the display and the lights for "Hi Temp. Wash" and "No Heat Dry" also flash. I know "PF" = Power Failure, but the power never goes out... so what is causing this error and disruption in the cycle?


... Dishwashers

KUDS30IXSS1 dishwasher will pump out water completely on the one hour wash cycle, leaves water in tank at end of all other cycles. Will completely drain when cancel/drain cycle is pushed. Is there a re-set code, or sequence; or is there a diagnostic code or sequence tohelp me? Like push Heat/dry, then normal wash, then Heat/dry, then normal wash within 6 or 7 secs? Or is my circuit board just shot?


... Dishwashers

I have a Sears Kenmore Elite Ultra dishwasher 665.1315 model. For the last 3 weeks, it keeps having the clean light blinking 6 times pause then 1 blink and pause and repeats cycle again. I have turned off the breaker...I have reset by pressing the heated dry and normal wash until all lights are flashing. It then completes some type of cycle and looks ok. When I opened the door, steam came out and all was hot inside. However, once I try any new wash cycle, it seems to wash but after 1-2 hours and


Call sears service and tell them you need service there is a service flash and will be no charge ... Kenmore 24 in. 15932 Built-in Dishwasher

My dishwasher stop working in the middle of washing cycle. The water has not drained out completely. I attempted to restart the dishwasher but it appears there is no power. I checked the power auto swithch/fuze on the master fuze board. There is still no power going through the dishwasher.


... Dishwashers

I have no power to the dishwasher. I tried the circuit breaker, flipped it. No lights on, nothing. It must have been running when the power might have gone off, may be the power surged or something and it wasn't able to finish running the cycle. I have taken out all my dishes and washed them by hand but I still have water standing in the bottom of the dishwasher. I am a mechanically challenged mom and my husband won't be getting home for two more weeks. The dishwasher is a WhirlPool Gold Quiet


First check and make sure that the units not on a switched receptacle(and is wired into this circuit(i know the dishwasher is "hard-wired",as in the unit doesn't have a plug on it,but it could have been wired into this switched circuit by mistake) un ... Whirlpool Dishwashers

Whirlpool GU2300 built in Dishwasher. It rather suddenly began shutting off in mid-cycle. If I cancel or open it, getting it to finish the cycle or even drain takes many tries.Once started, the cycle might take several hours with long pauses during the cycle. When it puases, none of the lights are on at all. If the cycle is disturbed, the normal wash light blinks, and if I hit cancel, the cancel light and the normal wash light blink.


... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2604 seconds