Having problems with your GE 24 in. Profile PDW8700J Built-in Dishwasher ?

Dishwasher Problem The water won't pump out.


Answers :

Tuesday, start with the siphon break on the sink, if you have one. These will gunk up and prevent the drain. If the drain and hose are clear, remove the bottom panel and you will see the drain pump (WD26X10016) on the left side of the wash motor. Verify you have power going to it during drain. If you have the power check the flapper valve (WD01X10178) and the check valve (WD01X10176) that attach to the pump inlet. If you do not have power to the pump during drain, then you have a board issue. Catriver..post back.
Repair Help & Product Troubleshooting for GE 24 in. Profile PDW8700J Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Asko d3100 I have an asko d3100 dishwasher. Its just out of warranty and now the cup saucer light flashes and the water pump is continuing to pump even though there is no water. The dish washer wont start. What is the problem. I think the flashing cup saucer light is reporting a fault. If I know what the fault is for example faulty relay or pump then I can replace it. Can you help me with this one? Is there a service manual I prbably can get my hands on.


Remove the lower panel at the back of the machine. If there is water on the bottom pan, wipe it up with a towel or so, and the machine schould be like new again ;-)\015\012\015\012Good luck ... Dishwashers

EDW5500DSS wont completely drain water Okay so now that my dishwasher runs, when it finishes a cycle it has a nice puddle of water at the bottom that never drains completely out. I am assuming its a relay or something because I looked for a floating switch (did not find), I can hear a pump sound as if it wants to pump the remaining water out, but, it doesn't. I really want to solve this problem soon so I can order the new door seal and needed part together. Checked the line out and of course i


The srainer over the pump could be clogged not letting the water drain quick enough. Be sure the screen is cleane out. I believe you would have already checked and cleaned this. I believe it is the impeller on the pump that pumps the water that is ei ... Dishwashers

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

Asko diswasher Dishwasher will not get water. Lines all checked, water on. Pump runs even when in off. Problem started when there was a water clog in the sink next to the dishwasher, and the dishwasher backfilled with water. We used a shop vac to get the dirty water out. Next day tried to use dishwasher, runs, but no water and empying pump will not stop running. Ideas?


Check for water leaks or not draining/overfilling fault ... Asko D1776 Stainless Steel Built-in Dishwasher

I have a problem with my Asko D3350 Dishwasher, can you help? On startup the diswasher does its normal cycle and pumps excess water out and then fills the dishwasher with water to the correct level of water, after this the machine has no dishwashing action at all for the duration of the program setting. The dishwaher then pumps all excess water out and switches off as normal but no washing action has taken place, there are no error codes during the entire operation. Is there any way to rese


Hi Tony,\015\012\015\012I have the same machine (D3350) and almost the same problem.\015\012\015\012Mine starts each cycle fine - pumps out - fills - rinses - pumps out tht first load and then does not fill again. If I manuall ... Asko Dishwashers

I have a Kenmore dishwasher that will not pump water through the spray arms. It fills ok and drains fine but wont go into the wash cycle? Any idea of possible problems


Look inside of the dishwasher to be sure that the tubes leading to the spray arms are not disconnected. If those tubes are in place, then the problem is with the main motor/pump in the base of the unit. That Kenmore part is about $150.00 plus labor ... Kenmore 15762 Dishwasher

E3 Error Hi My dishwasher is showing error E3, which the user manual states "The appliance is not able to pump out the water.", however, other E3 error states a heating issue. The dishwasher does in fact heat the water but generates the E3 error after 10 minutes or so, then pumps out the water from the dishwasher. I'm a little confused as to what the issue is here and what part I would need to rectify the problem. Any advise you could give would be greatly appreciated. Kind regards


The E3 error is a result of water temperature not getting to a nominal value within a particular time. This could be caused by several factors like heater faulty, wash pump not working well, wash arms not circulating water as required. Need model nu ... Smeg Dishwashers

Hello we are having a problem with our Maytag stand up dishwasher. The water is not pumping out all the way and the water that is pumping out is pumping out slow. There is about an inch of water that is laying in the bottom of the dishwasher.


... Maytag 24 in. MSE760FAKS Free-standing Dishwasher

I bought this dishwasher 5 years ago and was kept in the box until last month. I installed it, turned on the water and no water is being pumped into the unit from the water release valve in the dishwasher. I then checked all the cycles and everything works except for the pump. Then I checked to see if any power/volts was going to the pump and there is none. Could it be a wiring problem or could it be the circuit board?? please help. thanks


You will have to check all the connections visually. Since you know how to use a meter, see where the current stops. See if there is current coming from the control board to the pump. the water inlet solenoid valve should "free flow" water into the m ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Shu9925uc/14 bosch dishwasher leaves standing water in the bottom of the pump. The pump seems to be bad because it wont drain out the back hose. I have run the diswasher full cycle and put the drain hose into the sink to test. It wont drain at all now and I dont hear the pump. Perhaps unrelated: Pump seemed to stop working after the back hose disconnected itself from the back of the unit spilling water all over the floor. When I reconnected the unit to the wall the pump now seems to be disfunct


Hi Dishwasher not draining issue occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remove then turn off the dish ... Bosch SHU9925UC Built-in Dishwasher

Ariston Dishwasher LSV 67 AIX wont fill with water pumps out only


You have been screwed!! ... Dishwashers

Hi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fine through all the cycles. The only problem is that it has no water pressure. In other words water is pumping into the dishwasher but it's like there is no pressure behind it to force it through the holes in the propellers so it's just kind of dumping water out as opposed to having any forced pressure. Hope this makes se


Water will flow out of your inlet pressure. The pump takes from your machine to spray. The same water is circulated during wash!Hence try the method I have informed you. If it is a micro controller problem you have to contact the service ... Dishwashers

Dishwasher model: se6 tie1 Fitted under kitchen work-top. Problem: After setting a program & switching on & closing door ? there is a normal sound from within but if door is opened there is no evidence of water being pumped in. I previously cleared food debris from the drainage pump area (including under the pump cover), checked the spray arms and checked the water supply was getting as far as the long in-take pipe. As it seems problematic to remove the (screwed in) dishwasher, I have not che


... Dishwashers

Hi there, Ok, i think i'mHi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fine through all the cycles. The only problem is that it has no water pressure. In other words water is pumping into the More Hi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fi


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. In\015\012this case you’ll need to check the water inlet valve. Disconnect the power\015\012source to dis ... Dishwashers

FDW60 dishwasher - taken apart pump and that is clear. Seems that dishwasher fills, and empties and heats all OK but water wont go around the machine ie the motor pump doesnt start - any idea how to take this out and replace without having engineer around? Taken small pump apart and its clear. First of all the Eco and fast light flashed, then we took it apart with some direction from online discussion advice. Now Eco and Pre wash lights are flashing. Machine empties water, then fills with


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Hi there, Ok, i think i'm getting close to solving this problem. I have an LG dishwasher- Model # LDS 5811ST. I have stripped it down and clean all hoses etc. It is running fine through all the cycles. The only problem is that it has no water pressure. In other words water is pumping into the dishwasher but it's like there is no pressure behind it to force it through the holes in the propellers so it's just kind of dumping water out as opposed to having any forced pressure. Hope this makes se


Try adding some more water to the machine after it has done the fill cycle do not over fill it. if there is no change in the performance the you need to replace the main wash motor.\015\012if there is achange the you need to change the fill val ... Dishwashers

Kitchen Aid model KUDS01FLSS3, water gets pumped into bottom of dishwasher but when the cycle needs to change to shoot the water over the dishes nothing happens. When the cancel button is pushed all the water will drain.I have cleaned out the bottom drain compartment that was jammed with calcium build up and guck. Would this be a pump /motor problem or electrical circuit board problem?


... KitchenAid Dishwashers

My Bosch Dishwasher does not drain all the water out of the dish washer after the finishing cycle...I usually start the washer and then push the drain cycle and it starts to pump for about 10 seconds and stops and starts and pumps again for 10 seconds and stops and then pumps for about 25 seconds and stops....doing this manual drain twice empties the dishwasher of the excess water....what may the problem be?


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

Kitchen Aid model KUDS01FLSS3, water gets pumped into bottom of dishwasher but when the cycle needs to change to shoot the water over the dishes nothing happens. When the cancel button is pushed all the water will drain.I have cleaned out the bottom drain compartment that was jammed with calcium build up and guck. Would this be a pump /motor problem or electrical circuit board problem?


... KitchenAid Dishwashers

I have Whirlpool dishwasher DWH B00. Now it starts as normal filling water for a couple of minutes. Then it suddenly starts beeping and pumps out all the water and just contiunes to beep. This will happen in all programs. We have studied the users manual and cleansed the filters as suggested in the manual, but this doesn't help. There are now problems with the water supply. The dishwasher is not used very much, may be just twenty times. In the start it worked normally, this problem suddenly


Hello & Welcome to FixYa If the sound is coming from the bottom panel then it is the motor that has gone bad and needs replacement. However, if you hear the sound from the control then it can be due t ... Dishwashers

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?


... Dishwashers

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?


Hi There,\015\012\015\012Your description seems to indicate a fault in the water heating circuit or components. This is often the reason for a wash cycle not finishing and draining. As the machine will drain when you lift the overflow lev ... Dishwashers

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Dishwasher keeps running I have a Bosche dishwasher and the water keeps running. As long as we run it and don't stop it, the pump will continue to drain about every 3 minutes. The water just keeps running though. If we open it to empty the dishes, the cycle will stop. But the water keeps running, filling the tub, and then overflows, flooding the kitchen and drains through our wood floors to the basement below. Our ASKO seems to have a similar problem. I started the dishwasher, and the water ke


Open up the door, get out the control unit. Pry open the unit's plastic case and look at the board. Burnt spot? If so, the heater circuit burnt out (happens a lot on Bosches) and the control is waiting for the water temp to rise, but of course it ... Bosch SHU43C05 Stainless Steel Built-in Dishwasher

My kenmore 665 dishwasher will not pump water to the lower and upper spinner arms. The pump entry screen assy seems to have one tear in it and is dirty. However water does come out if I take off the lower arm assy. Is this a sign that the pump is bad and is not pumping enough water to move the arms or is there another problem?


The pump is probably defective (low pressure). Enough to spin the bottom but not the top. ... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2109 seconds