Having problems with your GE 24 in. Profile PDW9280JSS Built-in Dishwasher ?

PDW9280J10SS dishwasher has been in use for about 3 years. The control panel is not working properly. I use the up/down arrows and it turns on heated dry etc. When I push the heated dry button, it changes the lights to the different cycles (which is what the arrow keys used to do). The normal wash light won't come on, the only setting that seems to wash a full cylce is antibacterial. It seems like something burned out. What should I be looking at as a possible cause/fix. Unfortunately, I don't h


Answers :

Repair Help & Product Troubleshooting for GE 24 in. Profile PDW9280JSS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

PDW9280J10SS dishwasher has been in use for about 3 years. The control panel is not working properly. I use the up/down arrows and it turns on heated dry etc. When I push the heated dry button, it changes the lights to the different cycles (which is what the arrow keys used to do). The normal wash light won't come on, the only setting that seems to wash a full cylce is antibacterial. It seems like something burned out. What should I be looking at as a possible cause/fix. Unfortunately, I don't h


... GE 24 in. Profile PDW9280JSS Built-in Dishwasher

I have a kenmore dishwasher model #655.1374 or 655.1384 which is only about a year old. I am having a problem with the controls. It will not allow me to use smartwash. The only control that can be used is quick rinse. I reset it by pushing Sani rinse and heated dry. All the lights come on and it seems to do a test. But after that still the same thing except if I push start resume it goes to normal wash which stays on a long time and periodically the cancel drain light comes on as well as the 4


... Dishwashers

I tried pressing the normal wash heat dry, normal wash heat dry several times, yes it reset my washer, but after a few uses, sometimes it will only run 5 minutes, sometimes it will run the full cycle. Then the green light starts blinking again. HELP!!!


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

I have a Kenmore 665.16039401. The 3 right hand buttons on the keypad; Delay Hours, Cancel/Drain and Start/Resume do not respond and I cannot start the washer. Doing the self-diagnostic test by pressing "Heated Dry - Normal Wash - Heated Dry - Normal Wash" results in all of the LED's lighting and the washer starting a full 20 minute self-test cycle in which all functions seems to work properly. Opening and closing the door during this testing stops and then re-starts the washer appropriately


... Dishwashers

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

Dishwasher wont let u select a cycle...all buttons seem locked...ive unplugged it for 5 seconds or so and then plugged it back in and the normal wash button light comes on and the heated dry button light comes on, but it wont start and it doesnt respond when buttons are pushed...please help. thanks


... GE GLD4560NSS Stainless Steel Built-in Dishwasher

My accusense light keeps coming on and blinks continuously. I tried the heat-dry, normal sequence and it would reset to 2 minutes. After the 2 minutes cycle, the accusensor blinking would begin again. Then I tried holding the heat-dry button in for 5-seconds. This looked like it worked so we set a normal cycle without heat-dry. Äll looked good, but a few minutes in, the normal light was off, the accusensor was blinking again and the heated-dry was on again! Is the unit possessed? Other id


... Whirlpool GU2400XTP Built-in Dishwasher

Dishwasher malfunction I have a Kenmore Ultra Wash Quiet Guard 3 dishwasher. One day, I found it with a blinking green ?clean? light. I went online to search for the manual, almost impossible to locate. Found a website where another using said to hit a 4 button sequence of ?heated dry? ?normal wash? ?heated dry? and normal wash. After this sequence, all lights went on and something that looked almost like a ?demo? sequence began (not sure now what that was). I hit ?cancel/drain? and it proceeded


Hi,The flashing light indicates that the control did not sense a 3 degree temperature rise with an 8 minute test. There are many reasons this could happen with a working heater. I put together a page that shows the reasons and you might b ... Kenmore 24 in. 15689 Built-in Dishwasher

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

I have a whirlpool dishwasher Quiet partner 2. I am using cascade detergent, my dishes coming out spotty. I have tried running with a very light load and the same thing happens. I notice that there is a white film around where the water comes out during a wash. I am running a normal cycle with heated dry.


Your problem is hard water. the minerals dry on your glassware causing a white film or residue. go to www.dishwasherfilter.com. they have an awesome product designed for yo ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Dub750x leaks My Whirlpool Quiet Wash Plus Series Model DUB750XB-0 dishwasher produces a small puddle of water on tile floor in front of unit, but it doesn't seem to be coming from underneath it as tile/grout right in front of it aren't wet. This happens hours after the dishwasher has been run, usually at night, whether on Air Dry or Heat Dry setting. This began occurring recently after years of use without the problem. Sometimes it occurs more than once after washing/unloading. Coul


... Whirlpool Dishwashers

[email protected] My problem: I have a GE Quietpower2 dishwasher. The normal wash and heated dry lights continiously blinks, the pump seems to be operating with no water present. I've tried turning the power off and using the reset button with no results. The lights blink even with the door open.


Hi,It sounds like the main control board has gone wacky....replace the control board.\012That is not that hard to fix and you can easily buy the partsyourself online...Here is a tip that will help you with the onli ... GE Dishwashers

My Kenmore model 665.16022401 has the problem w/ the clean light flashing. I tried the bottom combo of hi temp wash, heated dry, high temp wash, heated dry and it re-set my dishwasher but then after I tried to run a new load it doesn't seem like it finishes all the way through because there is still soap left in the soap dispenser and the dishes arn't all clean, plus the green clean light begins flashing again. Don't know what to do.


... Kenmore 24 in. 16022 Built-in Dishwasher

Here again is my model and serial it stops in the middle of the cleaning cycle Kenmore 665.16773402 serial # ft0302854 Here is how I have been resetting the dishwasher. I hit the following sequence of buttons: Normal Wash Heated Dry Normal Wash Heated Dry Normal Wash After that ? all the lights are lit up as follows: Smart Wash, Pots Pans, Normal Wash, China Gentle, Turbo Zone, Hi Temp Wash, Sani Rinse, Heated Dry, Sanitized (Green light ? not a button), Lock on (Red Light ? no


Door latch.Open and close the door to make sure the door latch is securely fastened\015\012 \015\012Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.Some models have options that may requi ... Dishwashers

Kenmore Elite Stainless Steel 24 inch tall Model 66577963K701. The heating element works for "heated dry" but not for "Hi Temperature" wash. It used to do so and when I opened the door a nice blast of steam would come out. My hot water tank is a great distance from the washer so we usually run the hot water tap in the sink for a bit until hot water comes... but the heating coil no longer kicks in on any of the cycles (Smart Wash / Normal Wash ). The high limit switch works and as I said, th


... Kenmore Dishwashers

After a power outage, that occured while the dishwasher was running, the lights come on and there is a high pitched noise. Then all the lights go off and the motor sounds like it is starting. However there is no water and the heating elemant comes on. The lights on the front; china/crystal, normal wash, clean and heated dry, all come on as if the computer is confused and trying to run them all simultaneously.


Sounds like the board was fried from a power surge ... GE Tritonr XL GSD6260JCC Dishwasher

Kenmore Ultra Wash Model 665 - 158* Front panel not working properly. Pressing Normal does not light that option. The only option that lights is "Quick Rinse", pressing this lights that option and also the "No Heat Dry" light. After a few seconds the lock light comes on. Looks to me that the "No Dry Heat" button is stuck on, which causes all the other things to happen Is there a way to fix this?


... Dishwashers

I have a Whirlpool Gold Quiet Partner III (Model GU1200XTKB0). I have used it previously on "Normal" cycle and I always keep it on Air Dry. Last night I used the "Pots and Pans" cycle and it seemed to work fine. But this morning the Air Dry light is flashing and if I press a cycle key the Rinse Only light starts to flash as well. Nothing works. I have made sure that the console is not locked. Any suggestions? I do not have a Heated Dry button, only Air Dry. Thank you.


... Dishwashers

Frigidaire FDB1502RGC0 dishwasher set for normal wash and heat dry option, both leds are on. dishwasher cycles through wash, but never makes it to dry cycle. After wash, the leds for OPTIONS high temp wash and dry cycle start blinking and do not stop blinking until I hit cancel - which cancels everything. Open unit and water sitting in bottom. Is it a bad operator panel? Water pump did seem to be working during wash cycle. NEED HELP.


... Frigidaire 24 in. FDBB540 Built-in Dishwasher

Global 450 dishlex dishwasher. Had the handle replaced 2 months ago. After that the ready light did not switch off as before. Now it only rinses. When you set the normal wash cycle the lights for Pre Wash, Wash and Rinse all come on. Pots cycle, the Pre Wash, Wash, Rinse and Dry all light up together, hence the machine thinks it up to that stage of the cycle. Can this be repaired or not. The machine is approx. 12 -14 years old.


... Electrolux Dishwashers

My frigidaire dishwahser was set to run a normal wash cycle and heat dry. It never ran, the soap is still in the holder and the lock beneath the heat dry option is lit. I'm unable to cancel or select any other options. I cannot get the dishwasher to run. Do you have a solution? I have tried holding down a number of the buttons in different combonations but still can't get the light to go out or start a wash cycle.


Looks like a number of things are happening.\015\012\015\012It would be easier if you can provide the model no. of your frigidaire dishwasher.\015\012\015\012I am assuming you have turned the mains power off and on. ... Frigidaire Dishwashers

DU1145XTP The buttons don't all work--for a while the normal wash and heated dry were the only functions that worked--now the start button doesn't work. I took the panel off and clicked the door switch and held it and got all the cycle buttons to light up except rinse only and only heated dry in the cycles would light up. The delay buttons don't work and neither does start. Also the panel seems hot.


You need to replace the circuit board inside the machine, technically it is possible for you to do it, how long have you had the machine, if it is under warranty you can have it serviced without any cost or less cost to you contact Whirlpool ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

I have a Whirlpool DU1048 that started out with a blinking clean light. I reset the dishwasher by pressing the heated dry and normal buttons twice. That worked the clean light stopped blinking. The problem now is the dishwasher seem to be stuck in the wash cycle. I finally have to turn it off after over an hour washing. Is this possibly a heating element problem? is that user replaceable?


... Dishwashers

Replaced circuit board on my kenmore 665.13742k603 dishwasher,still all wash buttons,and start button will do nothing.ran test using sani rinse and heated dry buttons all lights come on but washing light does not,all lights remain on after test,unplugged,plugged back in,,still no wash buttons or start buttons work,can you help?


... Dishwashers

I have a Sears Kenmore Elite Ultra dishwasher 665.1315 model. For the last 3 weeks, it keeps having the clean light blinking 6 times pause then 1 blink and pause and repeats cycle again. I have turned off the breaker...I have reset by pressing the heated dry and normal wash until all lights are flashing. It then completes some type of cycle and looks ok. When I opened the door, steam came out and all was hot inside. However, once I try any new wash cycle, it seems to wash but after 1-2 hours and


Call sears service and tell them you need service there is a service flash and will be no charge ... Kenmore 24 in. 15932 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2121 seconds