Having problems with your GE 24 in. Profile PDW9800J Built-in Dishwasher ?

The GE Profile Dishwasher will not allow me to start without the heated drying light coming on. I want to wash without this headed drying at the end of the wash. When I try to turn it off it turns the start cycle off. This happend over and over again when I want to turn on the machine, It finally lets me get an unheated dry wash started to complete. A problem every night. PDW7800N15CC. Serial MM8243388


Answers :

Repair Help & Product Troubleshooting for GE 24 in. Profile PDW9800J Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The GE Profile Dishwasher will not allow me to start without the heated drying light coming on. I want to wash without this headed drying at the end of the wash. When I try to turn it off it turns the start cycle off. This happend over and over again when I want to turn on the machine, It finally lets me get an unheated dry wash started to complete. A problem every night. PDW7800N15CC. Serial MM8243388


... GE 24 in. Profile PDW9800J Built-in Dishwasher

After the wash & dry is complete, the next time I try to use it, won't turn on. I tried cancel and that starts and finishes but can't get any thing else to work. I turned off the circuit breaker but have to wait 6-8 hours before turning back on. Once this is done the machines runs normal again. I have to repeat this process every time I want run. Any suggestions on what might be causing this???


I have the same problem. The only temporary solution I have so far is \015\012to turn off the circuit breaker and wait between 10 & 30 minutes \015\012before resetting the breaker. The the dishwasher will work for one \015\012cycle. ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

I have a General Electric pdw7880J03ss dishwasher. Tonight, I went to start a load of dishes and the Heated Dry option wouldn't turn off without the lights going to RINSE ONLY. Then the 1hr setting started coming on. Then was able to get the load to start but then it stopped somewhere in the cycle. Now, no lights will come on the panel though I can hear the beeping. Dishes appear to have washed...


Hi\015\012\015\012Press and hold the heated dry button for 15 seconds to reset\015\012the control, if this wont work then it means that the control board is bad and\015\012should be replaced. Hope this helps...please post back for further ... Dishwashers

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a


The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

I have a Triton dishwasher. Last cycle, it completed washing then started drying and started beeping and the drying light is flashing. When I finally opened the latch, the beeping stopped, but the drying light is still flashing. The dishes were clean and warm - they air dried the rest of the way. I have not been able to get the drying light to go off. I have turned the breaker off over night, and flipped back on. The dishwasher goes back to flashing washing, and then clicks to drying and th


Hi,\015\012Make sure the salt level is ok - add 1Kg of salt if you have not done it in a while, and check rinse-aid level if apliccable.\015\012\015\012If this does nothing, then remove the lower kick panel for access to a data shee ... GE Dishwashers

We have a Kenmore Ultra wash dishwasher Model # 665.13733K601 and serial # FW18136133. came home from work yesterday and the pots and pan button and the normal wash buttons were flashing alternately. When I pushed the cancel button it started to flash, then I pressed the smart wash button and now its flashing. I turned of the breaker for awhile and then back on and the lights weren't on right away but later started flashing again, and I can't get the dishwasher to do anything. Any help on my pro


Hi,\015\012That unit took a power surge and the control is now bad....those controls can all of a sudden go wacky and the usual cause is power problems...\015\012The only way to fix it will be to replace the control...\015\012 ... Dishwashers

I recently bought a condo with Fridgidaire appliances. The previous owners did not leave the manuals. (which I was wondering how I could get copies) My problem is with my dishwasher Model# FDB700BFSO, Serial#TH73478655, I like to use the short wash, so I turn the dial to that section, but to get on the right spot for it to fill is very difficult. I find I'm going past and around, trying very slowly to get it just right with the correct setting. Hope this isn't too confusing. All I want to d


... Electrolux Dishwashers

I have a GU1500XTLB1, type-575-0 Whirlpool Gold dishwasher. For the last couple of weeks I've been getting the control lock on. I got the manual out, I hold the air dry button and it clears. My problem is now when I turn the machine on dosen't matter which cycle I hit (pots and pans, normal, or quick wash) it runs for about 5 minutes and it goes into a mode with the timer having lines going horizontal with the air dry button lit up and rinse button lit up. It sounds like it starts the cycle


Hi,There are Few Tricks to Reset this. Follow the below Tricks :-1. Try holding down heated dry key for 5 secs. I believe that is the control lock/unlock button on your model. IF not, look for the lock symbol and follow same i ... Whirlpool Dishwashers

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Have a kitchenaid dishwasher KUDS25SHWH1 - the child-lock light came on and will not go off. It is a light and no button to push and hold except all of the select buttons for the type of wash you want, no air dry button. How do I get this light off?? The Child Lock light has come on by it's self and I cannot get it to turn off. I have never used this feature before. I have tried to hold the Energy Saver button for several seconds but the Child Lock light will not shut off. The dishwasher is loc


Unplug the unit for 15 minutes then plug it back in. This should reset all your computer system and make everything work again ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

I have a 1 year old maytag dishwasher and it has the touch buttons on top of the door . When you touch the buttons to turn it on, nothing happens. It will light up the type of wash you want e.g. heavy,light...., but it won't start when pressed. It will cancel when pushed, but can't get it to start. HELP!!!


... Maytag Dishwashers

Last month i was washing dishes in the dishwasher and if i remember correctly i opened the door to get a knife out of the dry cycle. i remembered shuting the door back and that is about it. this is my daughters dishwasher by the way. i left her house not noticing that the dishwasher ever finished. a week later she asked me if i had a problem with it. i told her no. when she goes to push the start button nothing happens. it doesn't restart its self. we have turned the breaker off and on


Hi.Depending on the model you may need to reset the dishwasher. Most Kenmore and Whirlpool built dishwashers for example need to press a reset button sequence to operate again after a problem has occurred. In that case you usually get lig ... Dishwashers

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

Several people have posted this problem with the Frigidaire Ultra Quiet 111, but I have seen no solutions. When it is set to wash without extra heat, it cycles normally. But when the extra-heat wash and extra-heat rinse are selected, then it gets stuck first mid-wash at the 7 o'clock position, and if it is manually advanced then it gets stuck again during the rinse cycle just before the 9 o'clock drying position. Both the wash and rinse thermostats have been replaced without solving the problem.


Hi,\015\012\015\012I know that you are going to think that this is dumb... but the only thing that it can really be is the timer....\015\012\015\012 ... Frigidaire 25 in. FDP750RC Free-standing Dishwasher

Have a 665-16293201 dishwasher with electronic controls and smart sensor. Approx 10 years old in great shape. it just started having a problem - it takes a long time for the sensing to be completed at the start of a wash and then the washer will start and display a time - like 92 minutes - turn the sensing light off, then start to wash and count down. when it gets to 86 minutes, it starts to sense again and will continue washing while displaying 86 and with the sensing light on. It will keep


... Kenmore 24 in. 16293 Built-in Dishwasher

My frigidaire dishwahser was set to run a normal wash cycle and heat dry. It never ran, the soap is still in the holder and the lock beneath the heat dry option is lit. I'm unable to cancel or select any other options. I cannot get the dishwasher to run. Do you have a solution? I have tried holding down a number of the buttons in different combonations but still can't get the light to go out or start a wash cycle.


Looks like a number of things are happening.\015\012\015\012It would be easier if you can provide the model no. of your frigidaire dishwasher.\015\012\015\012I am assuming you have turned the mains power off and on. ... Frigidaire Dishwashers

FDW60 Fault Hi, I have exactly the same problem. My dishwasher starts and washes ok but appears to get very hot during the drying phase and then the two lights fast and eco flash warning of a heater problem. I suspect either the heater, thermostat or control PCB. As the rest of the cycle seems of and the water gets hot then I'm assuming the heater and thermostat are OK. When the dishwasher attempts to dry is when the problem starts. Did anyone find out what there fault was? Thanks


Hold down the start key and you will re- set the D/W. Please Rate This !!! Thank YOU !!! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

My kitchenaid dishwasher won't wash. The clean light blinks and if I can get it to cycle, it turns on to ''2 minutes'', during which 2 minutes it makes some washer-like sounds but doesn't clean, dry or spit out any water. Before this, I wash having trouble getting my dishes clean. I wash able to get the bottom rack clean using the heavy duty cycle, but the top rack still didn't clean


... KitchenAid Dishwashers

Kenmore ultra wash quiet guard dishwasher, the pots and pans and the normal wash button are blinking. The start and cancel and smart wash out tons have a faint light glowing. Thoughts? I tried the sequence of pressing heated dry, normal wash, heated dry, normal wash and that did nothing. I've flipped the breaker too. I was in process of taking it apart to clean filter, thinking that would help, but lost my manual and now I can't get that off to flea either:(. Sig


... Kenmore 24 in. 15689 Built-in Dishwasher

I have a Whirlpool Gu180 ESJQ with a blinking green start light. If I clear this light (hold the start button for 5 second to place it in the end of cycle) then I can get it to start another wash cycle. However, the next wash cycle ends with a blinking start button again and the dishes aren't dry. I had an appliance service man come to check it out and he could not detect any problem! Now I have a leak!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Haier hdw101wh.The dishwasher starts when you turn the dial the pump discharges waterto the outlet it clicks to next cycle but remains washing will not cycle through the wash cycle it keeps on washing . You have to turn it manually to get it finished any info will be appreciated.


... Haier Dishwashers

Initially It started washing, completed the entire cycle, then while drying began re-washing the load. Then it would start washing nothing, without any buttons pressed. Then it woldn't allow any buttons to be pressed for any cycle.Then the lights would flash, but nothing would progress through the cycle.


For replacement parts - head on over to PartSelect.com or \015\012RepairClinic.com and enter in your full model number for a full parts \015\012listing.\015\012I recommend both sites because ...\015\012\015\012\015\012FixYa ha ... Whirlpool GU2300XTVQ Builtin Dishwasher

My Maytag MDB7609awb2 dishwasher has a glitch When I try to turn it on the heavy and light was lights go on but won't start the normal wash light won't go on at all until I keep pushing the off and on for a while, then suddenly the normal button works and start will start the machine, then is washes without any problem.


... Maytag 24 in. MDBH955AW Built-in Dishwasher

Maytag MDB 8600 AWB dishwasher Wouldn''t start... just a Heated Dry light. Replaced (already broken) door handle with complete latch assembly. Still, Heated Dry flashes. Tried various suggested combos of 5 or 6 quick button pushes followed by Start. Only get a 50-=countdown that repeats endlessly. Sometimes alternates with the letter L. Once by luck I guess it went into Heavy Wash mode, or at least the diagnostic for it. Completed this fine, then back to the stubborn Heated Dry light.


... Maytag 24 in. MDB8600AW Jetclean II Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1863 seconds