Having problems with your GE 24 in. Profile PDW9880JSS Built-in Dishwasher ?

Our GE Profile Dishwasher is not working since today afternoon. The electronics seem to be working fine but the water supply does not start on pressing the start button. The dishwasher seems to go on with its cleaning cycle without water. We don't know how to fix this or to even check any plumbing/water supply problems. Please help.


Answers :

OK First try this below....\015\012\015\012Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing.
Now this happens because, the STOP Button, is pressed and the "Door Opened", during the Wash Cycle. This should NOT be done. You shouldNEVER TURN IT OFF MID-CYCLE. you should instead, Simply, pull on the handle, to Open the door, the system will take care of everything, after, you close it,and pick up where it left off. The turning OFF, makes the machine "Think" that a New Cycle, is going to be done, before the old one is finished, and resets itself to do it all again. But it still has water, that's not meant to be there so it must dump it out.
Now, the FIX. Take the Dishwasher, out, and tip over on it's side, tip to about a 45' angle. Water will come out from underneath, this is from a small "Overflow" reservoir. this reservoir has an "Anti-Flood" switch. The removing of this water will "Reset" this Switch, and allow the dishwasher to work again.
So what happens, is this, when the STOP button is pressed Mid-Cycle, the machine must "Dump" whatever water is still in the machine, into the "Overflow Reservoir". This water then causes the Anti-flood switch to jam, and this stops the machine, until it is reset,by the above method.
Hi
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks\015\012for using FixYa. To start with check the water inlet valve which is located\015\012behind the lower access panel on the left or right side of the Dishwasher. If\015\012the water inlet valve is bad you have to replace it, also check the main water\015\012line for clogs/obstructions. If still the issue is not resolved then it’s a bad\015\012float switch and needs to be replaced. Please do accept the solution if the\015\012issue is resolved or else revert for further assistance.
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks
\015\012\015\012Rylee
Repair Help & Product Troubleshooting for GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our GE Profile Dishwasher is not working since today afternoon. The electronics seem to be working fine but the water supply does not start on pressing the start button. The dishwasher seems to go on with its cleaning cycle without water. We don't know how to fix this or to even check any plumbing/water supply problems. Please help.


OK First try this below....\015\012\015\012Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hu ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

My Frigidaire dishwasher won't start. I just moved into a condo and the dishwasher worked during inspection but now it's not...wondering if it's something I just don't know about. The model number is fdbb944CS0. The panel lights up when you select the different cycle options but when I hit start nothing happens. The control panel isn't locked either- I saw some forums about that. The water supply is on...help!


Did you ever get an answer to your problem.\015\012\015\012I've got same issue where I turn the diswasher on and nothing happens ... the time just start going down but nothing is happening? ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

Hello, I have a CONSTRUCTA S9W1C dishwasher with aquastop. Unfortunately, I tried once to start it with the house water supply closed. Of course it stopped after a few seconds. After that time, when I start it, the water pumps works and after some seconds the cycle stops. It gets no water. I've checked and noticed that no water passes through the aquastop valve. The aqua stop has two wires that get into the dishwasher. Do you have any suggestions? Thank you for your time Alex


... Dishwashers

Dishwasher will not fill with water, dishwasher sat unused for some time. it worked fine for 4 times, then it backfilled with water from the garbage disposal unit, and leaked out through the floor. When I start a cycle we hear what it sounds like a pump draining and then going to cycle without water coming in. It's a bum.


... Bosch 24 in. SMU40 Built-in Dishwasher

I have a Bosch Dishwasher, Model SHE46C06UC. No mater what cycle I start it in, it simply activates the drain and continues to run without ever starting. Within the last week prior to the dishwasher not working, I noticed a low hum/vibration emitting from the dishwasher. I've clean out the screen and drain filter, removed the pump cover to check for any debris. I've manually added water and it does drain. Additionally, the drain cycle continues to operate even with the door open.


First thing you may want to check is the door switch. You can pull it off and measure the resistance with an ohmmeter. If you get good reading while pushed in and none while switch button is released, then it is a good start. Next, you may want ... Dishwashers

My KitchenAid Model KUDE70FXSS 2 dishwasher is new to us today and has never been used before. It was hooked up professionally, but I assumed it would work, so tonight when I tried to run it, it lights up on panel, but it won't run any cycles. It will start putting water in the machine, but then cuts off. It starts making a grinding noise underneath the machine, and it clicks like it is trying to work, but the water doesn't wash. Hmmm. Anyone know what to do?


... KitchenAid KUDE70FXSS Builtin Dishwasher

The dishwasher starts and initially rinses the dishes without heated water. In the next part of the cycle, the water is supposed to heat to a certain temperature.Beginning this morning, in this second part of the cycle,the dishwasher trips the circuit breaker. If you reset the breaker and turn the sihwasher back on, the breaker trips again. What is wrong and how do I fix it?


Hi\015\012\015\012The issue is with the heating element of your dishwasher, it is withdrawing very large amount of power and thus, the circuit gets overloaded and circuit breaker trips. You'll need to check for any short circuits around t ... Dishwashers

Dishwasher works fine except that after the drying cycle, water slowly builds up in the bottom of the dishwasher. It did this a few years ago for several months, but then it stopped doing it altogether. I did nothing to fix it. Now it's started doing it again. I run the dial around to a point where it drains, let the water drain and then turn it back to off before the drying cycle begins.


Hello,\015\012\015\012This would mean that the dishwashers water valve has failed. This is a simple repair to make yourself. The lower access panel would need to be removed, four screws. You can purchase the part from the link below.\015\012 ... GE Dishwashers

Whirlpool Dishwasher ADG 450. Start as normal and it keeps intermittentlly stopping and starting. Washs / drains fine, but sometimes cycle seams to last for a couple of hours. I think it is four beeps when it is stopping and then immediately starts again. We had a problem months ago where as the sink was draining into the dishwasher out pipe, so dishwasher wasn't draining / filling up. Fixed the problem by turning the pipe the other way so water couldn't flow that way - but I don't know if that


... Dishwashers

My dishwasher was recently 'installed'. i don't know if the contractor made a mistake or if the water valve is not turned on, but the cycle tries to start but then no water is flowing into the dishwasher. everything appears to be hooked up, but I think it's the water issue b/c i also have a new refrigerator and the water dispenser/ice maker does not work because no water is flowing into the fridge either.


This sure sounds like a water valve issue, for sure. You will have to trace out the lines (not easy, but possible) and figure out where the valve is. They usually turn left to open, and right to close. I would call the contractor and tell them ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Hi Dishwasher BOSCH SMS53L02GB start of program digital display shows all sensor working. Water not pumping in. All hoses and filters checked OK Machine pumps water out then completes cycle in 1 minute. Water supply getting to base of machine An E21 code shows up on fault finding cycle


... Bosch 607335 Water Valve Assembly For Dishwasher

Dear sir In an attempt to dislodge a blockage of my sewer line using Draino and a plunger some of the Drano ended up in the dishwasher and now the dishwasher will not run. My dishwasher is a SHU3036UC/U12. When starting the unit up it empties the unit but the cycle newer ends, in other words the timer does not advance to the next cycle, I have determined that the timer motor works by removing it from the unit and supplying it with power. One thought is, can the water level switch be stuck in


HiCheck this video and clean the drain pump assembly: ... Bosch SHU3036UC Dishwasher

I had a problem with my dishwasher popping the breaker. I opened the bottom and found burnt up wires. I fixed those and now the dishwasher stays on and begins its cycle (by draining) but the water is not flowing to the machine. It has supply, and I just now replaced the water inlet valve- no difference. The water was working before the breaker issue. I'm wondering if it is now something as simple as a clog somewhere since the washer sat unused for a month; or, if it is something more compli


I read your previous problem. This appears to be separate problems. The first was likely a loose wire. When a wire has a loose connection they build heat and can melt. The current issue would seem like the float switch is stuck. The float switch is ... Bosch SHU9925UC Built-in Dishwasher

I have a EuroTech dishwasher Model# EDW254E/SB. It was working fine but now it gives the Err code:er1 Its not letting incoming water in i know that. As well I have been told to try reducing the water pressure at the facet. Did that nothing.It drains but wont cycle to the next stage and let water in. I am presuming there is a valve of some sort not opening? And does the dishwasher have to be completly romoved to fix. Thanks


Hi and welcome to FixYa. I am Kelly. \015\012\015\012This is a water level sensing problem. Look inside your lower wash tub area and see if you either see a circular device off to one side or a finger like device sticking up about 2 inc ... Dishwashers

The dishwasher starts it cycle and fills with water, but the sprayers do not engage and it just continues through it's cycle without the sprayers working. It will drain the water, but the spraying arms do not turn nor spray water.


... Kenmore 16879 Built-in Dishwasher

Hi There, I have a frigidaire FDB1502RGCO dishwasher and I have power and water going to the macine however when I turn it on it will not start its cycle. Washing light is lit and all functions are lit up as normal on the front panel however the cycle does not start. Is there a simple fix or reset for this machine or will I need to call technical support to have a technician come to look at it? Please let me know. Thank you


... Frigidaire FDB1502RGC Built-in Dishwasher

I have a bosch smu 2000 series dishwasher. it has always worked well with no problems but then all of a sudden a week or so ago, the water stopped coming into the dishwasher to wash the dishes. the faucet and all other water areas continue to work w/o problems (i.e. bathroom, shower etc). in attempting to use the dishwasher, the entire cycle seems to be working, i initially hear what sounds like an initial water discharge when the cycle first starts and during the entire cycle it sounds like it


... Bosch Dishwashers

Hello, my Siemens integrated dishwasher no: SE64M359GB stopped working mid-cycle with 35mins remaining. It is displaying the red tap emblem. Usually the dishwasher starts when the dishwasher door is closed fully (having pressed the power button). However, it is making a noise as soon as the power button is pressed. I have checked the water supply and pipes and they are OK. The filters are also clean and OK. We have an electric de-scaler on our system so I imagine calcium build up should n


... Siemens Dishwashers

When I hit the start button on my dishwasher nothing happens. It still "finishes" the cycle but nothing ever cuts on. It doesnt fill with water and the sump pump never engages to drain the water that's not there. Any ideas? I know the inlet water pump works, I've detached it and connected it with a pigtail to an outlet.


Replace the main control board ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

I have a Bosch integrated dishwater that is just over 2 years old. It has suddenly stopped working and the tray at the bottom is not emptying, although you can still hear a buzzing sound. The cycle does not go beyond this point. I have emptied the tray of water and the dishwasher will start again, and pump water in, but it then stops, as though it is not able to pump water out. Does anyone know what this is? Could it be the pump? A blockage?


... Bosch 24 in. SHU43 Built-in Dishwasher

The dishwasher will start to cycle. I can hear the water begin to run. I hear a click and at the time the dishwasher should start to run the cleaning cycle. During the cleaning cycle the dishwasher will stop working. The dishwasher is silent. The timer will continue and the water will drain out at the appropriate time.


This is probably okay, you have clock like motions running the motor electric contacts. There needs to be a delay between some cycles or shorting will occur. The motor on some designs, for example. is reversed to pump out water. to have this work lon ... Viking 24 in. Professional Series VUD040 Stainless Steel (Premium) Built-in Dishwasher

I have just bought a cid60b10 dishwasher and it won't work! I completed the first wash putting water in the salt dispenser as instructed and when it had finished the wash there was still water in the bottom of the washer. Now when I turn the machine on all the buttons light up and then go off and I cannot select a function. Does anyone know how I can fix it without having to send for a technician?


... Dishwashers

My Maytag dishwasher model MDB7130AWB started making a grinding noise tonight during drain cycle. We just had some work done on the sprinkler system and the water main to the house as well as the check valve for the sprinkler system have been turned off and on a lot the last two days. I noticed that we had some dirty water come out of a sink in a bathroom, after that repair. Don't know if that could be related to this problem but it was worth mentioning.


Shut off water to the machine, remove the hoses at the machine and inspect & clean the mesh filters in the water inlets. If dirt did get into the line, it would be from the water main work, not the sprinkler work.It doesn't hurt to clean the ... Maytag MDB7130 Dishwasher

My CDA WC 350 integrated dishwasher will no longer perform a cycle, it seems to start working then stops after a few seconds and starts beeping, when i open it, i get 6 flashes of the LED. Can anyone identify the fault, and let me know how to fix it please?


... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2423 seconds