Having problems with your GE 24 in. Profile PDW9880JSS Built-in Dishwasher ?

I have a GE Profile dishwasher that stopped working after being unplugged for about 24 hours. Now only the timer lights up and no buttons work. Do I need to reset something after being unplugged so long?


Answers :

Repair Help & Product Troubleshooting for GE 24 in. Profile PDW9880JSS Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a GE Profile dishwasher that stopped working after being unplugged for about 24 hours. Now only the timer lights up and no buttons work. Do I need to reset something after being unplugged so long?


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have a whirlpool dishwsr. model GU2400XTPB7 that has been flashing the normal light and I cant use it for over a week. I turned off the breaker to the house for 30 min. & that did not work. I tried the reset sequence of Htd dry/normal, repeat, repeat & that did not work. If the push button "panel" needs replaced is it something that a "handyman" can do?


Hi Melinda,Thanks in advance for using Fixya.com. Now then firstly by pushing the heated dry and normal buttons then repeating is the proper procedure to reset the control board,below is a the exact buttons to push to reset the control. Also plea ... Whirlpool Dishwashers

My Maytag dishwasher goes for long stretches when it won't turn on even though I push the proper buttons. The buttons won't light either. It turns on by itself after a couple of weeks of sitting idle. Some of the lights may blink on the start panel while the dishwasher doesn't work, but only on occasion will it fully operate. I have turned off the power and turned it back on, hoping to reset the computer part of the dishwasher. It didn't work.


The Control Touch Panels like to fail on may brands - especially Maytag. They are sensitive to humidity - and a lot have the vents out the front - right by the control panel.Please reply using "continue with this expert ... Maytag Dishwashers

I have a Kenmore 665 ultra wash quiet guard 3. The red light at the start/resume button flahes continuosly. I have unplugged it and tried the four button reset. Neither works. The red light still flashes. Any ideas?


The /RESUME light flashing constantly means that there is either have a bad door switch or a touchpad failure.In some case the problem is a faulty control board.The control board cannot be returned.I suggest replacing control pad fi ... Kenmore 24 in. 15689 Built-in Dishwasher

Maytag dishwasher. The clean light stays on solid until I press any button then it blinks for several times then goes solid again. None of the other buttons light up when pressed. I unplugged it for over an hour to try to reset it but that did not help.


... Maytag MDB9600A Jetclean II Built-in Dishwasher

Help! My Whirlpool Quiet Partner II isn't working at all. Water was standing in bottom at end of last 2 cycles, but on the last cycle, I came home to clean looking dishes, standing water, and a machine that won't turn on at all- no lights on any buttons- nothing works. I've tried the reset codes published here and elsewhere, but there are no lights on any buttons at all. The circuit breaker is fine. I have 3 young kids and can't function long without my dishwasher!


There is a fuse in the control panel what your model# i can get you the part number its easy to replace it. ... Dishwashers

Hi I have a Fisher & Paykel dishwasher model dw681es, the start & reset buttons light up but the machine won't function. Is there a special reset button or something else I can do? Thanks.


... Fisher and Paykel Dishwashers

Whirlpool GU2400XTPT Dishwasher is on island of Utila, Honduras. Upon return after several months absence, light was flashing but dishwasher would not turn on, light would not turn off, no other buttons would light up. I am thinking a power surge might have hit it and maybe knocked something out. Problem is, I need a part from here to take down there and hope someone there can install it. Help! Thanks! Barbara Chaney


I had a svc. tech come and he said I need a new "panel". Darn.It's $133 plus labor. He said the "normal" button had shorted out,especially since that's the wash I use all the time. It's only two years old, and I didn't buy an extended w ... Whirlpool GU2400XTP Built-in Dishwasher

Indicator lights on Maytag dw model mdbh 955 do not light up. Plugged into live plug. Door is engaged and clicked shut. It's like there is no power to the unit but there is. Is there a reset button I need to check or a fuse?


Hi,Follow the steps :-\015\012\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is\015\012there power getting to the dishwasher? This can be difficult to test,\015\012because dishwashers are usually wi ... Maytag 24 in. MDBH955AW Built-in Dishwasher

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

Kenmore Ultra Wash Quiet Guard 4 Dishwasher model 665160344000 normal wash light keeps flashing. I have done all of the push this button and that button combinations I can find on the internet. I unplugged and repluged the 14 pin ribbon with power and without power --no joy. Looks like I need a new part - which part?


Hi\015\012\015\012Open the door. Within 3 seconds press the following sequence\015\012--Try pressing normal wash, heated dry, normal wash, heated dry, normal wash,\015\012heated dry three times within 6 seconds and then press cancel to re ... Dishwashers

I have a miele g892sc+. The train/intake light comes on and holding the start/stop button for five seconds does not reset. I've cleaned the filters. But it appears to be stuck trying to drain. Since the reset doesn't seem to work it's hard to tell if that would 'fix' the problem or if there is actually something else wrong.


The END, START/STOP & TOP SOLO all flash at same time ... Miele G892SC SS Dishwasher

Kitchenaid kudp02cr Dishwasher has a blinking drying light during wash cycle, when we cancel it shows the washing light on soild. We have tried resetting the panal, but it isn't stopping. WHat do we need to do and is something wrong with the system.


... KitchenAid 24 in. KUDP02CR Built-in Dishwasher

I have a kitchenaid dishwasher, SS, model # KUDIO1ILBL6. When you press the ''normal'' button to run it, nothing happens. Tried other cycles and same thing, the green light goes on above the cycle but its just not starting. I tried resetting by opening, pressing high temp scrub then energy saver dry, high temp scrub, energy save dry, then close and hit cancel. Is there any other combo to reset it? or does it sound like something else is wrong? thanks!


... KitchenAid Dishwashers

KUDS02SRSRSS1 dishwasher.......remodeling kitchen, disconnected dishwasher.....reconnected and have power (lights are working), however when hit start or cancel button on front door, nothing happens. Is there a "reset sequence" of buttons that I need to press?


I am assuming you have tried to turn the power off and on again after a delay.\015\012\015\012Most likely the door switch is not engaging. Have you tried to push the door a bit hard. Sometimes the dishwasher is not aligned correctly with ... KitchenAid 24 in. KUDS02SRSS Stainless Steel Built-in Dishwasher

I have a Kenmore Type 575-0 Dishwasher, model number 665.16033401, Style 16033. It runs trough the cycle, once the cycle is complete the clean mode light is on but most dishes are still dirty. I had someone here to repair this about a year ago. All he did was press alternating two buttons, which I have tried, it resets and lets you start a new cycle. However, the problem remains. Last time there was only button pressing involved, no need to replace anything. So, I would hate to have to pay ag


You need an electronic control and heating element ... Dishwashers

Have a ge nautilus dishwasher, all the light in front works, except the start button will not light up, tried unplugging the power to reset unit, still do not work, any suggestion


... GE 24 in. GSD4060JSS Built-in Dishwasher

Whirlpool model 927 built in with electrical push button panel won't start. I have tryed unplugging for 30mins to reset which didn't work. When the panel buttons are held in for about 5 secs the red light flashes. I don't know how to check for panel or motor failure. Any ideas?


... Dishwashers

I have a Whirlpool Gold Model GU2700XTSBO its only 4 years old. About two weeks ago i noticed that the green lights were flashing and it would not run, I unpluged it for an hour and pluged it back in and the lights went away and it worked ok for the last two weeks. Last night I went to use it and there is no power at all to the washer, I checked the power source to the outlet and there is power there, so I dont know if there is a reset button or some control panel problem?


... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

KUDI01ILBL6 Kitchenaid dishwasher is blinking the Rinse light. Upon pressing any button, the Cancel, Normal and Rinse Only lights are blinking. Does this "code" mean something specific? How can I reset the board?


... KitchenAid Dishwashers

My TEKA Dishwasher DW6 59 F1 starts the cycle makes all the noices but does not heat up & 2 lights light up, i have been told if you locate the reset button, it will resolve the problem?


... Dishwashers

Kenmore 74362 My model# is 665.74362400 this unit is only just over one year old. My problem is it shut down and the quick rinse light started blinking. I have tried some of the button-reset procedures that were on some other responses but to no avell I even left it unplugged for a while. Any impute would be appreciated. I have a Kenmore Dishwasher Model #74362. After we run a cycle for a normal wash and heated dry the dishes are all very dirty and greasy. It is as if they were never washed. Th


I had the same issue and you will never beleive the solution.\015\012Steps to follow:\015\0121) run one full cycle with no dishes or soap\015\0122) run one full cycle with a dishwasher cleaner like Jetdry\015\0123) run one ful ... Dishwashers

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

Whirlpool DU1145XTPPB7 Whirlpool DU1145XTPB7 model. Normal cycle light started blinking sometime during end of wash cycle. It will not do anything. Things I have already tried and not worked: 1. Unpluged and pluged unit back in. 2. System reset w/ heat-dry button, etc. Any help would be greatly appreciated


These dishwashers normally have a "Control Lock" mode.  It's in the manual.  It is provided for child safety.  It's often controlled by holding the "No Heat Dry" button for 4 seconds or more -- same procedure turns it on or off. ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1471 seconds