Having problems with your GE 25 in. Nautilus GSC3400J Free-standing Dishwasher ?

The Motor is running but will not fill with water. I checked the water supply and drained the water out but it still will not fill with water.


Answers :

I have a gibson energy saver disheasher and the water will not fill. motor is working
Assuming I have all this straight, I have the same model with a plastic interior. There is a little upside down cup looking device up front on the far left. Apparently if you tap on it, it helps. Ok, I banged on it a bit and went beyond the tap GE recommends. It just worked with mine, thank GOD! It's the day before Thanksgiving, need one that works.
Repair Help & Product Troubleshooting for GE 25 in. Nautilus GSC3400J Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The Motor is running but will not fill with water. I checked the water supply and drained the water out but it still will not fill with water.


I have a gibson energy saver disheasher and the water will not fill. motor is working ... GE 25 in. Nautilus GSC3400J Free-standing Dishwasher

I have a fridgidaire Gallery dishwasher model # FDB949GFS2. It was not spraying water while running, so I checked for clogged wash arms and hoses etc. So I replaced the motor assembly and now I hear the motor running, it fills with hot water but it is still not circulating water. Is there something else I need to check. Thanks Tom


Most likely the wash sump is blocked. Refer this diagram. You will have to open the sump (item 14) and loo ... Frigidaire FDB949GF Dishwasher

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

Maytag Dishwasher Model MDB4100AWQ When I start the Light Wash Cycle: Washer fills with water, heater comes on (I checked it with a volt meter--120 volts), timer runs, motor never runs, before the timer gets to "rinse" the heating delay light on the door comes on and the timer stops. The heater is still on (120volts) nothing further happens it just boils away on the water in the washer. Note: If I manually forward the timer to "rinse" the motor will kick in and run but does not pump out w


Most common d/w power is 120 volts, check for 120 volts with a  ... Dishwashers

I have a Vikin Dishwasher Model DFUD042 and the arms are not circulating water. When we start a cycle it drains previous water then fills it up after that it runs thought its regular cycle but the arms are not circulating water we have tried cleaning drain checked lines etc. still wont work.


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers

Something is causing the DW motor not to fire (so water is not sprayed around). It fills fine. It drains fine. I've tested the motor - it also works. I've tried all the various cycle choices; all do the same thing. Water fills but is not pushed around the tub (absolutely no motion from the motor, whatsoever). There was some debri down in the bottom, but I've cleaned it all out, wiped everything clean, and still no motor activation.


Clean pump and spray arm holes and any filters...you may need a pump kit if you see damage in your pump ... Dishwashers

Miele g892 scu plus, about 5 years old. when on, all it does is run some motor (humming sound) and flash salt or intake/drain. No program lights on. Sometimes can be reset so rinse light comes on and nothing blinks, but humming motor still runs and salt eventually blinks. I removed toekick panel; there is water in pan. I disconnect drain hose, only a little water came out. Any ideas?


... Miele G892SC SS Dishwasher

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

Water problem Hi, I have a Jenn air DW 711 that does not get water. I checked the following: Water line: I unhooked the water line and it is clear & free flowing. Float: The float moves up and down as it should. Filter: The filter inside the tub is clean. The motor runs and will drain any water in the tub I put a bucket of water in the tub and the dishwasher immediately drains no matter which setting I choose. Any ideas? Thanks, Steve


Many dishwashers will drain at the beginning of any cycle. \015\012If the water does not fill after the pump-out cycle, then the problem is either the fill valve or the float switch. You should be able to hear the float switch click as you rais ... Dishwashers

Kenmore Ultra Wash Quiet Guard - will not drain at end of cycle. After cycle is complete, water (not clean) sits at the bottom of the washer but I still unload the dishes and then turn the cycle dial around again - going past all the water heating and filling and washing - and land on the drain cycle, it will drain. Any ideas why it will not drain when I let a cycle run, but will drain once I cycle it through to the drain option?


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers

My fisher paykel DD603 fills with water at the start of the cycle and stops with the following error code and a beeping noise: - error U1 spanner symbol - crossed out faucet symbol. The water level is high enough that the spray arm is floating in the water. I am able to drain the water by entering the hardware diagnostics mode and running the motor in the drain direction. By removing the filter plate and examining the impellers I am not able to see visible damage. All filters are clean. The


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. You are spot on as error U1\015\012indicates that the dishwasher has twice tried to fill with the required amou ... Dishwashers

Kenmore dishwasher 587.15163401 won't fill. I checked the float switch with my multimeter and it's working properly. It's registering zero when I touch the terminals and 1 when I activate the switch. On this particular washer, how do I access the water inlet valve to check it for debris and also to check the solenoids? Also on this particular washer, how do I access the drain valve and solenoid. Can you tell me if this is a single direction motor or reversing motor. As I understand


The problem was the water fill valve. When set to Ohms, the multimeter never would read zero indicating a problem with the water fill valve. I replaced the part and it works now. Be sure to turn your water off under the sink before taking it off t ... Dishwashers

My dishwasher will not drain after cycling. I have check the drain hose connected to the disposal. All is in good order the hose is not cinked and the air hole is unblocked. I have also checked the screen at the bottom of the dishwasher, there is no debris or blockage here either. I can run the dishwasher on normal, it cycles but I still have stagnat water left beneath the bottom rack. How do I check my pump to see if it is working or could it be a short of some kind? It is a Kenmore Quite


The problem is a solenoid under the unit. It is a small black cylinder that operates a valve to change from the wash cycle to the drain cycle. You can probably order a new one from Kenmore for pretty cheap. ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

Mod #: MDB6600AWB Ser #: 16505148CG No water comes out of spray arms, checked and cleaned filter-OK. Wash impeller is cracked where it slides onto the hexagon rod but it you take the filter flow plate off and put the impeller back on, when you put the unit on rinse only and quickly open the door you can see it is still turning and moving the water. The unit still fills and drains. it just does not have enough force with the impeller to force the water into the spray arms.


Hi,\015\012 \015\012Please check the bellow link regarding your query....\015\012 \015\012 ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

Got a lound buzz type noise that I thought was a bad solenoid on the water valve. Tub also filled up & overflowed1 Replaced water valve ($30), but now dishwasher wont run thru cycles or fill with water to wash--seems to be stuck on drain even though digital counter counts down. What should I check next?


You may have dislocated the connection that controls the AquaStop circuit.\015\012\015\012This is linked to the inlet hose. Either the connector linking the inlet tap to the inlet valve is loose or the float switch has triggered.\01 ... Bosch 24 in. SHU53 Built-in Dishwasher

Frigidaire Dishwasher I have a frigidaire dishwasher that won't drain. it run through the entire cycle, the dishes are clean but the dishwasher is filled with the dirty water. I have unhooked the hose and let the water drain out that way but when i connect evrything back it still doesn't drain.


A common problem with dishwashers is the non-draining machine. If you are having trouble, check to see if the drainpipe and sink trap are clogged. If you still have drainage problems after doing this, check your drain hose to make sure there are no k ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

Dishwasher cycles with timer, won't fill with water. Motor runs fine, drain and fill valves test fine, float switch tests fine too. Water pressure fine. I'm thinking the timer is bad and won't send a signal to the water valve to open. What do you think? The system here doesn't know what a GSD2030F00WW is, so I had to pic one with a computer board, mine is not that sophisticated.


Remove the toekick plate on the bottom of the dishwasher.Remove the wires from the water valve. Insert the leads from a volt meter into the water valve power wires.Turn the washer on. After the initial pump out cycle the timer sends power ... GE 24 in. GSD2030Z Built-in Dishwasher

The dishwasher fills with water, but the motor just runs and doesn't clean the dishes or disperse the soap. It also drains the water. Wondering if the motor is burned?


DishwasherRepair Problem Detergent Cup does not Open\012heatman101 Asker's Testimonial "explanation very clear. will give it a go and see ... Kenmore Dishwashers

Dishwasher will not drain there is a bunch of water in the bottom. Tried running it through the cycle to make it drain out but still nothing just water in the bottom. Checked the sink and garbarge disposal to see if anything was blocking it or clogging it up but got nothing. Any suggestions?


Most likely a bad drain valve solenoid.\015\012It is attached to the side of the motor.\015\012The GE solenoids tend to burn out. ... GE Dishwashers

My Viking dishwasher won't fill with water. The motor seems to be running but no water enters the chamber. It's Sunday morning so I'm not able to get a repair person here. I got a response that said ''The ventilators are blocked. Turn it off and have the motor checked'' i was hoping for instructions on how to unblock the ventilators or clean it out. I have a house full of people for the weekend and would love to get this thing back up before Monday when a repair person could come. Any suggestion


... Viking Dishwashers

My kitchenaid KUDI01DL dishwasher began making a lot of noise while running, then subsequently decided not to circulate the water around to wash the dishes. It sounds like the motor is running (maybe) but there is no washing action going on. The machine will fill, drain and heat the water but nothing else. Is it likely that the pump/motor assembly has ceased to function properly? thanks...


The problem is very likely in the chopper and/or somewhat possible in the impeller. The chopper is replaceable from the front. Disassemble the pump, the chopper will be on its left side under a cover. That cover is kinda tricky to remove (remove all ... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1651 seconds