Having problems with your GE Adora GHDA654LBG Dishwasher ?

My dishwasher won't actually turn on this morning. When I push the start button, it hums, and the lights by the cycles flash, for about two minutes, but it won't actually run through a cycle.


Answers :

Your motor is probably stuck.
\015\012Remove power from the D/W.
\015\012Remove the lower access panel. The motor will be in front of you.
\015\012Turn the blades in the end of the motor counterclockwise until the motor turns freely. You will need a flat screwdriver to reach in and turn the blades.
\015\012When it frees, repower and try it again.
Repair Help & Product Troubleshooting for GE Adora GHDA654LBG Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dishwasher won't actually turn on this morning. When I push the start button, it hums, and the lights by the cycles flash, for about two minutes, but it won't actually run through a cycle.


Your motor is probably stuck.\015\012Remove power from the D/W.\015\012Remove the lower access panel. The motor will be in front of you.\015\012Turn the blades in the end of the motor counterclockwise until the motor turns freely. Y ... GE Adora GHDA654LBG Dishwasher

I have a Whirlpool GU2275XTVY0 when I start the cycle on normal it will run for about 5 minutes then the power button starts flashing and wont run. It drains fine and starts fine just wont finish the cycle.


It might help if the wash arm had started moving when it shut off.\015\012\015\012Unless it is always exactly 5 minutes I would say perhaps the door switch is out of alignment. It might start ok when you engaged at time of closing door bu ... Whirlpool Gold GU2275XTV Builtin Dishwasher

Cycle wont run and lights on main washes flash


What is the best way change heater parts to a BF 162 dishwasher is it difficult or can some one change if they have a good under standing of machine ... Hotpoint 23 in. BFI62 Built-in Dishwasher

My dishwasher is flashing the clean green light, however it shows it has 2 minutes remaining from previous cycle, i have let that 2 minutes run throught, but it then show up again as 2 minutes left, but still flashing clean, and i can not cancel to staret new wash cycle


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes 7 times, pauses, and then repeats. When\015\012the dishwasher doesn't sense a ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Kenmore elite 2 front loading washer model#110.45872400 It first flashed the code FH and then went to the running time is now flashing and it sounds like it is running but the cycle never starts and I cannot cancel the cycle by pressing pause/start two times. I have checked the water lines and the screens and cleaned out the drain catch below. what next


... Kenmore Dishwashers

My problem is with a Eurotech Model ED254EG timer will not continue running thru the cycle properly. i.e. In "Light Load" position the timer starts with 59 minutes but actuall runs for 2 1/2 to 3 hour


... EuroTech EDW242C Stainless Steel Built-in Dishwasher

The display keeps cycling thru some gibberish and wont run right. when i hitstart, it runs for the dislpayed 5 mins and counts down correctly, reaching "00" and then goes back to flashing gibberish. It will not let me chose a cycle on the inside either, as in "heavy", "fast"... please help


Not sure if you have fixed this problem yet. If it is happening only in one drawer then get a clean damp cloth and clean the key pad inside the top right of the door. Also clean the edges as well.\015\012\015\012If the other drawer is OK ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My Whirlpool ADP 5406 runs for about a minute and then the light flashes four times, repeatedly. What can I do to fix this? (I can still get the machine to run its cycle by holding down the start button, but the light will flash four times again on completion).


Hi and welcome to FixYa. I am Kelly. \012 Usually this symptom also shows an F7 error code. You will need to remove the lower wash arm (NOTE INSTALLED POSITION) Also you will need to remove the metal grate under the wash arm to ... Dishwashers

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

I have a Whirlpool ADP6515. It's been working fine for about 2 years now but recently cycles are not completing properly, it can run for 30-40 minutes depending upon cycle. The start light is flashing a 4 times repeatedly, I think this happens when it moves from a wash to a pump cycle but not sure. We have to hold down the start button to force it to go to the end of the cycle and the the lights stop. If we do that we can then use the dishwasher the next time, but only after we force it to go to


While replacing the console board, the replacement should be of same version. The boards are using programmable IC. Hence matching the software version is a must. Only the manufacturer or his authorized provider can help regarding t ... Whirlpool Gold 24 in BuiltIn Dishwasher w Adaptive Wash Cycle 24 in Builtin Dishwasher

Hobart LXIH won't complete delime cycle. Enters delime mode and executes the delime cycle properly until about a minute or so into the rinse phase. Machine shuts off abruptly with E5 code mostly, sometimes E4 code. Changed the control board, didn't solve the problem. The LXIH runs the normal wash/rinse cycle every time without any problems. This is a nearly new machine that actually don't need delimed, planning on selling it and it must work perfectly. I know some would program the delime notifi


... Hobart 24 in. LXIH-3 Built-in Dishwasher

Our GE Triton Dishwasher, mod# GSD5620D01BB is 10 years old. A problem started two days ago where; when it runs through a normal washing cycle; it contuously beeps about every 1 second when it reaches the Drying Cycle and the LED Green light flashes next to the Drying . I reset the breaker and tried again; same thing happened as it went through the normal cycle and when it reached the Drying part; same thing happened. The dishwasher is cleaning and everything else seems to be working fine.


The drying fan and vent system seems faulty.\015\012\015\012Refer this diagram. Item 918. ... Dishwashers

Matsui dishwasher Matsui MS452S slimline - second wash light flashing and unit doesn't fill. Tilting it backwards allows water to leak out from the left rear corner then it runs correctly for minute or two before numerous beeps sound and unit cuts out with light flashing again. How do I get into the base to see if there are any leaks? Unit less than 2 yrs old.


... Dishwashers

Hi I have a DS605SS Fisher & Paykel Single Drawer dishwasher, I rent the house and the landlord says that it is quite new can you please confirm the year? Also when we turn it on it runs for like 20 minutes then stops then when you try to start the cycle up again it stops after a minute and wont start again.


Heeeyyy - these have been around for ages no one can tell you the age unless you bought it and know where it was bought from to trace the serial numbers...\012\012I fail to understand why this is your problem when you are renting the hous ... Fisher and Paykel DS605SS Built-in Dishwasher

I have a Kenmore dishwasher model #17519200. I loaded it last night as usual and closed the door. I pressed the wash cycle I wanted and pressed the start button. I heard it starting to fill with water as usual. After it filled with water it should have gone into the wash cycle mode but it just started making a buzzing noise for about a minute or two then just stopped. I pressed cancel to drain it and it drains fine. I have kept trying to re-run it but it just does the same thing I described.


... Dishwashers

My daughter accidentally turned on our GE GLDA690 dishwasher. I can't seem to cancel it out without actually starting the cycle. I opened the door before the cycle started but now it is sitting there beeping. The obvious thing is to load it with dishes and run it. But it is just the two of us and we don't really have a load full. Owner's manual is no help. Even turning off the circuit breaker will not stop this infernal beeping. How do I cancel it? Why isn't there a cancel button?


... GE GLDA690MWW / GLDA690MBB Built-in Dishwasher

I have a Whirlpool model GU2400 Whirlpool Gold dishwasher and it will not start. There are no flashing lights just dashes across the time remaining box. I tried to push hi temp wash/heated dry 3x but it only allows me to hit it twice and displays 88 in the time remaining box. Then it says d3 in the time remaining box. It will then start running a drying cycle for 12 minutes. If I push cancel it won't do anything. I have to hold in cancel for about 30 seconds and it will drop down to 6 minut


... Whirlpool GU2400XTP Built-in Dishwasher

Just had new Frigidaire dishwasher installed. When cycle is started, display shows 99. Unit will fill with water, run cycle for about five minutes, stop and empty water then display a flashing PF. Can not seem to find a list of codes for this.


Pf is means power failure. ... Frigidaire 24 in. PLD3465REC Stainless Steel Built-in Dishwasher

Electrolux dishwasher all lights blinking and wont turn on push start button either all lights flash or normal light stays on  either case the dishwasher wont run a cycle


Remove the toe kick by loosening 2 screws. There is a panel there with little lights that correspond to specific problems. The light that is on will correspond to the problem that the dishwasher has detected. Correct the problem and you should be goo ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

Whirlpool gold, about 2 years old. the "clean" light is flashing. When I hit cancel, a 2 minute dry(?) cycle runs. The clean light resumes blinking. It will not start a new cycle


Looked in the manual and called a repairman ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Whirlpool model DU960 - from 2001, I think. Stopped running mid-cycle and the cycle lights flash. Won't run. How to fix? If I press 'Cancel/Drain', it flashes that button light. If I press one of the wash cycles again, it turns on the pump for about 1 second, shuts off and the lights flash again. I tried turning off the circuit breaker and turning it back on, but it still won't run. Is this fixable? Do I need to call for service? Or, would I be better off just replacing it?


I have a whilpool du960 the rinse only light is flashing and the light wash light is also flashing. ... Whirlpool Dishwashers

Dishwasher Power is on, lights on, wont start in any cycle. After several minutes all the lights flash continuously until power is turned off.


I removed the strainer to the water outlet in the bottom of the machine, cleaned it thoroughly, put it back together and it works fine!!\015\012\015\012Thanks for your service! Much appreciated.\015\012\015\012Cheers - Logan ... Dishwashers

Hi there...anyone home ??? My dishwasher is a Whirlpool Model # GU940SCGB2. What's happening is that when I start it. It'll start up run a minute or two....then it will stop. It repeats this all the way untill the end of the cycle and I end up with NO clean dishes and dishpan hands. Any ideas on what's wrong ???


Looks like micro-controller fault.You may have to replace this. Check with the manufacturer'sservice center. ... Dishwashers

It has been flashing an F2 error code and the timer starts at 65 then switches to "1" which stays on during the cycle. Now it will run for about a minute then stops completely. Can you suggest any parts that we can get to fix this?


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012\015\012The "F2" for Asko dishwashers indicates either the unit is overfilling, or the valve itself has failed.\ ... Asko 24 in. 1895 Built-in Dishwasher

I just bought a MDBTT53AWB1 dishwasher two weeks ago. The "clean" light is flashing eventhough I emptied the dishwasher and placed dirty dishes in. It will not allow me to run a new cycle. Can you help


... Maytag Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1721 seconds