Having problems with your GE Adora GHDA654LBG Dishwasher ?
I tried to run the dishwasher and it won't. It just says 1h on the display.
Error 1h means 1 hour delay and I don't think this is fault.\015\012To remove this error you can press and hold the AIR DRY/RINSE ONLY button for\015\01215 seconds or leave the unit unplugged for 1hour which will solve the issue. Hope\015\012this helps...please post back for further assistance.
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Hi I have a DS605SS Fisher & Paykel Single Drawer dishwasher, I rent the house and the landlord says that it is quite new can you please confirm the year? Also when we turn it on it runs for like 20 minutes then stops then when you try to start the cycle up again it stops after a minute and wont start again.
Heeeyyy - these have been around for ages no one can tell you the age unless you bought it and know where it was bought from to trace the serial numbers...\012\012I fail to understand why this is your problem when you are renting the hous ... Fisher and Paykel DS605SS Built-in Dishwasher
I have a Whirlpool model GU2400 Whirlpool Gold dishwasher and it will not start. There are no flashing lights just dashes across the time remaining box. I tried to push hi temp wash/heated dry 3x but it only allows me to hit it twice and displays 88 in the time remaining box. Then it says d3 in the time remaining box. It will then start running a drying cycle for 12 minutes. If I push cancel it won't do anything. I have to hold in cancel for about 30 seconds and it will drop down to 6 minut
... Whirlpool GU2400XTP Built-in Dishwasher
I tried to run the dishwasher and it won't. It just says 1h on the display.
Hi\015\012\015\012Error 1h means 1 hour delay and I don't think this is fault.\015\012To remove this error you can press and hold the AIR DRY/RINSE ONLY button for\015\01215 seconds or leave the unit unplugged for 1hour which will solve t ... GE Adora GHDA654LBG Dishwasher
I have a Bosch SHU5316UC dishwasher. The last two times it ran, my wife says the display said "CL" (for clean) after running through the cycle, but she heard a "motor running" until she opened the dishwasher. Attempting to run the dishwasher tonight, it won't start - it displays a "P" (error code?) when you attempt to start it. Can you tell me what the error code P is? Thanks, Dave
P stands for program in computer algorthms. The device displays program whenver chages were made to the default settings. A powered on devices least has malfunction only requires reseting to attaon default features. Depending on the type of device, r ... Bosch SHU5316UC Dishwasher
My brand new Samsung dishwasher today is displaying a 6E error message which my manual says is a functional error. It says to try to turn off the dishwasher and try to start it again. I seem to be unable to do this. HELP!
My dishwasher will not start. If you unplug it and plug it back in it says 1H, no matter what button you press it then says 2H and if you press another button it will say 3H until it runs through to 9H then will display --. It will continue to do this until you leave it alone and walk away. Then after a few moments it will clear itself out and the 'Normal' light under cycles will continue to blink. The dishwasher is 3 maybe 4 years old. Please help, I have a 3 year old and an 18 month o
Hi,There could be Few Possibilities.Let's try to Reset. 1h, 2H -----9H usually shows delay X hours Display where X would be 1,2...9.Turn the Power OFF for few minutes, say 5 Minutes and then Turn it ON. ... Dishwashers
Bosch Dishwasher SHV4313GB/17 Wont switch off ! The machine keeps running even when you open the door The pump is trying to drain water away (even though there is no water left in machine ) Have tried to reset it as instructed but to no avail. It has beeped like it has finished cycle but the pump wont switch off HELP PLEASE !
Introduction: This may work for your problem, but only if you're finding that you cannot get further water to flow into your machine. If your machine fills OK, then this ISN'T a solution to your problem. If your machine doesn't fill but your drain m ... Dishwashers
Gaggenau GM915-710 When I turn on the dishwasher, the display says 13 and the washer runs. But it run until the displays shows 1 and it is stuck there. I hear the machine going but it never stops.
... Gaggenau GI936-760 Dishwasher
Detergent cup Help!! I put jet dry dishwasher CLEANER in my jet dry dispenser. The bottle says "don't" and "make sure no dishes are in dishwasher". How can I clean it out? I've tried running it a million times, and pouring really hot water into it and still I get a murky backwash. I know it's all poisonous, but this stuff is scaring me out of using my dishwasher...
Take the front panel off and you will see the dispenser tank. Remove and clean. ... Bosch 24 in. SHY66C02 / SHY66C06 Built-in Dishwasher
I have a Siemens SE25A836GB/35 dishwasher. the program is running and it sounds as if the pump is running all the time. I have tried resetting the program but to no avail. I have checked the filter CLEAR and the water supply is okay. The display in the front which state time to run on the program is blank can you solve the problem?
... Siemens 24 in. SE25A836GB Hi-Line Free-standing Dishwasher
Have a Maytag dishwasher that will not run, display panel just has three blinking lights. Have turned off circuit breaker trying to reset dishwasher, to no avail. Still blinking.
Behind the lights and the control buttons there is a central control circuit board (known as the CCU), this board is going to need to be replaced, the part price depends on the model number of the dish washer, but on a ... Maytag Dishwashers
I have a Bosch SHU43C05UC diswasher. Last night, I put it on before going to bed as usual. I was awakened a couple of hours later to a loud grinding sound (like a pump being run dry), and found the noise coming from the dishwasher. The display read "0" time remaining, so I opened the door and the dishes seemed clean, so I left it shut off. Tonight I have been trying to troubleshoot the problem. The dishwasher will turn on, but it will not seem to fill with water. I have verified that the
Ok well before you can do anything you must obtain a service manual, link below.\015\012\015\012http://allrepairmanuals.com/bosch ... Dishwashers
BOSCH DISHWASHER QUIT MID CYCLE NO LIGHTS ON DISPLAY AND ACTS LIKE NO POWER. POWER INCOMING IS GOOD AND POWER TO SWITCH IS GOOD. TRIED NEW SWITCH WITH NO LUCK. MOTOR WILL RUN IF OVERFLOW FLOAT UNDER DISHWASHER IS LIFTED.
Check the sensor of the liquid at the bottom of the dishwasher. Sometimes that is the cause of the fault. ... Bosch SHU43C05 Stainless Steel Built-in Dishwasher
I have an Indesit IDL 735 model dishwasher. It wont drain the last bit of water and the first lgreen light is on when I try to start a cycle and it wont run. I think it may be some sort of block?
It is so common that the drain blocks in many ways and is the most problematic fault in a dish washing machine due to waste food particles. In all occasions it is important that your observation is most important and so is vital to the ident ... Indesit Dishwashers
My dishwasher adp 7570 is only four months old, but it do not clean the dishes properly. I tried to rinse it with sun rinse for dishwashers, but now it wont work. The start lamp blinks, and the display shows F2. The salt lamp lihts red.
I have had a repairman come out and look at this and he says all the diagnostic test say everything is okay. My problem: my dishes come out dripping wet...like it hasnt dried anything. Sometimes dishes are still dirty. I don't think there is any heat getting to anything. I run the water in the sink beforehand to try to get the water hot. I used this dishwasher for 1-1/2 years with no problems and now I have this problem. What is going on?
I am having the same problem but do not see any posted solutions. Have you solved this problem? ... LG LDS4821ST Stainless Steel 24 in. Built-in Dishwasher
Miele G842SC - opened the door while the dishwasher was running, the washer kept running and when I shut the door it stopped working. I have un-plugged the power and tryed to re-start but no luck. The Canada center says it is going to be 2 week for a repair and I have to wait to the day of to find out when the repair person is going to be there. I cannot believe the lack of service and support for this product.
... Miele Dishwashers
Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.
U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher
The display panel displays random numbers and jumps around... When I start the dishwasher the front panel say: 180, then 67, then 39, then 69..68. 69. 66. 37. 180...etc... It seems to be running though... totally weird. The Control Board has NO error code. I replaced the Control Board. Didn't fix it.
... Electrolux Dishwashers
Hi! My Bosch dishwasher (SHE46C02UC/22) will not shut off. The display says "1" - like there is 1 minute left, but it will not stop. Yesterday morning I started the dishwasher at 7:30am and at 11:30am I realized that it was still running. I opened it and it still had soapy water on the dishes and had not cleaned the dishes well. Any ideas?
Kenmore dishwasher my dishwasher was having a control borad problem, but we fixed that but the key pushing, but now when i try and run it the motor wont work
Whatlight are on ?does waterneter and then just quit? do you hear the motor humming? ... Dishwashers
My smeg dwi 710 dishwasher keeps flashing on the diplay panel and won't change to another wash selection. it wont close and wont start. the light is stuck on the heaviest wash selection and just keeps flashing on and off and on and off. i have tried turning it off, keeping buttons held down and nothing seems to work. there is nothing in the manual that says what the flashing means so i dont know how to fix it.
... Smeg Dishwashers
I have a LG intello dishwasher 2050SH Turned it on yesterday and did a rinse. This was the first use for 4 months in our second home. It was very cold. The rinse stopped some way through and an error message displayed (cannot remember). Tried to run again and now the dsiplay is locked. It turns on with usual sound, but none of the buttons work. They make a noise when pressed but nothing on the dsipay changes. I suspect that the outlet was frozen and that I should not have tried again - too im
Hi\015\012\015\012To\015\012unlock the lock in your LG Dishwasher, with the door open press the SPRAY &\015\012RINSE buttons simultaneously for 15 seconds. Hope this helps...please post back fo ... Dishwashers
Obtained this haier hdp18pa portable dishwasher, thought I would give it a try. The unit will not fill with water, turn the power on you can hear the motor or the pump running but no water comes in. THe 4 display lights flash and beep a series of times and then stop only to repeat the sound off in a every few second sequence. I have tried the remedies offered online, tilting the unit does not seem to work for me on this one. I changed out the water inlet valve but nothing changed and I got the s
HiYou need to clean the filter that is in the tube that gets water in the dishwasherin case you can not find it pls ask me to send you a diagram ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher
The display says oversudsing but there is no suds run the dishwasher with no detergent same error
... Kenmore Dishwashers