Having problems with your GE Dishwashers ?

GE Dishwasher that will not advance cycles

\015 I have a GE Dishwasher that will not advance cycles. Upon starting, it sounds as if it's going to do something, but just sits there humming and does not fill with water, however there is some stagnant water at the bottom neare the drain. If I manually change it to another cycle still nothing happens. Any ideas on what is causing this and how to repair it? Thanks!\015

Answers :

Sounds like inlet valve is not opening or water has been turned off or kinked.
Repair Help & Product Troubleshooting for GE Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!!


The Timer might not be bad. If one of the two thermostats is bad, the Dishwasher will exibit the same symptom. The thermostats are 141 deg. F and 161 deg F.They only cost $20 each. The Control Module is close to $200. ... Bosch SHU4006 Dishwasher

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!! I have the same problem. I took out the timer control and spraid it with contact clean


If the cycle doesn't complete, check these:Water-heating cycle ... Bosch SHU4006 Dishwasher

I have an old (not sure what year, 80s?) Kitchen Aid energy saver V Custom by Hobart dishwasher. We opened the dishwasher in the middle of a cycle and now cannot get it to re-start. When we lock it back up and push our normal buttons (Low Energy and Energy Saver/Dry Heat Off) or any other combination of buttons, the dial does not turn automatically and the cycle does not continue. I have also tried advancing the dial manually and still, nothing happens. I have even tried advancing it all the


... KitchenAid Dishwashers

I have a Jade RJDW2470A dishwasher which was re-branded Jade. (It is a Maytag product.) It get's stuck between cycles and will run forever unless I manually advance the dial to the next cycle. It seems to get stuck around the "rinse" cycle and the soap door does not open until after I advance it past that cycle.


... Jade RJDW2470A Free-standing Dishwasher

Hi - i have a Turbo dishwasher (made in Italy). It has a foul smell when you open the door, i ran an dishwasher cleaner through it on an emply cycle last week, was good after that, now stinks again. also the dishes are not drying properly, and when the cycle is finished, the dishwasher has lots of condensation inside. Thanks in advance.


Your heater system has stopped functioning.If you have a heated dry setting use it.If it does not work you will have to repair the heat system. ... Dishwashers

Kenmore dishwasher. The upper rack is not getting clean. Even very light residue remains. And, detergent is left in door at end of cycle. The bottom is filling up, so I don't think it's the intake valve. Also, all the blade openings appear clear. I am noticing that hot water is not filling the dishwasher when I first run the cycle. Even if I have hot water running in the sink, the dishwasher fills with cold or warm water. So, I think this is the problem. What should I do? Thank you in advance!


I find it odd that the dishwasher is filling with cold water if the water is hot at the sink. It sounds like the dishwasher is connected to the cold water line rather than the hot. Check under your sink; if you've got standard plumbing, the dishwas ... Dishwashers

Dear sir In an attempt to dislodge a blockage of my sewer line using Draino and a plunger some of the Drano ended up in the dishwasher and now the dishwasher will not run. My dishwasher is a SHU3036UC/U12. When starting the unit up it empties the unit but the cycle newer ends, in other words the timer does not advance to the next cycle, I have determined that the timer motor works by removing it from the unit and supplying it with power. One thought is, can the water level switch be stuck in


HiCheck this video and clean the drain pump assembly: ... Bosch SHU3036UC Dishwasher

I have a 1999 bosch SHU 4300 dishwasher given to me. It worked great for about two weeks. Now it takes for ever *3-4 hours* to complete a cycle (if it does). I have opened the door to see it filled with sudsy soap after this long. I have checked the hoses and they are not kinked. Once the cycle of cleaning is over, If I reset it manually, it will rinse the dishes and empty just fine. But I have to manually get the dishwasher to advance to the rinse and dry cycle every time now.


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch 24 in. SHU43 Built-in Dishwasher

All of a sudden, my Kenmore dishwasher (Model 363.1411691) will not cycle. When I lock it shut and try to set it to wash, all I hear is a click--no motor running, no water sounds. As I advance the timer knob, I just get clicks where each cycle should begin. There is standing water in the bottom of the dishwasher which does not drain out. Any advice would be much appreciated, for sure.


Hi.The clicks are simply the relays in the timer board that try switching on. The control module is likely working.The cycle does not start because of a different problem.If no light is coming on, then ensure that wall socket ... Dishwashers

LIGHTS FLASH Hallo, I have a Indesit dishwasher (IDL 750) and the last few weeks there is a malfunction. After 15 minutes that the wash cycle 2) had started the dishwasher stops and the first and third wash cycle phase indicator lights flash, beginning from the right. Could you help me telling me the possible cause of this malfunction. Thank you in advance Fred Tourman Athens, Greece


... Dishwashers

Miele 868 dishwasher-water fills at begin of cycle,but pump/wash cycle doesn't engage(timer dial still advances,drains at end of cycle.dishwasher was workong,but was moved to a new location ans hasn't worked since.impeller moves freely and pump was rotated via 8mm hex key.is there possibly a reboot/reset, or is there possibly a water pressure issue?-I didn't think so as the dishwasher fills to the prescribed level.


... Miele Dishwashers

My Dishwasher (Westinghouse907 series) will not advance past the prewash/rinse cycle. I have cleaned out the filters. I also turned it off for a while and when I turned it back on it worked, but has now gone back to not advancing past the first step in the cycle.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. If the cycle doesn't\015\012complete, then the first thing ... Westinghouse 24 in. MDP531 RF Free-standing Dishwasher

My dishwasher is a Fridigdaire FDB510LCS1, approximately five years old. The timer/knob stops advancing at about 7 o'clock, somewhere in the wash cycle. But the washer keeps running. I marked the place where it stops and, on additional tests, it stops in exactly the same place. I can advance the knob slightly past this location and the washer continues through to the end of the cycle.


Hi\015\012\015\012This is due to a faulty timer on your dishwasher. You would need to replace it to resolve this issue. You can buy the timer for your dishwasher from this link---\015\012\015\012 ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

I have a Bosh SHU3302UC dishwasher that seems to be pumping all of the water out of the basin and will not advance to the next cycle. I know it is normal for the washer to pump to the drain at the beginning of the cycle, but this unit will not advance. Any thoughts??? Thank you, Matt


Make sure you go to the Bosch website and follow the recall notice on this model...they have a recall repair notice that replaces the faulty controller on this model...the faulty controller may cause a fire so be sure to stop using the unit until you ... Bosch 23 in. SHU3302UC Built-in Dishwasher

I cannot figure out how to advance a cycle without having to go through the entire cycle. For example, I had a drain problem with my sink and the plumber put the rinse and hold cycle on for about 10 minutes; now every time I want to turn on the dishwasher it is in the rinse and hold cycle. How can I change it???


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Your post doesn`t specify a model number, however on most Bosch dishwashers in order to change from "rinse & hold" to "regular" ( or any cycle ) simply turn t ... Bosch Dishwashers

Bosch dishwasher won't advance through wash cycle automatically


... Bosch Dishwashers

Dishwasher during normal cycle gets hung up and does not advance


HI. this is just a control fault. you can try to reset the core program by unplugging this unit for 5 minutes. this will drain all power and reset the core on the timer/control.If you experience the same situation after this reset, simply ... Kenmore Dishwashers

Hello, my Hoover D7610 dishwasher has developed a problem, I would appreciate your advice.On starting a wash it appears to be working OK through what I believe to be a rinse cycle but then after about 20 minutes water pours out from the bottom of the door. Manually clicking the timer-programer forward stops the leaking but the machine needs manual advancement except for the last 2 cycles when the timer seems to work OK. After the 1st cycle there is no more water leaking from the machine but all


... Hoover Dishwashers

Whirlpool dishwasher model DUB700XB has quit cycling. Fills with water but will not start wash cycle. Making intermittent humming noise unless the door is open to disengage the switch, even when on stop. No LEDs lighting when rotating the dial through the various cycles. Unit is old and wondering if it's better to buy a new one rather than fix this and have something else go wrong in the not to distant future. Thanks in advance


... Dishwashers

Long cycles My dishwasher (approx 7 years old) will run in the wash cycle for hours...until I physically turn the nob to "rinse"; then it will stay in that cycle until I advance the knob to the final (expel water) stage. I checked the filter and the blades - no obstructions. Also, when completed, the dishes are hot, so I know the heating element is working.


Http://www.thisoldappliance.com/library/bosch_dw_guide.pdf\012\012\012 ... Bosch 24 in. SHU43 Built-in Dishwasher

Hi There, I have a Zanussi dishwasher ZDT 6252 that doesn't clean my dishes properly. Cups/glasses on the top tray get residue left on them if the dishwasher is anyway full or potatoes are on the plates (even after rinsing plates). Can you please recommend what i need to do? I have ran a dishwasher cleaner through on hot cycle. Many thanks in advance. Patricia


... Zanussi 23 in. ZDT6252 Built-in Dishwasher

KitchenAid KUDP01DLBS2 dishwasher. Runs for a very long time on any cycle; time does not seem to advance. (takes 2.5 hours or more for normal cycle. "sensing soak", "water heating" lights on for a long time, even though it appears that water is not being heated. Checked incoming water temp, is hot. Did not do this when new, something has changed. Typical cycle was 1 hr 10 min. before.


Sounds like the heater inside the dishwasher is not working. The machine is trying to get the water up to a preset temperature, probably in the neighborhood of 140 degrees. That is one of the things that it is sensing.After the machine fi ... Dishwashers

My Bosch SMU2000 series dishwasher will not complete the wash cycle. Advancing the dial completes the cycle but it sticks again before completing the rinse cycle. I replaced the timer assembly and the symptoms are the same


Hi,It seems to me a Faulty Control Board. You need to pull up the control board and check the resistors on it. If found burned or swelled, needs to replace those.Note - It's better to replace control board than to repair as yo ... Dishwashers

Bosch Dishwasher SHU5312UC-cycle not advancing.


... Dishwashers

GE Dishwasher that will not advance cycles


Sounds like inlet valve is not opening or water has been turned off or kinked. ... GE Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1675 seconds