Having problems with your GE Dishwashers ?

We have a GE Profile Dishwasher Model GSD4430X66WW. It runs through the all cycles but at the end displays code PF and there is a couple of inches of water left in the bottom. If I hit the run cycle and then the reset, the water will drain and the code goes away. Any suggestions?


Answers :

Pf means power failure. you may have a loose connection underneath where main wiring ties in in box.
Repair Help & Product Troubleshooting for GE Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a GE Profile Dishwasher Model GSD4430X66WW. It runs through the all cycles but at the end displays code PF and there is a couple of inches of water left in the bottom. If I hit the run cycle and then the reset, the water will drain and the code goes away. Any suggestions?


Pf means power failure. you may have a loose connection underneath where main wiring ties in in box. ... GE Dishwashers

We just purchased a used Fisher and Paykel DS 603-i. After installing and running the normal cycle there was a lot of water left on the bottom of each drawer. We ran the bottom drawer (water stil siiting on the bottom of the top drawer) and part way through the main wash cycle we got what I think was a F1 error code (we do not have the LCD version but the Rinse light was activated). I took out the bottom drawer, dried out the basin and then took out the washer and reattached the drainage pipes t


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You’ll need to reset it by poweri ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

Model#lds5811bb--started making noise coming from the water inlet area(bottom left). 3/4's of the way through the cycle, noise became louder and then an error code "le" came on. We tried turning breaker off, then we tried in the rinse only cycle, but 5 minutes into it the "le" code error came on again. I'm fairly handy, so I'm not sure what part I can replace to maybe solve the problem. I can't afford to spend a couple of hundred dollars for a repair man to fix it. I'll appreciate any suggestion


The LE code is a locked motor code. Something may have gotten into the pump impeller. I would take the screens and filters off and clean the and check the pump for something stuck in it. It could also be the motor going bad but I would check the obvi ... LG Dishwashers

We have a +11 year old Bosch SHU3006/UC/U06 that never leaves the wash cycle. We had to stop it during our last test run at 3 hours. Chat advise is suggesting a water temperature problem (I origionall thought the timer), suggesting that the cycle will not advance until it hits a set temperature (170 degrees). We checked and noticed that the water in the machine was only around 90 degrees during a wash cycle. We do not have exploded views or parts drawings, nor electrical schematics. I wou


Check continuity of the heating element to see if it is broken/open.\015\012\015\012The dishwasher prefers that the incoming water (water heater) be 120 degrees (F) ... Bosch SHU3036UC Dishwasher

Dish washer does not drain after the cycle is complete. The last few months when the dishwasher is done their would be a small amount of water left in the bottom. It didnt create any problems but would smell after a few days. So we would just run the drain cycle and it would empty. Well i got home to and the wife said the it was really full. The water was dirty and when you run the drain cycle it didnt drain. She said the dishes were clean. So i cleaned the vent, and filled the sink with


Check drain hose and drain pump.End of drain hose must be in same level with machine.Try it. ... KitchenAid KUDR01TJ Dishwasher

Kenmore dishwasher. The upper rack is not getting clean. Even very light residue remains. And, detergent is left in door at end of cycle. The bottom is filling up, so I don't think it's the intake valve. Also, all the blade openings appear clear. I am noticing that hot water is not filling the dishwasher when I first run the cycle. Even if I have hot water running in the sink, the dishwasher fills with cold or warm water. So, I think this is the problem. What should I do? Thank you in advance!


I find it odd that the dishwasher is filling with cold water if the water is hot at the sink. It sounds like the dishwasher is connected to the cold water line rather than the hot. Check under your sink; if you've got standard plumbing, the dishwas ... Dishwashers

I have a brand new whirlpool DU1055XTV5 dishwasher, installed two days ago. After the cycle completes there is about 1/2" clean standing water left in the bottom. It is not just down in the well area, the whole bottom is covered with water. This is after running a normal cycle with no other options such as sanitize or heat dry. I called Lowes, the store that sold/installed it, and they said this is normal in new dishwashers to keep the parts wet. They said as long as the water does reach th


... Whirlpool DU1055XTS Built-in Dishwasher

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

My bottom dish washer was draining the water on the top dishwasher and there is always water left over on the top.I remove the pipes and put CLR to clean up drain.Start both dishwasher on rinse cycle ( 12 min cycle) then at 10 min.they start blinking with a No tap (may be water ) sign on it. I run the cycle again now a F1 sign coming with a tool sign.And both dishwasher going crazy ,it turn on by itself even I powered them off.


Hi\015\012\015\012\015\012Thanks for using FixYa. F1\015\012error means that the flood switch has been activated. You'll need to reset it by poweri ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th


... Maytag Dishwashers

The top drawer on our dishdrawers makes a clicking kind of noise for about the first 2 - 5 mins of being on. Then goes fine with the occassional clicking noise during the cycle. It is slightly noisier than the bottom drawer. When the cycle is finished there is a couple of inches of water left in the bottom, so the dishes don't dry properly. The bottom drawer works really well with no problems at all. What do you suggest?


... Fisher and Paykel DS605I Built-in Dishwasher

There isabout 2 inches of water left in the bottom of the dishwasher after i run a cycle , and some food bits left in the water how do i drain the waterand remove the food bits? A manual was never left when the new machine was installed. We have a Quiet something 3 machine.


The filter is probably blocked.\015\012\015\012It is inside the base of the machine.\015\012\015\012Take out the filter and clean it and also clean out the filter well as that can also hold quite a bit of debris.\015\012\015\012 ... GE Dishwashers

Dishwasher will not drain there is a bunch of water in the bottom. Tried running it through the cycle to make it drain out but still nothing just water in the bottom. Checked the sink and garbarge disposal to see if anything was blocking it or clogging it up but got nothing. Any suggestions?


Most likely a bad drain valve solenoid.\015\012It is attached to the side of the motor.\015\012The GE solenoids tend to burn out. ... GE Dishwashers

Kude48fxbl - brand new out-of-the-box. When put through a test cycle after installing it, water poured out of the bottom left edge of the door. This was not associated with either the water input or the discharge hose, but rather seemed to come from the interior of the washer and out under the door. The door seemed well latched, and running it with some dishes in the bottom tray (not blocking the soap dispenser) didn't help.


... KitchenAid Dishwashers

Dishwasher runs thru cycles and water is left in bottom after cycle is complete. dishs are not cleaned. while running it seems fine


Check the spray arms for proper seating.Clean the jet holes. Check the pump also. ... GE Dishwashers

My dishwasher will not drain after cycling. I have check the drain hose connected to the disposal. All is in good order the hose is not cinked and the air hole is unblocked. I have also checked the screen at the bottom of the dishwasher, there is no debris or blockage here either. I can run the dishwasher on normal, it cycles but I still have stagnat water left beneath the bottom rack. How do I check my pump to see if it is working or could it be a short of some kind? It is a Kenmore Quite


The problem is a solenoid under the unit. It is a small black cylinder that operates a valve to change from the wash cycle to the drain cycle. You can probably order a new one from Kenmore for pretty cheap. ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

The dishwasher top drawer is leaking all over the floor during the cycle. When the top drawer is running, It fills up the the bottom of bottom drawer with water also and then neither drawer drains completely. The water is a light brown color after a wash and often half the soap is left in the dispenser.


Fisher and Paykel design a air gap kit to prevent the water back flowing to the other while one is running. it really works and worth of your money.\015\012You need to change the lid seal and a pair of actuators from the top drawer. Because of the ... Fisher and Paykel DD605SS Stainless Steel Dishwasher

Bosch shx dishwasher that leaks from the bottom. When I hit the cancel and drain it drains just fine. I have taken off the front of the door and see the water starting to overflow on the front tray when I run the cycle. Before it starts to overflow I hit the cancel drain and the water does drain


... Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

When I start the top drawer it defaults to 5 minutes (with the lights Heavy, Fast, Rinse highlighted) runs for a couple minutes, then stops and the LED starts randomly cycling through all kinds of codes very quickly. There is water in the tub that has not drained after completing the couple minutes of operation. This cycle repeats itself if I hit the power button again after the LED starts freaking out. The 5 min cycle shows in the LED, sometimes with the no circulation error, sometimes with the


Here is the solution: \015\012http://applianceguru.com/forum1/24814.html ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Fisher paykel Hi I have a fisher paykel dd603 dishwasher. when I run the bottom drawer on its own ,,it also fill the top drawer with water ! so after the dishwashing cycle , im left with water in the top drawer. im guessing that a valve should close on the top drawer to stop this happening? is there a part I could order and replace myself? thanks [email protected]


Check your email ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

Its a GE dishwasher and water is left in the bottom of the dishwasher. I have run it through its cycle twicw it sprays water around in the dishwasher but doesnot want to drain.


There is a solenoid valve located near the motor which should activate to either drain or to spray. These often get jammed up with food particles. Locate it and take it apart. Clean out what ails it and put it back in service. ... Dishwashers

It went thru the whole cycle and when I opened it up - there was water still left in the bottom - hit the cancel/drain button and nothing happened. Unhooked the drain line to the drain pipe under the sink and no water came out. How do I find out if it is the pump ? If I take it out - what do I need to look for and what trouble shoot things do I need to know. I live about one hour from the nearest town - so I would like to find out the problem - before I call a repairman and maybe fix it myse


... Kenmore 24 in. 17462 / 17464 / 17469 Built-in Dishwasher

We have a Kenmore dishwasher, model #665-15955793, that is not draining properly. After running through the cycles there is water still left in the bottom of the dishwasher and the dishes have water spots. Is the problem with the line to the garage disposal?


... Kenmore 24 in. 16032 Built-in Dishwasher

Towards end of dishwashing cycle error code comes up and consitently beeps, can not turn off by machine buttons or reset. We have to reset by power plug. Water is left in bottom of macine, dishwashing powder is left on most things. Rinse button then works, it then drains the machine no problem. So I dont think it is the pump.


No response ... Dishwashers

My Whirlpool dishwasher ADP951 does not start at ll. I think I turned off the machine last time before it completed its cycle. I found there was water left at the bottom unlike after a usual run. I manually removed all the water and mopped it all. yet it would not start at all as if no electricity comes into the dishwasher. Please help.


If your dishwasher is on a wall switch, someone may have shut it off, Your dishwasher could be pluged into a Daisy chaned GFI, check all your GFI in the kitchen and make sure none are triped. The home Fuse Box, make sure the braker is not triped. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1813 seconds