Having problems with your GE Dishwashers ?

I have a Triton dishwasher. Last cycle, it completed washing then started drying and started beeping and the drying light is flashing. When I finally opened the latch, the beeping stopped, but the drying light is still flashing. The dishes were clean and warm - they air dried the rest of the way. I have not been able to get the drying light to go off. I have turned the breaker off over night, and flipped back on. The dishwasher goes back to flashing washing, and then clicks to drying and th


Answers :

Hi,
\015\012Make sure the salt level is ok - add 1Kg of salt if you have not done it in a while, and check rinse-aid level if apliccable.
\015\012
\015\012If this does nothing, then remove the lower kick panel for access to a data sheet which should be in there on the right hand side.
\015\012This lists error codes for your model.
\015\012While you are looking in there - check there is no water in the flood sensor. It's basically a float in a tray. If there is water in the tray, empty it and see if the error is removed.
\015\012
\015\012Finding a possible leak is another matter of just watching while running a cycle.
Repair Help & Product Troubleshooting for GE Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Triton dishwasher. Last cycle, it completed washing then started drying and started beeping and the drying light is flashing. When I finally opened the latch, the beeping stopped, but the drying light is still flashing. The dishes were clean and warm - they air dried the rest of the way. I have not been able to get the drying light to go off. I have turned the breaker off over night, and flipped back on. The dishwasher goes back to flashing washing, and then clicks to drying and th


Hi,\015\012Make sure the salt level is ok - add 1Kg of salt if you have not done it in a while, and check rinse-aid level if apliccable.\015\012\015\012If this does nothing, then remove the lower kick panel for access to a data shee ... GE Dishwashers

Maytag MDB 8600 AWB dishwasher Wouldn''t start... just a Heated Dry light. Replaced (already broken) door handle with complete latch assembly. Still, Heated Dry flashes. Tried various suggested combos of 5 or 6 quick button pushes followed by Start. Only get a 50-=countdown that repeats endlessly. Sometimes alternates with the letter L. Once by luck I guess it went into Heavy Wash mode, or at least the diagnostic for it. Completed this fine, then back to the stubborn Heated Dry light.


... Maytag 24 in. MDB8600AW Jetclean II Built-in Dishwasher

I have a General Electric pdw7880J03ss dishwasher. Tonight, I went to start a load of dishes and the Heated Dry option wouldn't turn off without the lights going to RINSE ONLY. Then the 1hr setting started coming on. Then was able to get the load to start but then it stopped somewhere in the cycle. Now, no lights will come on the panel though I can hear the beeping. Dishes appear to have washed...


Hi\015\012\015\012Press and hold the heated dry button for 15 seconds to reset\015\012the control, if this wont work then it means that the control board is bad and\015\012should be replaced. Hope this helps...please post back for further ... Dishwashers

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

My smeg dishwasher seems to be permanently in wash mode. The light on the menu of settings no longer flashes, but permanently is on, and when I run a load it never stops. I hear the two beeps as if the dishwasher is starting a load so it seems to be cycling through over and over. How can I fix this and get the blinking light back? Thanks


You have a timer relay issue ,probable need a new board for it ,a cheap fix would be to time it and see how long it take to run full cycle and put a regulaer outlet timer on it or a alarm off your stove or what ever,save a couple of bucks ... Smeg STX2 Dishwashers

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

The GE Profile Dishwasher will not allow me to start without the heated drying light coming on. I want to wash without this headed drying at the end of the wash. When I try to turn it off it turns the start cycle off. This happend over and over again when I want to turn on the machine, It finally lets me get an unheated dry wash started to complete. A problem every night. PDW7800N15CC. Serial MM8243388


... GE 24 in. Profile PDW9800J Built-in Dishwasher

Replaced circuit board on my kenmore 665.13742k603 dishwasher,still all wash buttons,and start button will do nothing.ran test using sani rinse and heated dry buttons all lights come on but washing light does not,all lights remain on after test,unplugged,plugged back in,,still no wash buttons or start buttons work,can you help?


... Dishwashers

I have a Whirlpool Gu180 ESJQ with a blinking green start light. If I clear this light (hold the start button for 5 second to place it in the end of cycle) then I can get it to start another wash cycle. However, the next wash cycle ends with a blinking start button again and the dishes aren't dry. I had an appliance service man come to check it out and he could not detect any problem! Now I have a leak!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

My frigidaire dishwahser was set to run a normal wash cycle and heat dry. It never ran, the soap is still in the holder and the lock beneath the heat dry option is lit. I'm unable to cancel or select any other options. I cannot get the dishwasher to run. Do you have a solution? I have tried holding down a number of the buttons in different combonations but still can't get the light to go out or start a wash cycle.


Looks like a number of things are happening.\015\012\015\012It would be easier if you can provide the model no. of your frigidaire dishwasher.\015\012\015\012I am assuming you have turned the mains power off and on. ... Frigidaire Dishwashers

FDW60 Fault Hi, I have exactly the same problem. My dishwasher starts and washes ok but appears to get very hot during the drying phase and then the two lights fast and eco flash warning of a heater problem. I suspect either the heater, thermostat or control PCB. As the rest of the cycle seems of and the water gets hot then I'm assuming the heater and thermostat are OK. When the dishwasher attempts to dry is when the problem starts. Did anyone find out what there fault was? Thanks


Hold down the start key and you will re- set the D/W. Please Rate This !!! Thank YOU !!! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I have model GU3600XTSY2. Sometimes the pots and pans light flashes for no reason. Sometimes I can push that button and it stops. However, the cycle I select to wash the dishes is constantly interupted by the pots and pans (P&P) light flashing. If I push the P&P button, the wash cycle usually starts where it left off. Sometimes it will go back to the beginning of the cycle and begin all over again and get caught in a loop; start washer, P&P flashes, push P&P, begins cycle from beginning, P&


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

MY DISHWASHER MODEL GHDA480N10WW LIGHTS ARE FLASHING ON THE NORMAL WASH AND THE HEATED DRY I OPENED THE DOOR IN THE MIDDLE OF THE DRYING CYCLES THE LIGHTS STARTED TO FLASH AND BEEP I UNPLUG IT TO SEE IF I COULD RESET IT AND IT STILL BEEPS AND FLASHS


... Dishwashers

Hi just had new dishwasher put in its a diplomat intergrated dishwasher aca9102, only used it once and started beeping towards the end of the cycle. thought it might be coz i didn't put salt in it, and had tablets instead of detergent so put salt in and detergent in but couldn't get rinse aid. started the program on normal wash but started beeping 10 beeps straight away and the first three lights out of 6 are flashing on the control panel. could it be coz theres no rinse aid in it? please someon


Dear tracy83, \015\012\015\012we have an aca9102 diplomat dishwasher since april 08. we now have a fault with dishwasher but cannot locate our manual. could we arrange rto have a copy of your manual? sorry for being up front but cannot ob ... Dishwashers

Kenmore ultra wash quiet guard dishwasher, the pots and pans and the normal wash button are blinking. The start and cancel and smart wash out tons have a faint light glowing. Thoughts? I tried the sequence of pressing heated dry, normal wash, heated dry, normal wash and that did nothing. I've flipped the breaker too. I was in process of taking it apart to clean filter, thinking that would help, but lost my manual and now I can't get that off to flea either:(. Sig


... Kenmore 24 in. 15689 Built-in Dishwasher

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

We have a Kenmore Ultra wash dishwasher Model # 665.13733K601 and serial # FW18136133. came home from work yesterday and the pots and pan button and the normal wash buttons were flashing alternately. When I pushed the cancel button it started to flash, then I pressed the smart wash button and now its flashing. I turned of the breaker for awhile and then back on and the lights weren't on right away but later started flashing again, and I can't get the dishwasher to do anything. Any help on my pro


Hi,\015\012That unit took a power surge and the control is now bad....those controls can all of a sudden go wacky and the usual cause is power problems...\015\012The only way to fix it will be to replace the control...\015\012 ... Dishwashers

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

I have a Whirlpool Gold Quit Partner III, model GU1100XTLB1. When I run the normal cycle it functions well until near the end. At that time the unit stops and the pots&pans indicator light blinks. If I hold the cancel button in the unit drains then refills and the light starts to link again. I don't know how to reset this unit because I only have air dry. If I leave the power off for a day I can get the unit to reset. If not, it just fills back up with water and the pots&pans starts blinking aga


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a GE dishwasher with front control panel and at first the wash and dry lights stayed on and it was beeping every 30 sec. when I turned the breaker off for the required 30 sec. the lights started flashing and it is still beeping. The control panel seems to be frozen as it is not working and wont do anything.. everything was working fine before this. I bought it at Home Depot on 3/14/07 and had it installed by a licened electricion. Help


Call ge @ 800-386-1215 for service ... Dishwashers

Hi! We have a GE Profile PDW9280J0SS with electronic control malfunctions. I can't get it out of the ADDED HEAT mode and many of the other button lights won't light up. I've flipped the breaker several times, and this does (usually) reset the controls to "Normal" and "Heat Dry", but when you push "Start" it switches back to the ADDED HEAT mode. When it goes through this cycle the soap dispenser doesn't open so the dishes don't get clean. I can't use the arrows to select different types of w


Not a specific fix, but I can tell you I have this same exact model dishwasher, since 2005, and it has been services for touch pad button problems at least a dozen times. I am in fact on the phone now with service scheduling another visit because i ... Dishwashers

Normal Wash, Heated Dry, Hot Wash, and Hot Start lights all flash. Dishwasher will not do anything except beep every couple of minutes with these lights flashing.


... GE Dishwashers

My Maytag steam dishwasher # MDBH980AWS won't do anything when I hit the start/cancel button. Nothing happens no lights go on. When I his the cycle select button only a few of the lights go on - steam clean, High Temp wash & Sanitize. The heated dry button, or the Heavy, Normal, Light cycle buttons won't light up. How do I get it started?


My Maytag dishwasher # MDBH950AWW wont turn on no light but it has power in the outlet no power to the control board ... Maytag 24 in. MDBH950AW Built-in Dishwasher

Hi, we have a Hoover HEDS668-80 dishwasher at work. The first problem we had was none of the programs would run this turned out to be a broken door lock. After replacement we managed to get one pre wash and one wash program to run, now when we try it, it starts but after 2 minutes the pre-wash and wash lights flash and the machine beeps 8 times. Can anyone help?


... LG LDF6810 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1437 seconds