Having problems with your GE Dishwashers ?
Water is not spraying around and soapy water is in bottom after putting no soap for past five starts
You have an oversud problem and pump is cavitating due to too much soap. best and quickest way is to remedy is use 1 cup liquid fabric softener and let dish washer run thru complete cycle wit heat dry in off position.The fabric softener will break down the soap and remedy the problem. Hope this helps.
Repair Help & Product Troubleshooting for GE Dishwashers
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Water is not spraying around and soapy water is in bottom after putting no soap for past five starts
You have an oversud problem and pump is cavitating due to too much soap. best and quickest way is to remedy is use 1 cup liquid fabric softener and let dish washer run thru complete cycle wit heat dry in off position.The fabric softener will break do ... GE Dishwashers
Hi, I have a Fisher Paykel DD603I (integrated) dishdrawer unit. The bottom drawer soap dispenser has water in it after it runs (and leftover soap), and there is a small amount of water sitting in the bottom of the drawer. The dishes don't get totally clean. I have removed and cleaned the spray arm, drain filter, filter plate and bottom of tub. Found nothing clogged or particularly dirty. Put all the parts back in and everything moves freely. Ran it empty, and same problem occurred.
Hi Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doe ... Fisher and Paykel Dishwashers
I have a GE Triton XL dishwasher that is not spraying water onto the dishes. I just reset the power, and that didn't help. Putting it on the rinse only or wash cycle fills the bottom with water, but it sounds like a trickle vs. the spray. The heating element comes on and the soap door opens, but there's not spraying. I made sure there was nothing clogging the water line or other parts. What do you think is wrong?
... GE Tritonr XL GSD6260JCC Dishwasher
GE Nautilus My dishwasher is approx. 6 years old. It has recently started having this problem. On the second cycle (the one where the little door inside opens and release the soap) does not want to work right. The door will open, but it is like there is no water spraying to spread it out. The soap (I've tried both liquid and powder) sticks and drys, running down the door and in the bottom of the tray. I have to open the machine and add the soap to the bottom of the machine if I want to get my di
Smoking from GE (Model:gsd3725f00bb) dishwasherWe moved in an old house, the dishwasher had been installed. but today we found smoking from the dishwasher and smells burned plastic. Could you have any resolution for me? or this problem is popul ... GE Nautilus 24" Built-in Dishwasher
I have the GE Quiet Power 3 Model gld4400n10bb. When I start a wash I can hear it fill with water (to about 1/2 inch below the heating element). It then waits for about 5-7 minutes and pumps the water out. It fills again several times and pumps out. It doesn't sound like it is washing though. The whole interior of the dishwasher is covered with dried soap. I can also tell that water is not spraying around the whole interior. Any ideas?
... GE GLD4400NWW / GLD4400NBB / GLD4400NCC Dishwasher
New SHE4AM16UC, professionally installed eight months ago. Worked fine with very light usage until now. Dishwasher starts normally but stops and signals "clean" after less than five minutes on any cycle. One inch of water in bottom that (I think) drains when a new cycle starts. Soap tablets are not ejected from compartment. Bosch authorized repairman says he now has two client dishwashers with identical symptoms and is asking Bosch support for ideas (he's changed pump, control unit, and float sw
Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats.\015\012When the dishwasher doesn't sense a water t ... Bosch SHE4AM16UC 24 in. Built-in Dishwasher
The insultation on the bottom of the door is wet. My repairman said water is getting behind the soap dispenser and the rubber gasket around the dispenser is hard. The dishwasher is only 4 years old. Is this possible. The insulation at the bottom of the door is wet. Oddly, this is an intermittant problem. The past two days, with a small load of dishes, there was no leak. Help!!
A reader on another forum found, after much effort, that the solution may be very simple: don't load flexible cutting boards on the right-hand side of the machine.The boards can block an outlet on that wall, presumably leading to a buildup ... Bosch Dishwashers
NEFF S4443 top spray bar not rotating, no water. Bottom spray bar rotates and sprays water. Checked and replaced fine/course mesh filters. Will pump to empty and refill on pre-wash (rinse). Seems the pump may have two outlets one feeding the bottom spay bar (nearest from of machine) and one just behind which feeds the upper spray bar. Running without spar bars attached (including mechanism feeding to bar, water is only being forced out of the from outlet. Any ideas before I start taking it apart
... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher
I have maytag dishwasher model WUR02 Serial no. 609196 ng. Last night I put the dishes and start the machine It runs but hasitating . In the morning when I check the machine the bottom part was full of water . the soap despencer was not opened and the dishes was not cleaned properly . Advise me what should I do. Thanks
Contact an appliance service company. You could have a problem with the electronic control board. \015\012\015\012 ... Maytag Dishwashers
My dishwasher has stopped cleaning plates properly. It makes everything wet but at the end of the cycle the detergent block is half dissolved at the bottom. I have just run a cycle and opened the door during this. The bottom is full of soap suds and water and the top spray bar is dripping water after I open the door but when I close and then reopen a few secs later the top spray bar has definetly not rotated. The water is also not hot, this dishwasher is a cold fed only machine so I guess the el
Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher
Water fills bottom of washer but doesn't get sprayed around
This is the problem with these units, you have to pull it out to get to anything.when they work they are nice but when they break they are a pain in the a---- you get my idea ... Bosch 24 in. SHU43 Built-in Dishwasher
My Kenmore Elite dishwasher (model 665.17462300) is not spraying the water from the basin in the bottom up through the rest of the dishwasher. The basin fills with water, then just makes a humming noise and appears to splash a little of the water around the very bottom of the dishwasher. When we cancel the cycle, it does drain out the water from the basin. I cleaned all the gunk and debris out of the basin in the bottom, but it didn't make any difference.
I have a baumatic mini4 tabletop dishwasher and when i put it on to start a cycle after 2 mins water starts pouring out the bottom of the door and floods my kitchen? i have checked pipes and they are ok and when i switch the dishwasher off and back on again the water drains out the bottom of the dishwasher ok.
Hi,\015\012\015\012As there are a couple of troubleshooting for this leak. As with out doing it is not easy to understand whether its a plumbing issue or the washer is not draining constantly in cycles.\015\012\015\012 ... Baumatic 18 in. BFD46 Free-standing Dishwasher
I have a GE Potscrubber 720 and there is water in the bottom of the dishwasher and I tried to clear it by starting a cycle and it still keeps water in the bottom of the washer. When I run a cycle there is caked on soap on the inside door and dishes and the dishes are filthy. I found a long thin piece of metal by the drain it is long and straight and a break on one end and an "L" shaped bend on the other.. Any ideas where to start looking for problems? As I have no experience in repairing dishwas
... GE 24 in. GSD2600GBB Built-in Dishwasher
Ge model # gsc3200j01ww dishwasher. when the door latch is closed, nothing happens. motor does not start. if the timer is advanced to the next part of the cycle, water will spray into unit until float valve is triggered. water will not pump out, motor does not start. bailed out water, checked for stuck float valve-ok. removed drain screens and filters, cleaned. no motor, drain, or start. what parts should i check? always rinsed dishes before putting in washer. unit is portable or undercounter
... GE 25 in. GSC3200J Built-in Dishwasher
Subject is Bosch dishwasher SHU6800. There is a soap residue left on dishes. Residue is not visible. Using two glasses taken from a recently completed wash cycle I rinsed one under tap water and then filled glass with tap water. The second was just filled with tap water. There is noticeable soap bubbling and foam in the second glass. Starting the 10 min rinse/hold cycle following completion of a full 60 min wash cycle results in considerble soap foam in the bottom of the tub. Have tried thr
WHAT IS WRONG WITH YOUR DISHWASHER? \015\012\015\012\015\012\015\012 \015\012For a detailed Dishwasher ill ... Dishwashers
Hi Model DU1048XTPQ4...when I started the DW today, it sounded kind of loud. I let it continue, then I smelled something burning. What I think happened is that the lower spray arm is too loose-so when it spins, it gets stuck on the heat ring on the bottom of the DW and then the plastic parts start to melt. We disassembled the spray arm and there was lots of calcium/lime build-up. So we cleaned all of that out, put it all back together, but the spray still seems too wobbly. Went ahead and start
The noise coming is from the motor bearings or the impeller which moves with the motor.both has to be checked.\015\012if the bearings are making noise motor needs replacement and if impeller is cracked it needs replacement.\015\012you can get require ... Dishwashers
Dishwasher leaking Our dishwasher all of a sudden started leaking. I've taken the front panel off the door and can see exactly where. It's not a hole or anything...it's at the front, left edge of the basin, the bottom left corner at the front. It seems that right after it fills with water, it starts to leak once water is moving around inside and washing cycle starts. It is as if big waves are being pushed to the front left corner and over the lip of the basin. I don't think the water level is to
Just an idea...if i'm understanding you correctly,could the door seal be creased there or folded over by use and age to permit this to happen? cause you said nothing is missing ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher
My trusty Bosch s510 Dishwasher which has been going strong for about 17 years (at least) has just decided not to empty itself. I noticed the bottom was full of water after a wash. I emptied all the water out by hand and presuming there is a blockage in the drain tried using a plunger to unblock it. I have since put it through another cycle and half way through water started leaking out of the front. At the end of the cycle the bottom of the dishwasher was again full of hot 'soapy' water. If th
Same problem, so went out and bought a new bosch. Problem with the S510 was cured by lubricating the pump out motor bearings with a squirt of WD 40. If you don't know which pump, follow outlet hose to pump outlet.Les ... Bosch Dishwashers
Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th
... Maytag Dishwashers
FDB105OREC4 My dishwasher is not cleaning my dishes. I push the start button and water seems to be trickling in then it stops and no sounds protrude from the machine for several minutes. Eventually another loud motor seems to turn on and drain the water out of the machine. The soap dispenser usually opens and the soap block that usually dissolves is setting on the bottom of the machine. It seems the water is plenty hot but the rotating washer arms might not be moving. Please help me find the par
... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher
I have a Kenmore, Stock 15649, approximately 14 - 15 yrs old that worked fine until the past few days. The upper rack doesn't appear to be getting any water, as bowls and glasses are still dirty after being washed. It appears as though water would spray from the bottom, through a "nozzle" in the middle of the lower rack, then go to an arm located underneath the upper rack. I haven't noticed any obstructions in this path that would inhibit the water from spraying. Any suggestions (outsid
... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher
The is for the model: DDW1899WP. The cycle is getting stuck in the first phase and the soap container is not opening. When I open the soap contain, water has seeped in because the soap is moist and hard rather than loose and powdered. In addition, water is pooling int he bottom of the dishwasher. I tried adding more rinse aid because that has solved the problem in the past but it is still persisting.
Looks like there are two problems here\015\012\015\0121. the controller is not sending a signal to open the soap dispenser door at the right time when the water is flowing through it\015\0122. the drain motor is not pumping the wate ... Danby DDW1899WP Portable Dishwasher
I have an Indesit IDL 42 dishwasher. It has entered a state in which it behaves like this: as soon as I turn it on, it starts swishing the water around (it doesn't pump it out) and it does that regardless of whether I press any buttons (I have tried Start, Reset, turning the program knob, no difference at all). When I open it in the middle of this cycle, the water drips, and there is plenty of water (about 1 in) at the bottom. I have checked the filter, it is clean. Can you please help?
2 weeks ago, I had a plumber come and put in a new garbage diposer and since then somewhat old/dirty water seems to be sitting at the bottom after all cycles are done. I calle dhim back and he says that there is no problem in the plumbing but more with the pump. I even use the wt/dry vac and removed water and ran it but still comes back with water at the bottom. also the dishes smell like soap. Help!!!
The plumber did not make an air gap in the dishwasher drain hose when he reattached it to the new disposal. Look under your sink, does the hose (attached to the disposal) go down and through the cabinet? If so, that is definitely the issue. Simple ... GE 24 in. Profile PDW7800 Built-in Dishwasher