Having problems with your GE Dishwashers ?

My GE Potscrubber 1200 cuts on perfectly and

\015 My GE Postscrubber 1200 cuts on perfectly and sounds as if it's running through all the cycles, but the dishes are FILTHY! Upon further examining, I have found that the detergent cup is opening, but all of the detergent is in a lump in the bottom front corner of the washer, and I don't think the blades on the top or the bottom are moving. I actually set them in 1 position, let it run for a few minutes, and rechecked the position, and they had not moved. Any ideas???????\015

Answers :

Probebly you dont have enough water coming in start the dishwasher,when it starts washing dump a bucket of water in the tub.if it starts moving replace the intake valve
Repair Help & Product Troubleshooting for GE Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My GE Potscrubber 1200 cuts on perfectly and


Probebly you dont have enough water coming in start the dishwasher,when it starts washing dump a bucket of water in the tub.if it starts moving replace the intake valve ... GE Dishwashers

Viking professional dishwasher DFUD142 panel lights flashing, and cannot turn of pump, need to cut power, will not go on? worked perfectly 4 yrs. what to do? repair man did not fix.


... Viking DFUD142 Built-in Dishwasher

I have an Electrolux ESI 6104x. Regularly just after starting the dishwasher as it starts to fill for the first time the water inlet cuts out. If you turn the water off at the mains disconnect the inlet pipe (spilling a bit of water in the process) reconnect the inlet pipe and turn the water back on the dishwasher fills and runs perfectly. This fault used to happen occasionally and now happens regularly.


Disconnect the fill pipe from the back of the machine and you should see a small mesh strainer in side the dishwashers inlet valve. Check that this is not dirty - to clean it pull out the strainer and rinse under the tap. ... Dishwashers

After 15 years of working perfectly, when i try to run my garbage disposal the GFI outlet pops and cuts out the power to the garbage disposal, dishwasher and lights above the sink. It does not


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

My small boy fell on my open dishwasher door (Bosch) and now it's opening slightly in mid cycle and cutting off. It's not leaking or anything and works perfectly if I clamp it closed. When it's opened down then, it's very slightly slanted downwards. I have taken it 2 a repair shop twice and they've failed to sort it saying that its the sensor may need to be replaced but I think it's the hinges are strained. What should I do?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

My dishlex 760 cuts out during the cycle, there


I have the same problem. \015\012Initially, the only problem was the dishwasher was not taking in water. Told to replace solenoid - which i did.\015\012Now the problem is exactly as you explain. Sometimes you have to keep trying after ... Dishwashers

Im having a problem keeping the motor running. it cuts off and will re-start easily and run in the choke mode? won't run in the normal mode until i cut it off and re-start. then it will run for about 5 minutes and cut off again? HELP


Hello. Your carburator is gummed up. Get a can of seafoam fuel additive at the auto parts store and put the recommended amount into the gas. This will clear up the problem in just a few minutes. Joe ... Northstar Pressure Washer 3000 PSI

My kr2020 washer keeps cutting out .the unit appears to get overheated and cuts. after about 10minutes it will start up again for a while before cutting out again


... Karcher K 3.98 M Electric Pressure Washer

I HAVE A BRAND NEW TROY-BUILT 2600PSI pressure washer. I have used it twice for about 1/2 hour each time. It worked perfectly. I tried to use it today with everything hooked up perfectly. The Honda engine started perfectly; how ever when I squeezed the wand trigger, the engine instantley died. I let the engine warm up and slowley pushed the choke in. I let it warm up for plenty of time; but everry time I squeezed the trigger it instantly quit- it even backfired once before dying. I changed the g


Sounds like the governor is stuck. My pressure washer speeds up when it has to pump. Don't know if yours uses vacuum to trigger governor or direct linkage. Good Luck. ... Psi Blue Max 2200 High Pressure Gas Power Washer

Hi I have a LG LD-2052 dishwasher. It gives me an E 0 error - the water does not pump out when I open the machine after a few minutes when started to wash and message of E 0 appears? Have cleaned an


... LG Dishwashers

Fills ok wash ok at 156 degrees goes into rinse cycle dont seem to have much water comming out shows 0 degrees rinse temp. screen is out so thats not clogged have separate free standing electric heater piped in has been working fine for 5 years that way dont understand 0 degree water temp. on display any help would be great thanks for your time joe


... Hobart AM14-253 Free-standing Dishwasher

Washer cut out not a fuse problen is there a reset on the machine or does it cut out if it over heats?.


Should be a reset button on the cord where you plug it in ... Karcher PSI Electric Pressure Washer

I have a BDW 6SL. It stops at about 1/4 of the washs cycle. A repairer reset the thermal cut out and it worked for a few weeks the cut out again. how do it locate this and any ideas what the problem may be. Thanks.


... Baumatic 24 in. BDW6 Built-in Dishwasher

Nothing comes on on my kitchenIaid KUDI24SEBL4.checked door switch(2poles,com and NO3)res was infinite across com and NO3 and 0 when the actuator was depessed.the actuator has to be held down after it clicks to get a 0 resistance otherwise it goes to infinite.is this correct.if so I guess I need to check the timer?


... KitchenAid Dishwashers

Clean button wont cut off and the start buttom cuts off


... Whirlpool DU1301XTV Builtin Dishwasher

Bosch sgs43eo2gb dishwasher. wash programme completes, water drains out, but machine goes on draining, forever, stuck at around 50 minutes on the facia clock. there is no leak on the machine and everything else has been cleaned and operates perfectly. ie,fills correctly,heats correctly and drains fully but won"t stop draining & refill. Cancel programme and reset and it works perfectly until end of wash cycle again, when it continues to drain even with the door open. There is no leak in the machi


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for\015\012using FixYa. Please once again check that the hoses are not kinked or drain pump and filter ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

I have a Neff s4457n0gb/32 dishwasher that will not complete the cycle as it finishes on 0:01 minutes remaining on rinse and not moving to drying. I have to press the reset to clear the display to 0:00. If you've any idea how I can correct this problem that would be most helpful.


... Neff 24 in. S4457 Built-in Dishwasher

Trigger problems When I realease the trigger it cuts off the spraying but then it tries to start back up. It makes a sound like it is cutting on and off. I would like a dirgram of the trigger can I get one. Thanks


It is recommended that once pressure washer is in operation and water flow thru wand is there ,that you do not allow off period between burst of no more that 2 minutes or you highly risk damage to your pump,not engine, due to overheating. See if Dump ... Karcher Pressure Washers

Hi there,i have a brand new but 3 year old,diplomat 8332,just fitted it,it does the pre was ok,pumps out the water,goes to next stage,you can hear water entering the machine,shortly after it has started the main wash,it starts to cut out intermittantly,then F2 code appears,and a bleep.i have taken the lower panel off and checked for leaks and to see if the valve was free,all ok,also relay click in front panel,safety cut out ? any ideas please.


... Dishwashers

I noticed some leakage during operation of my 6 month old dishwasher. After pressing the cancel button, no water runs through the machine when I try to cut it on yet the machine itself cuts on. Please advise.


The circuitboard that runs the timer has possbly shorted out. This isn't something that can be replaced by a novice due to the cause of the shortage may damage the new circuit. I would suggest if the unit is under warranty to have them come out and ... Whirlpool Dishwashers

This dishwasher caught fire it got to hot and burnt the plactie around the bottom by the element. This modle has been recalled what can I do? GSD2620J01SS AG736720B not sure if the 0 are zero's or the number 0


... GE Tritonr XL GSD6260JCC Dishwasher

Pressure washer cuts off when I pull trigger on wand. I changed the oil it is getting better but seems the oil sensor is cutting it off.


Float may be sticking in carb. ... Karcher 2500 PSI Pressure Washer

My portable dishwasher hose that attaches to the faucet is to short for where I want my portable dishwasher to sit. I would like for it to sit in one spot. I am not allowed to alter or cut holes in the side of cabinets, I am renting. Is there an extension for the hose to the faucet? If not, what can I do to make the hose longer? If I really have to I will cut the two hoses that comes from the dishwasher to the faucet, but I would rather have an extension first.


You should be able to find extension or replacement hoses that you can use to extend the existing hoses at a hardware store. If you need to join two hoses that have female connectors, adaptors with two male connections are available. ... Dishwashers

Westinghouse Silhouette 906 dishwasher cuts out after pre-wash, sometimes goes through cycle to rinse, then cuts out. Obtained service from sole dishwasher technician in Ballarat - he was very discourteous, claimed to have corrected fault, charged $125.00. Fault not fixed - that was many months ago but don't want him back. Please advise


... Dishwashers

Machine doesnt start . when on button is pushed and regular wash button is pushed it goes to agent and cycle is at 0 flashing (both 0 and agent lites).have tried to shut it off and main switch and turned it on and off a few times. and still the same


Because the timer controls many operations, a faulty timer can cause many problems. The timer is a complex component, so you shouldn't attempt a do-it-yourself repair. Test the timer with a VOM set to the RX1 scale. To gain access to the timer, ... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0288 seconds