Having problems with your GE Dishwashers ?

I'm not getting any water into the dishwasher, not on wash or rinse. The float float is working feely and I can hear it click when manually pushed. I don't seem to be getting any power to the valve that controls the water.


Answers :

Hi pull the wires off the inlet valve under the dishwasher. Then set the dishwasher for a cycle and test the wires with a volt meter while the unit is supposed to be filling. If you are getting 120v the valve is either blocked or bad, you will have to replace it. If you have any questions please feel free to ask. Mike
Repair Help & Product Troubleshooting for GE Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I'm not getting any water into the dishwasher, not on wash or rinse. The float float is working feely and I can hear it click when manually pushed. I don't seem to be getting any power to the valve that controls the water.


Hi pull the wires off the inlet valve under the dishwasher. Then set the dishwasher for a cycle and test the wires with a volt meter while the unit is supposed to be filling. If you are getting 120v the valve is either blocked or bad, you will have t ... GE Dishwashers

On an AEG Favorit 64570 VI we have an error 20. Manual indicates a drainage problem, however when we pour in water, it gets pumped out without a problem. No obstructing in the exhaust tube. Next we checked the pressure sensor, by taking it out and blowing into it. It clicked as pressure was applied to it, so the inner switch worked. Everything is clean, but still we get an error 20. What does seem strange is that the appliance does not take in water. Any suggestions are welcome.


... AEG 23 in. Favorit 86070Vi Built-In Dishwasher

Neff 4456 water resevoir not filling. Checked float switch and all OK. Checked water supply and all OK. Filled resevoir manually from top of resevoir and program cycle starts but stops when rinse is required.Have stripped down and cleaned switch with float switches as I have had that problem before getting clogged. Any ideas


... Neff 24 in. S4456 Built-in Dishwasher

Dishwasher: Whirlpool Gold Quiet Partner. Has worked fine until had a house plumbing blockage which made water pool in the bottom of the dishwasher as well as kitchen sink. Tried to get it to drain at first using keypad. Drain light clicked on and then off because there was nowhere for water to do. Manually emptied most of the water, then "Cancel/Drain" worked if I held it down quite a while. House plumbing is now fixed. However the keypad only works sporadically now. Some buttons do so


\015\012Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing. ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have a G E Nautilus dishwasher that has been in storage for 2 years. Every thing works but the Drain. When the cycles are finished I' m left with a dishwasher full of water and it dont drain. I checked the bottom as u said in a previos question I see not obstacles, trash etc. How else4 can I get it to unplug? Also where can I get a owners manual? I can be contacted at [email protected] if needed. Thanks ahead of time for the help.


Hello. Here is the link to a free manual http://kitchen.manualsonline.com/manuals/mfg/ge_appliances/ge_ap ... Dishwashers

Bosch SGS5312GB/12 Dishwasher I had a control board. Worked fine except didn't heat the water. Got it repaired (new PCB). Now the only thing it does is drain. Clicks every 20 secs and carries on draining. Got a new board. Does everything (including heat the water) except it does not drain before, between, or at the end of cycles. It does drain when while filling, and if the flood detection rod is raised manually (also drains if the inlet pipe beyond the pressure sensor is blocked - found


... Bosch Dishwashers

The wash cycle seems to take hours. the water wont drain away and i get a little blinky light on the front. i dont have the manual either so i dont even know what the arrow buttons mean on the front of the machine


... Zanussi 24 in. IZZI ALU Built-In Dishwasher

Gaggenau GM 915-710 UC6 dishwasher will not fill and wash. Close the door, turn lever. Empties water from sump. (drain hose was not clamped above disposal outlet nipple, fixed that) Machine empties sump, but will not stop after sump is dry. Will not initiate fill and wash. Manually stop machine. Can't get control board to do the diagnostic to get an F #. Pressing button 1 and 3 at the same time. A couple of the plastic tabs on the circuit boards plastic support housing that link the


... Gaggenau GI936-760 Dishwasher

Water wont drain from the bottom, removed hose and not stopped up. float switch is working but dont know how to test the discharge valve that controls where the water goes, either out drain or back into sprayers


\012Hi,\012Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have a Bosch SHE44C02UC/46 that will finish all of the cycle but leaves a couple inches of water in the bottom. If I pull out the dishwasher and manually active the drain pump float it will drain the remaining water out of the dishwasher. I heard about a cold solder joint on the main controller board but I am not sure if this could be the issue. Please advise wat advise you can. Thanks.


... Dishwashers

Maytag MDB9150AWW model not getting wash water, gets rinse water


Hi,\015\012I think you have thought this through throughly and have narrowed it down pretty good....\015\012The soleniod valve does work or you would not be getting rinse water...\015\012The float is working or the rinse would eithe ... Maytag 24 in. MDB9150A Built-in Dishwasher

I have a Bosch SHU53513UC/U12 dishwasher. My initial problem is that the washer smells bad after a cycle and I've noticed some water sitting in the bottom of the unit. After running a diagnostic test, it results in a "2" heating fault. I followed your advice and used a current coil to and attached it to the GYBK-a1-3 hot wire on the control board. After running the test again, it only gets as high as 1.15A and manual says it should reach 11A. What should I do next?


Hello,Welcome to FixYa. ... Dishwashers

Bosch logixx dishwasher sounds like its running continuously & will go through entire program but does not fill or wash. Filled it with hot water manually to try for air locks & it does drain out. Then continues to attempt to drain even while door is opened. My amateur guess is that its a float switch but can I get at it from the inside or from the back? If thats what it is. Hope you can help,thanks.John


... Bosch 24 in. SGS09L12 Logixx Free-standing Dishwasher

Bosch #SHE44C dishwasher does not fill. No power to the water solenoid, but power coming out of the control board and the emergency shut off float and switch is working. I need a manual with a wiring schematic and cycle sequence so I don't have to tear it completely apart to trace every wire. Thanks


... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Bosch Logixx dishwasher gets stuck on either wash or final rinse programme and runs all night until stopped manually. heat, pump, water supply, arms led controls all working. Any ideas as to the fault


You have a bad control module. send me a 4 thumbs post if this was helpful to you.p.s im a old bosch tech ... Bosch 24 in. SGS09L12 Logixx Free-standing Dishwasher

Hi! I dont have a User Manual for my dishwasher HJA8630 (Lamona). I cant get it to run- despite the fact all lights are lit on the control panel in the door. Can someone advise pleae?! Thanks, Lauren


... Dishwashers

I turned on the dishwasher tonight and noticed nothing was happening, but I was getting a clicking sound. I moved the dial back to off and started over. Some water went in, but then nothing happened again. I clicked forward one click at a time. Sometimes water came in. THEN WATER STARTED LEAKING OUT. I clicked back to off. After water stopped leaking, I opened the door. There is still water in the bottom. What do I do???


Hi \015\012\015\012Thanks for using FixYa. As the water is not draining and clicking is\015\012coming from the bottom so the issue seems to be with the drain pump solenoid. Usually, these issues are related\015\012to ... Kenmore Dishwashers

I have a brand new Miele dishwasher which has worked grate since it was installed 2 weeks ago. It keeps shutting itself off & indicates an F13 fault. I looked in the manual, see that water is going in fine & pressure is good. It then says to clean water intake filter. How do I get to that ? I don't have a user maintenance manual. I'm on city water & doubt that the filter is clogged but My wife will kill me if I don't get it fixed today. Can anyone help. Glenn


On my Miele 1220 dishwasher, the inlet filter is inside the inlet hose connector, where it screws onto the water supply. To clean it:\015\012\015\0121. Turn off the stopcock.\015\0122. Unscrew the inlet hose.\015\0123. Remove the black rubber s ... Dishwashers

I have a Kenmore dishwasher (model 363.14478791). I hadn't used the dishwasher in a month. I turned on the dishwasher tonight and noticed nothing was happening, but I was getting a clicking sound. I moved the dial to the right to off. As I moved the dial to the right, there were lots of clicks and clunks. I started over and turned the dial to the start position. Some water went in, but then nothing happened again. I clicked forward one click at a time. Sometimes water came in. Then water star


... Kenmore Dishwashers

Maytag MDB 4000 AWB. Not cleaning. not getting water now. pressure was low when i was getting water. . Soap dispenser would not open as well. I replaced the motor on the soap door. cleaned the float switch. Tested continuity and cleaned out water inlet valve. Still not getting any water


... Maytag Dishwashers

Water problem Hi, I have a Jenn air DW 711 that does not get water. I checked the following: Water line: I unhooked the water line and it is clear & free flowing. Float: The float moves up and down as it should. Filter: The filter inside the tub is clean. The motor runs and will drain any water in the tub I put a bucket of water in the tub and the dishwasher immediately drains no matter which setting I choose. Any ideas? Thanks, Steve


Many dishwashers will drain at the beginning of any cycle. \015\012If the water does not fill after the pump-out cycle, then the problem is either the fill valve or the float switch. You should be able to hear the float switch click as you rais ... Dishwashers

Control panel will not light up, the dishwasher was running and now it has stopped mid cycle and will not do anything. I just replaced the control panel (black plastic with buttons, not control circuitry). was running the diswasher and it seemed to be working fine, then stopped. water is standing in tub, I checked the float, I don't think the float is the problem. There is power to the outlet, no tripped breakers. But control panel will not light up.


I have a kitchenaid dishwasher model # KUDC10FXBL1 I went to start it and none of the buttons were working. I have checked the breaker and the wiring and everything seems to be in order. ... KitchenAid 34 in. KUDP01FLSS Stainless Steel Built-in Dishwasher

It seems that not enough water gets into the tub. There is no kink in the water line. If you manually add water it drains out before resuming wash cycle. The water doesn't get around to wash the dishes let alone rinse the soap off the door!


If the machine has stopped half way through due to switching off or power intruption this could happen.\015\012\015\012So allow the machine to complete the cycle. \015\012Do no worry running it empty.\015\012\015\012It s ... LG LDF6810ST Stainless Steel Built-in Dishwasher

Bottom tray with float gets full of water and won't let water in until I soak it up with a towel. then it will allow water in and continue. Took float out and cleaned still have the problem. What causes the bottom tray to fill with water? Thank You!


Hello JbcmJones, It would appear that the discharge pump isn't allowing the water to properly drain. Sometimes it happens when a glass breaks and parts of the broken glass get down into the sump area and obstruct the drain area. In order to determi ... Bosch SHU3306UC Built-in Dishwasher

The start timer control cycles but nothing happens. The motor seems to gurgle while attempting to fill with water - but no water comes through. We have had this problem before and the repair person replaced the timer control board. Could this be the same problem reoccuring? I have also tapped and cleaned the water float as described by GE website.


I bought a new one and installed it myself. hardest part of installing was taking the old unit out. I compared the cost of a second repair of a 10 year old dishwasher vs. purchasing a new one. We also checked the pump and solenoid to find problems th ... GE Nautilus 24" Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1960 seconds