Having problems with your GE Dishwashers ?

Dishwasher will suddenly start "beeping" intermittently at several second intervals when not in use. Controls will not funtion at times, then will suddenly be OK, and run through a full cycle perfectly. Later will do the same all over again. I have replaced sequence switch, but no improvement. Does it need a control panel, and if so, should original sequence switch be OK?


Answers :

HI. That original sequence switch shoudl be ok. This will essentially be a control panel issue. There may be one or two button circuits that could have become unstable,thus, causing the intermittent beeping. With that said, i would like to examine the schematics for this unit. If possible, could you post the entire model number?

Thanks..
Repair Help & Product Troubleshooting for GE Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher will suddenly start "beeping" intermittently at several second intervals when not in use. Controls will not funtion at times, then will suddenly be OK, and run through a full cycle perfectly. Later will do the same all over again. I have replaced sequence switch, but no improvement. Does it need a control panel, and if so, should original sequence switch be OK?


HI. That original sequence switch shoudl be ok. This will essentially be a control panel issue. There may be one or two button circuits that could have become unstable,thus, causing the intermittent beeping. With that said, i would like to examine th ... GE Dishwashers

I have a Kleenmaid dishwasher model DW20W and it all of a sudden won't start. The door shuts ok, the power is on and the start light is on. The salt light is also on so we replaced the salt but that didn't help. The cycle seems is stuck on the universal 65 degrees mode and I cant move it forward or backward from that mode. Ive switched it on and off and pressed all the buttons. It won't start. Help?


... Dishwashers

Amana dishwasher, model adb2200aws, ser #, 26650464e. history: quit running, no lights, nothing. replaced the door switch, ran for three days, replaced the switches on both sides of door switch, ran three days, quit. replaced the circuit panel , ran one time, quit. not lights, nothing. when I take it apart sometimes, that is take off inside cover on door, it might run or not. seems like the current isn't getting in as no lights will come one.


I have the same problem with mine as well but I found out that if you take a space heater to it and warm the control panel up for about 5 minutes, everything works great. This model of dishwasher seems to be problematic in any environment under 70-75 ... Amana Dishwashers

Code F2 I just replaced the door switch on an inoperable DD-602. My top drawer was working fine, but my bottom one has been offline for a while (door switch failed and I never got around to fixing it since I had the top). Well, my top finally failed too so I replaced both switches. Looks like everything is good on the top, but my bottom is erroring with an F2 code now. Kindof makes a thumping noise as it starts the cycle -- maybe 3-5 short thumps and then a 10 second delay, repeats. Any ideas? C


F2= \015\012The motor has not\015\012been sensed rotating\015\012\003 Foreign object has jammed the rotor\015\012\003 The rotor has failed\015\012\003 The hall sensor has failed\015\012\003 The electronic controller has ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

My Whirlpool Duet, model WFW8400TWO2, powers up but then shuts off when I hit Start. There are no error codes displayed. I replaced the CCU and ohmed the door switches, the pressure switches, all okay. This failure happend about a year and a half ago but I wasn't around to see what was replaced under warranty. Any ideas?


... Dishwashers

I have a Maytag MDB5601AWB dishwasher. all the switches except the heated dry switch are not working. I did the unlock thing and still nothing . Do I need to replace the switch panel or is there something I should try? I tested for power and have 120 volts coming into the circut board and through the door switch Comments: Aug 22, 2009 - I tested the door swich and I have power on both poles when it is closed. there is 2 switches on the latch but the one with power to it powers up the circ


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

The start switch (right side) not power switch (left side) broke....(below the overlay). I need to replace the switch and overlay. What part(s) do I need to fix the switch. I now have overlay part number. This is for "start" switch... Thanks


Hello again,\015\012\015\012I'm glad I was able to help you earlier with the overlay, unfortunately I'm not sure I can go 2 for 2 because the start switch issue is going to be a little more involved.\015\012\015\0 ... Asko 24 in. 1805 Built-in Dishwasher

Bosch SKT5102 The machine wont stay on. When I push the on/off switch the machine comes on for a split second then goes off. If I hold the switch in then the machine works. I have taken the back off and located the micro switch and note that I can buy a replacement. Do you think that is the problem and will I just be wastin my money on a new switch if not. Thanks


It sounds like the switch but you don't need the bosch one if it is only the micro-switch they are easily available\015\012ger531 ... Bosch 22 in. SKT5002GB Built-In Dishwasher

I have a Maytag MDB5601AWB dishwasher. all the switches except the heated dry switch are not working. I did the unlock thing and still nothing . Do I need to replace the switch panel or is there something I should try? I tested for power and have 120 volts coming into the circut board and through the door switch


Possible switch panel. When you press it does it feel like a click as the the other buttons? If so you probably have a bad circuit on the inside, if it doesn't click the heated button switch is more then likely the cause. ... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

I have a kitchen aid dishwasher model number KUD101TJBLO. I have had the thermal fuse replaced numerous times. It may run two weeks ir it may rub two cycles then the fuse blows. My serviceman has given up on finding a solution.He has replaced the control board and the door switch. However it continues blowing the fuse. I read on the internet that you need to replace the entire wiring kit that comes with the fuse but my repairman says this will not fix the problem and refused to replace the kit.


Hi\015\012\015\012\015\012Thanks for using FixYa. Please check for the short on the wires near the heating element. Also check the resistance of the heating element, it should not be more than 1.6 K ohms. Also ma ... KitchenAid Dishwashers

Clean light comes on my Kenmore Elite Dishwasher Model # 665.17263. This happened once before and has to do with the heating element. The service guy showed me how to press the buttons in a certain sequence to "unstick" the unit and it worked fine. The Quick Rinse light keeps flashing. When I push a previous sequence recommendation it switched to pots n pans and Quick Rinse and Cancel all started blinking. Then in about 2 minutes went back to Quick rinse. I did one sequence and it started to d


It seems that there is something stucks in your dishwasher...is there any error code? ... Kenmore 24 in. 15079 Built-in Dishwasher

No Power, my raise green light lit when power off. when switch depressed, red light does not lit, no power. in any cycle. I replaced the power switch, and the door switch. No luck Please help


Hi, you will need to inspect the terminal block for damage , as well as, the control board for damage. The terminal block is the device that will have the power cord wired directly to it. make sure this block isn't damaged. inspect for any discolorat ... Dishwashers

Have a Bosch shy56a05uc dishwasher that suddenly stopped working to a point. I believe it is related to the door latch switch, because I don't feel the door securely latch shut when I close it, and I also don't get any cycle lights or times registered on the LED readout. If I depress the on switch, the drain pump will start even with the door open, and, depending on how long I leave the switch on, water will start to fill in the dishwasher, open or not.


Does your dishwasher electronic control or mechanical timer? if mechanical timer, I encounter a similar problem n change the mechanical timer. that problem solved.\015\012\015\012Prince P ... Dishwashers

Program stops When the machine is switched on it runs for a minuite or so then stops and bleeps and shows blanks - - - - I switch it off and again re-start and it again repeats this as above the filters have been cleaned and the water was drained and again it persists, the machine is 3 yrs old. I tried a sequence described as switching the programm button in 4 quick times but this didnt work either. Is there any other way we can re-programe this dishwasher or is it that there is a fault where so


... Smeg 18 in. DWD409SS Built-in Dishwasher

My Maytag dishwasher (DWU7400BAE)does not turn on. The latch micro-switches work; replaced the timer switch, still doesn't work; makes no sound of any kind when timer switch is turned. Could this be a relay problem, or is there a solenoid that activates the water flow?


... Maytag Dishwashers

My Indesit dishwasher needs to have the micro switch aquastop replaced but not sure which wire goes on which contact on the switch. Two wires , one pink and one brown.


... Indesit 24 in. DI67 Free-standing Dishwasher

Where can I get a replacement drum switch ??


You can find parts manuals here.\015\012http://www.jacksonmsc.com/?xhtml=xhtml/jac/us/ ... Jackson 25 in. Conserver XL Free-standing Dishwasher

Door switch Anyone know how to determine if a door switch on a dishwasher needs replacing?


Youd have to open the control panel and OHM out the switch with a mater to ck if it functions properly, however upon open panel its sometimes obvious that a switch would need replacing( for instance ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

Need wiring diagram for a hotpoint df22 dishwasher on/off switch, the switch in it has been replaced with the wrong one so i have no reference to connect up the new one. thanks


You're in luck - I've just had one apart to repair the wiring loom.\015\012The door switch is a simple two-pole latching switch with the wiring as follows.\015\012\015\012This is the order of connections from the front.\015\01 ... Dishwashers

Coleman mobile home furnace...Model number DGAA077BDTB...The furnace about a month ago started going out ( flash code- Combustion Air switch stuck closed)We replaced the thermostat on the wall and it stopped doing it and ran fine then last night it stopped again ( Combustion air switch failed to close) and when i got up the furnace was working and now for the past few hours it refuses to do anything...I am on a very very tight budget...and need some idea of what is wrong and do i need a professi


I had the same errror code on my coleman furnace (3 flashes combustion air switch failed to close) but at first didnt realize there was even a light that gave codes..Anyways long story short, after searching many forums one guy mentioned about the fu ... Dishwashers

Dishwasher leaking we replaced the float switch. It is still leaking. Is there a valve that needs replaced? Would like to fix ourselves instead of paying $129 plus parts.


Try checking the rubber door seal if it is not sealing properly dish washer will leak just below the door it is easy to replace and not that expensive ... Kenmore Dishwashers

It doesn't work at all no lights anywhere. I ordered and replaced new switches, and replaced the control board. The circuit breaker is on, and if I put one of the little meters that just tells if you have either 120 or 220 volts accross the two white wired connections on the board, 110 lights up. The float seeks to move freely.


If you have no lights at all and you have power to the circuit double check that the circuit board is connected properly first since you replaced that. On some models there is a safety circuit installed that disconnects power in the event it detects ... Kenmore 24 in. 15932 Built-in Dishwasher

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Repairman out twice...quote too high -replaced plug in parts Sears guy said were needed in control board area. Still-blinking lights /no water filling/no progress thru sequence. Sequence shown on "


REPLACE WATER INLET SOLENOID ... Kenmore 24 in. 16309 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0884 seconds