Having problems with your GE Dishwashers ?

We have a 2year old GE Adora dishwasher model# ghda670n20bb. It fails to runs completely or finish its cycle. now really nothing at all. iy appears that when i press hard on the door it will run but that is not practical. perhaps it is some kind of sensor or contact in the door/


Answers :

Repair Help & Product Troubleshooting for GE Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a 2year old GE Adora dishwasher model# ghda670n20bb. It fails to runs completely or finish its cycle. now really nothing at all. iy appears that when i press hard on the door it will run but that is not practical. perhaps it is some kind of sensor or contact in the door/


... GE Dishwashers

Door interlock appears faulty on my whirlpool awm 321 . It wont allow program start when door closes . Needs a lot of coaxing , banging with palm of hand , knee etc .Door itself appears fine , catch looks ok , finishes and runs ok once we finaly get it started .Hve tried pressing the interlock slider in with a pencil , but cannot succeed in pushing the contacts into place and starting the program . HELP PLEASE


Only solution is to replace the interlock - it is just held in by 2 screws ... Dishwashers

My dishwasher is a Smeg model STA 6143, and the door won't close. It seems fine until the last few centimeters, then it jams and won't close easily. If you press hard, it'll shut but not latch. Nothing appears to be stuck anywhere. We've tried jiggling the door but it seems somehow to be misaligned, although there's no reason why it should all of a sudden appear to be so. The electronics work fine, the racks fit fine (we also removed them, and the door still won't close), and nothing appear


... Dishwashers

Kitchen Aid dishwasher Model# KUDP01FLSS. 2 problems #1 Won't run unless you press in on the door and hold it for a few minutes then it runs through cycle normally. Problem #2 It won't drain water out at the end of the cycle when I open the door there is water laying in the bottom of the tub. I have checked the drain hose for clogging and it appears normal. I am able to remove the hose from the disposal and suck the water out of the tub using a shop vac this indicates to me that the drain is ope


... Dishwashers

GE Nautilus Dishwasher latch would complete the contact. If pressed hard, it complete the contact and start to run the dishwasher but when let go, stops running the dishwasher


Hi\015\012\015\012Thanks for using FixYa. From what you have described it seems that the latch\015\012has gone bad and should be replaced. You can click on this ... GE Nautilus 24" Built-in Dishwasher

The Simpson Silencio 850 door does not shut properly and the dishwasher stops operating,but once you push hard on the door,the dishwasher starts again. There are no leaks ,but the door must have a sensor registering the correct pre-load force against the door seal , which in turn,allows the machine to operate. My machine does not work until you push hard against the closed door. What is the problem please?


... Dishwashers

Boash she4amo Getting a Sensor Error (FS) E:06 when running the Customer Service Program....indicated by the CLEAN led status being lit....thought it was a door sensor failure (chart indicates "door" in the chart beside this failure....but further testing indicates the unit knows if I open the door, and stops the program, so it isn't that.


... Dishwashers

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

Bosch SHX46A (6 years old) Selected regular cycle, pressed On and closed door. Cycle did not start normally. Pump runs, but no water is coming into the DW. I confirmed the water supply line is turned on. I opened door, turned off On/Off switch, then poured water into drain. Then turned On/Off switch on. DW began pumping water OUT of the DW. Also, it doesn't matter if the door is open or closed - if you turn the DW on, the pump will run. I suspect a problem with the electrical controls, or perha


From your description, I doubt that the problem is door latch is the cause.\015\012\015\012The first thing that a modern dishwasher does before it begins to fill with water is run the drain pump.  It appears that this DW is not progressing ... Bosch Integra® 500 SHX46A0 Dishwasher

Dishwasher will not start upon lowering the door. appears to have some kind of magnetic sensor on the door that is cracked and falling off the door. Unable to tichten the screws holding this sensor


"Universal Duct tape". Apparently, one needs to be channeled through a Hobart distributor.Am still checking that out to see whether they will ship me the inexpensive part (Guess <$20)or whether it will be necessary to have a Hob ... Hobart 24 in. LXIH-3 Built-in Dishwasher

When I close dishwasher door, I have to press hard to lock the door. Is this normal?


Check the catch where the door clips into. It might be loose. If so tighten the two phillips screws, then try to close the door. ... Dishwashers

Dishwasher will not run when door is closed, jiggling the door sometimes will allow the dishwasher to run. My guess is there is a contact problem by the latch but I can not find any parts or repair manuals for this Asko 1585. Any insight?


You need an interlock you just take the top panel of and its screwed on underneath handy enoungh to do just make sure you unplug it first :) ... Asko 1385 Dishwasher

Model # SHU 8806UC/14 When start button is pressed, with door open, it begins to cycle and even if we close the door it just runs and runs but never dispenses soap from the dispenser or even fills with water. Any thoughts?


... Bosch Dishwashers

Our normally quiet Bosch SHX36L Dishwasher has started being noisy while running. I found if I lean on the door it closes a bit, and the sound returns to the level it used to run at. It appears that the door isn't closing tightly anymore, but we can't see an obvious fix for this. Thanks for your time!


Your lock plate inside the machine can be worn but it can also be the gasket of the door. Door gasket is the easiest fix ... Dishwashers

Jdb2100aws dishwasher - door handle fasteners loose, handle ready to drop off. This is a dissambly question: The middle section of the door has an upper one-third (which contains the input switch strip) and a lower two-thirds; the upper section must be removed to tighten the door handle fasteners. After wiring is disconnected (yes, power is OFF), the upper section appears to be held to the shell by some kind of barbed fastened from the inside, run through a tab on the door shell and into a fema


After removing the stainless cover l tried to disassemble the door further but found it difficult, there is a hard thick plastic cover, i took my dremel and cut a small hole large enough for a wrench to fit and tighten the thin nut on the handle, lin ... Jenn-Air 24 in. JDB2100AWS Built-in Dishwasher

After the cycle runs i open the door and all the soap appears to have just dumped out and is on the inside of the door. I have tried liquid and solid tablets of detergent and neither it working. It seems the soap door isn't opening at the correct time. The washer has only been used for a year! Any ideas of an easy fix? Thanks


Sound like you have to change your dispenser.chek out sear parts direct.com for parts,image,prices and part #s let me know if i was helpful. ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

I have a Kenmore dishwasher model # 66513449K900 that will not stop running. I think it is stuck on the drain cycle. I can start the dishwasher on a cycle and it appears to clean the dishes, but after the cycle is complete, it continues running and running (on the drain cycle) until you open the door. What could this be?


It is possible that the machine does not move off the cycle because there are errors or back feedback from the inputs. For the program to end the main program controller must receive the feedback so as to switch off the circuit at the end o ... Dishwashers

Touchpad--No Response The touch pad and Countdown timer display will NOT respond except when the Rinse Only pad is pressed. The Countdown timer displays "9" when this pad is pressed. As expected the light and display turn off after 30s. If after 30s or longer the Start/Cancel pad is pressed with the dishwasher door closed, then the Countdown timer displays "2H" and the dishwasher runs through the ?Auto Clean? or ?Heavy Wash? cycle. Not sure which since neither pad is lit. Is the problem the


The "2H" is an error code indicating the control panel needs to be replaced. ... Bosch 24 in. SHU53 Built-in Dishwasher

I have a Kenmore dishwasher model #17519200. I loaded it last night as usual and closed the door. I pressed the wash cycle I wanted and pressed the start button. I heard it starting to fill with water as usual. After it filled with water it should have gone into the wash cycle mode but it just started making a buzzing noise for about a minute or two then just stopped. I pressed cancel to drain it and it drains fine. I have kept trying to re-run it but it just does the same thing I described.


... Dishwashers

Door latch won't close on dishwasher. Hard to close. In addition door squeaks very loud- almost like it is catching on something. the dishwasher moves slighly when trying to close the door -it doesn't appear to be properly installed


... Jenn-Air JDB3610 Built-in Dishwasher

My DS603 randomly stops/pauses like if the door was pulled. The very same beeps and lights are enabled when physically pulling the door while a program is running. How can I make sure that the door state sensor (closed/open) is working properly? I have an integrated single drawer system. Thanks for your help. Ben.


... Fisher DS603W / DS603B / DS603I Dishwasher

WHEN THE START BUTTONIS PRESSED DOWN THE 2 LIGHTS ON THE RIGHT OF THE PANEL LIGHT UP BUT WHE THE BUTTON IS RELEASED THE LIGHTS GO OUT AND THE WHEN THE DOOR IS SHUT THE MACHINE WILL NOT RUN


... Electrolux 23 in. ESL6114 Built-in Dishwasher

I have a Frigidaire Dishwasher, model #FDB635rfs It is not that old, but appears to have quit working. It sounds like it runs the water gets pushed in by the tube on the side but goes straight to the bottom of the washer. It looks like the spray arms are not spinning. Water is not circulating. Element still heats up. Detergent just runs down the inside of the door and doesn't dissolve since water is not circulating through arms. I have just replaced the water inlet valve and it did not hel


Don't know about yours but many of the rotating spray-heads are turned only by waterpressure, not a separate motor.\015\012The rotator is normally pretty loose and should turn willingly by hand; if it seems stiff and your water pressure is normally l ... LG LDF6810 Built-in Dishwasher

I have a kitchenaid dishwasher model KUDS01FKSS0 which is not running. For the past 2-3 months it occasionally stopped mid cycle with water still at the bottom of dishwasher but eventually resumed working. Now it just doesn't run any more and there is water presently in the dishwasher tub). The user interface part (keypad) seems to be working. I can press the keys and the corresponding LED would light up. However after I close the door, nothing happens. There is also no noise what so ever. Any i


THE MOTOR SHOULD MAKE NOISE IF ON, CHECK THE MOTOR OR TIMER. ... KitchenAid KUDS01FKSS Dishwasher

Dishwasher I am moving into a new home with an existing dishwasher. This appliance appears to be newer, but when looking inside, the tub and door have a huge mineral/calcium build up. I am assuming its from the hard water that is pumped through. What do you recommend to remove the hard caked on deposits? Thanks for any advice. Nancy


Its a lime buildup.go to an industrial cleaning supply wharehouse (maybe home depot-lowes),and get delime.you can go to a supermarket and buy c.l.r. (calcium lime remover) but if its real bad you need a stronger delime.simply put the delime in the un ... KitchenAid 24 in. KUDI01TJ - Multiple Color Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0924 seconds