Having problems with your GE Dishwashers ?

GE Profile Dishwasher about 7 years old. everything seems to work door locks the machine trys to pump water in but it can't. I put water in thhe bottom of the machine and it does work a little but verry weak spray. It does pump out fine. Help


Answers :

The washer doesn't pump water in--plumbing water pressure forces it in when the water inlet solenoid opens the valve. Check the water inlet solenoid--they are a common failure point. Look under the front of the washer behind the panel to find it--just trace the water inlet line. It connects directly to it. The valve can be stuck shut or, more commonly, the plastic coil form of the solenoid disintegrates. In any case, just replace it. Don't forget to shut off the water supply valve under the sink before you start work. Hope this helps!
Repair Help & Product Troubleshooting for GE Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

GE Profile Dishwasher about 7 years old. everything seems to work door locks the machine trys to pump water in but it can't. I put water in thhe bottom of the machine and it does work a little but verry weak spray. It does pump out fine. Help


The washer doesn't pump water in--plumbing water pressure forces it in when the water inlet solenoid opens the valve. Check the water inlet solenoid--they are a common failure point. Look under the front of the washer behind the panel to find it--jus ... GE Dishwashers

I have the two drawer dishwasher. It's about 10 years old. The top drawer continues to work OK but for the last three attempts when I run the bottom drawer water gets out into the drip pan below and gives the F1 signal. I can dry the drip pan out and clear the F1 signal so the top drawer works. But running the bottom drawer causes water to leak again with the resultant F1 signal. There is very little water in the bottom drawer (just a little in the filter bowl) so I think the pump is pumping


Hi,Unless you keep using the wrong detergent or keep putting dishes that \015\012are to tall in there. i would have to say your actuators ar bad and its \015\012not letting the lid go down to seal it all the time.There is no adjustment. Y ... Fisher and Paykel Dishwashers

Dishwasher LFK-011S: First it occasionally gave four beeps (overflow) but no water in bottom or under. I then noticed that with lower water pressure machine worked ok few months. Now last week in the middle of program, drain pump started to run, machine gave four beeps and pump kept running even main switch off. Now when I plug in power cord, the pump starts to run immediatelly


... Fagor LFA013 SS 23 in Builtin Dishwasher

My plumber just installed a new water supply line for my dishwasher. Now the pump comes on but no water fills up in the machine. If I fill the bottom of the unit with water, it works just fine. Even though the water supply is ON, it does not pump water into the 'box'. Thanks, Art


You don't know how many times I've heard and found the shutoff valve off or partly turned off. Water entering DW is from line pressure not pumping. Items to suspect (again) the water supply valve (would'nt be the first time a new valve is bad). The ... Whirlpool 24 in. DU915QW Built-in Dishwasher

G.E. GSD5130 When the dishwasher is pumping out the water a small amount comes in the rotating sprayer head. At the end of the cycle the dishwasher still has water in the bottom. The amount of water varies from just a little to over an inch. I replaced the spring loaded check valve a couple of months earlier and everything worked fine until now. What should I check? Thankyou.


Mike, I just ran into the same problem. I found a second check valve located in the outlet hose of the ELECTRIC drain motor. This motor is located at the right rear underside of d/w and is used only for backflush of the filter. When the unit goes th ... GE GSD5130 Dishwasher

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Towards end of dishwashing cycle error code comes up and consitently beeps, can not turn off by machine buttons or reset. We have to reset by power plug. Water is left in bottom of macine, dishwashing powder is left on most things. Rinse button then works, it then drains the machine no problem. So I dont think it is the pump.


No response ... Dishwashers

I just finished a service call for my 5312UC/UC12. The tecnician says he saw water leaking under neath the machine but hoses were secure and no visible crack to the motor housing, The machines pump works but very little water is actually put into the tub, hence no dishwashing. This technician says that this is a repair that most technicians avoid because it takes a long time and costs alot and violated some sort of warranty. He recommend replacement after only 7 years!


This leekage may come from thermostads water isolation ring, just under rezistance leads. There must be a ceramic holder to fix it to rezistance. İf it is broken, thermostad may go down, or rezistance leads isolation (lastic washer) may leak wat ... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

GE Nautilus My dishwasher is approx. 6 years old. It has recently started having this problem. On the second cycle (the one where the little door inside opens and release the soap) does not want to work right. The door will open, but it is like there is no water spraying to spread it out. The soap (I've tried both liquid and powder) sticks and drys, running down the door and in the bottom of the tray. I have to open the machine and add the soap to the bottom of the machine if I want to get my di


Smoking from GE (Model:gsd3725f00bb) dishwasherWe moved in an old house, the dishwasher had been installed. but today we found smoking from the dishwasher and smells burned plastic. Could you have any resolution for me? or this problem is popul ... GE Nautilus 24" Built-in Dishwasher

Dishwasher The dishwasher detergent door opens during cycle but powdered soap remains in tray. At end of cycle glasses and dishes are wet. a little water is left undrained at bottom. This is a Frigidaire model FDB510LCS1. Checked upper and lower spray arms and they seem ok and pump seems to be working


I have seen this problem before on a couple of dishwashers.\015\012\015\012How are the dishes doing? Are they coming out clean, or do some of them "fail". \015\012\015\012If you rinse the dishes before putting them in the di ... Dishwashers

We have a Fisher& Paykel dishwasher with 2 drawers -- one on top of the other. Model DD603. The bottom drawer works fine. But the top drawer is not working properly -- it repeatedly stops in the middle of the cycle and there is water left in the drawer. Previously when this happened, we called a repairman; he removed the top drawer from the machine, said it was "off track", flipped some lever, and put the drawer back. He seemed a little embarrassed by having to charge for a service call for


Are you able to provide a bit more information on what you see when the dishwasher stops in the middle of the cycle -\015\0121 - is it displaying the time remaining in the cycle and is it always the same time?\015\0122- do you get any fau ... Dishwashers

Hi, I have a Kenmore 15879 that is basically working except the bottom water spinner...lol (don't know technical name). The dishwasher pumps the water into the bottom of the dishwasher, will heat the water, but not disperse the water in the spinning sprinkler manner it's suposed to. I've opened the dishwasher in time to see that water is spurting out of the holes about 2" high, but it's just not spinning. The water also drains just fine after the whole cycle.


This is caused by the impeller being clogged or the pump is failing, When the pump is woring properly the water will shoot out with force. ... Kenmore 15879 Built-in Dishwasher

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?


... Dishwashers

I have a Bosch dishwasher, M# SHU3035UC/U12. After the cycle is finished, the water is still on bottom of machine, it doesn't pump it out, so I changed the pump. Now when it washes, it fills and washes, when the timer advances it dies, there is no noise and nothing happens, the only way that I get the machine to pump water is by lifting the red overflow lever. Only then does it pump out the water. what can be my problem?


Hi There,\015\012\015\012Your description seems to indicate a fault in the water heating circuit or components. This is often the reason for a wash cycle not finishing and draining. As the machine will drain when you lift the overflow lev ... Dishwashers

Dishwasher fills with water, but spray arms don't spray water or spin. As the cycle moves forward, water is eventaully pumped out (so the pump is working). i've selected different cycles with the knob on the front of the machine but they all work the same.... no swishing with the spray arms. When the cancel button is pushed, the water is pumped out... as it should. Thanks for the help.


... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers

My Miele dishwasher (G 856 SC) is about 9 years old and has begun stopping in the washing cycle. The pump still drains the water when I reset but it no longer finishes the wash. Any ideas other than to replace the machine! I have tried restarting and cleaning the bottom large filter (both of which used to work) Thanks


... Miele G892SC SS Dishwasher

I have a kitchenaid Model KUDW03CTBL2 dishwasher. It is pumping water, but the top sprayer and the one under the top rack just have a little water coming out. Not enough to make them spin. We also noticed the water in the bottom when opened is not as much and it is cool not hot. The dishes on the top rack will not clean, and the bottom is not completely clean. We have checked water pressure and water tempurature through the house, All is operating fine. This dishwasher is only 1 year and 10month


... KitchenAid Dishwashers

I have a hotpoint aquarius df23 dishwasher. when i turn it on for a wash there is no water coming into the dishwasher. i have put water in with a bowl and it works as normal until it drains the water out. my washing machine is plumbed in to the same pipework and it is working fine. does the dishawasher have a water pump that may need replacing????


Most likely you have an air lock in the dishwasher.\015\0121. Refill the salt compartment.2. Turn of the water supply at the mains.3. Disconnect the diswashers water hose from the mains supply.4. Lower the water hose and allow ... Dishwashers

Hi Dishwasher BOSCH SMS53L02GB start of program digital display shows all sensor working. Water not pumping in. All hoses and filters checked OK Machine pumps water out then completes cycle in 1 minute. Water supply getting to base of machine An E21 code shows up on fault finding cycle


... Bosch 607335 Water Valve Assembly For Dishwasher

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

Hi, I have an LG LDS4821 dishwasher and it appears to stop working properly. The dishes don't seem to be cleaned at all. It seems like the spray arms are not spraying the dishes as the dishes are still dry/dirty after a normal wash cycle. I did notice that the detergent was used during the wash, and a trail of white residue was at the bottom of the tub. I can hear water pumping into the dishwasher, but when I opened it during a wash cycle, there was a puddle of water at the bottom of the


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... LG LDS4821 24 in. Built-in Dishwasher

Model No: SE6 TIE 1 GB/17 Tecnik integrated dishwasher The dishwasher started to make a strange noise. I scooped the excess water out of the bottom and reset the machine but when switched on again it just pumps water into the bottom of the macine. I have removed and cleaned filters as per the manual troubleshooting section! Thanks for any assistance


... Tecnik Dishwashers

Hotpoint hda3440g02sa leaves a little water at the bottom of the dishwasher I have checked the check valve have even replaced I have put a high loop in the drain hose and still no help it leaves just a little water I hate to put a new pump because I have on this type of dishwasher before and still no help


Hi\015\012\015\012 \015\012\015\012When the dishwasher leaves just a little water and drains\015\012maximum then I would say that it is fine & the drain pump is also working\015\012fine. These units are designed in such a way tha ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2663 seconds